2012 PEUGEOT 4007 reset

1
INSTRUMENTS and CONTROLS
The total distance is dis-
played in zone 1
of the
screen and the trip dis-
tance in zone 2
.
DISTANCE RECORDERS (A/B)

System for measuring the total distance
travelled by the vehicle during its ser-
vice life and the distance travelled in
a day or other period until it is reset to
zero by the driver.

Zero reset

With the ignition on, press the INFO
button for more than 2 seconds until
zeros appear.

When the engine is run-
ning, this indicates the tem-
perature of the coolant.
COOLANT TEMPERATURE
If the bar is close to the critical
position
located on the right, the temperature is
too high.
The symbol fl ashes when your engine
is overheating.

You must stop your vehicle as soon
as it is safe to do so.


Wait a few minutes before switching
off the engine.

Wait for the engine to cool be-
fore topping up the level. The
cooling system is pressurised.
When the engine is
running
, this indicates
the distance which can
still be travelled with
the fuel remaining in the
tank based on the aver-
age fuel consumption
over the last few miles/
kilometres travelled.
RANGEGE
When the range is less than 30 miles
(50 km)
, dashes are displayed.
Refuel as soon as possible. The display
of the range is updated.
To avoid any risk of scalding,
unscrew the cap by two turns to
allow the pressure to drop.
When the pressure has dropped, remove the cap and top up the
level, if necessary.
Contact a PEUGEOT dealer or
a qualifi ed workshop. This fi gure may increase fol-
lowing a change in the style of
driving or the relief, resulting in
a reduction in the current fuel
consumption.
If you only add a few litres, the
value displayed will be incorrect.
Therefore, you must fi ll the tank
whenever possible.
When you disconnect the bat-
tery, the previous fuel consump-
tion data is lost and the value
displayed will be different from
that displayed before the battery was disconnected. The distance
displayed must be considered
an approximate indication.

1
INSTRUMENTS and CONTROLS
SERVICE INDICATOSERVICE INDICATOR
Resetting the service indicator
to zero
Your PEUGEOT dealer or a qualifi ed workshop carries out this operation after
each service.
If you have carried out your vehicle's
service yourself, the zero reset proce-
dure is the following:


)
switch off the ignition.

)
press the INFO
button several times
in succession until the service indi-
cator is displayed.

)
press and hold the INFO
button for
a few seconds until the spanner
fl ashes
.

)
press the INFO
button while the
spanner is fl ashing to change the
display "---"
to "CLEAR"
then the
time remaining before the next ser-
vice is due is displayed.


Service overdue

Operation

When the ignition is switched on, you
must press the INFO
button several
times in succession until the service
indicator is displayed. The distance re-
corder display line indicates the number
of miles (kilometres) remaining and the
time elapsed line indicates the number
of months remaining before the next
service is due.
After a certain distance and a
certain time, the display of "---"
is
reinitialised and the display indi-
cates the time remaining before
the next service is due. System which informs the driver when
the next service is due in accordance
with the manufacturer's servicing
schedule.
The point at which the next service is
due is calculated from the last service
indicator zero reset.
It is determined by two parameters:


- the distance travelled (in miles (km)),

- the time elapsed since the last ser-
vice (in months).
The distance remaining to be travelled
may be weighted by the time factor, de-
pending on the user's driving habits.
Example:
the display indicates that
7300 miles (kilometres) remain before
the next service is due.
The symbol "--"
remains dis-
played until the fi rst service of
a new vehicle has been carried
out.

Example:
the display indicates that the
service is overdue. This service must
be carried out by a PEUGEOT dealer
or a qualifi ed workshop. Each time the ignition is switched on,
the display "PERIODIC INSPECTION"

is displayed for a few seconds to indi-
cate that the service must be carried
out without delay.

1
INSTRUMENTS and CONTROLS
TRIP COMPUTER
Average fuel
consumption
(l/100 km or km/l or
mpg)
This is the average fuel
consumption since the
last zero reset.
This fi gure may change follow-
ing a change in the style of driv-
ing or the relief resulting in an
increase or decrease in the cur-
rent fuel consumption.


Average speed (km/h
or mph)
This is the average
speed calculated since
the last zero reset.


Resetting the information to zero

When the ignition is switched on, the
zero reset switches automatically from
manual mode to automatic mode.
If dashes "---" are displayed
for long periods in place of the
digits while driving, contact a
PEUGEOT dealer or a qualifi ed
workshop.


Current fuel
consumption
(l/100 km or km/l or
mpg)
This is the average fuel
consumption during the last
few seconds of driving.


Information display

With the ignition on, press the INFO

button on the dashboard, to the left of
the instrument panel, several times in
succession to display the different infor-
mation:


- average fuel consumption,

- average speed,

- current fuel consumption. When the required information is dis-
played, press the INFO
button for more
than two seconds to reset all of the in-
formation to zero.

Automatic
If the ignition key remains in the OFF
position for more than 4 hours, the in-
formation is reset to zero automatically.

1
INSTRUMENTS and CONTROLS
Set the time using the buttons as indi-
cated below:


)
with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK
button until the
time display fl ashes.

)
Press the appropriate button to set
the time:

Button
H:
to set the hours
The hours digits scroll when you press
this button.

Button M:
to set the minutes
The minutes digits scroll when you
press this button.

Button 00:
to reset the minutes to
zero.


- from 1 to 29 min
:
rounded down to
the previous hour,

- from 30 to 59 min:
rounded up to
the next hour.


)
After setting the time, press the
DISP
button; the time display stops
fl ashing.


Manual mode

Automatic mode

In this mode, setting is automatic using
the signal from the RDS radio stations. The digital clock does not dis-
play seconds.
When the "minutes" display is
set or reset to zero, the clock
starts at the zero second of the
minute selected.
The time setting is lost if the bat-
tery is disconnected.


)
Turn button B
"TUNE" to the left or
to the right to select "CT ON"
(auto-
matic mode) or "CT OFF"
(manual
mode).

)
After selecting the mode, you can
exit the "Functions setting mode"
menu by pressing button B
"TUNE"
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the "Functions setting mode"
menu automatically.

11
AUDIO EQUIPMENT and TELEMATICS

Calendar, trip

These double arrows permit
access to the driving infor-
mation screen, previous or
next. D - Consult the driving information:
D1 - the average speed,
D2 - the average fuel consumption,
D3 - the current fuel consumption,
D4 - for speed and fuel consumption
graphs in 5 minute intervals,
D5 - choose an automatic reinitiali-
sation (key at off for more than
4 hours) or manual reinitialisation
(press [Reset]),
D6 - the distance which can still be
travelled (in relation to the fuel
remaining and the recent aver-
age consumption),
D7 - the distance travelled since the
fuel tank was last fi lled (press
[Refuel] to reinitialise),
D8 - the driving time (duration be-
tween the key being turned to on
then to off).
- press [Start] to measure inter-
mediate times with:
D9 - the duration,

D10 - the distance,

D11 - the speed,

D12 - the fuel consumption. C - Make a note on the calendar of
special days, birthdays, ...
Use the arrows to fi nd a date
and press directly on the day re-
quired to enter the event.
D1D2D3
D4D5
D6D7D8
D7
D9D10D11D12
D
C