2012 Peugeot 208 instrument panel

103
4
Driving








Memorising speeds
This memorisation of speeds applies to both the speed limiter and the cruise control.
You can memorise up to 5 speed settings in the system. By default, a few speeds are already memorised.


Memorisation

To select a memorised speed: )
press and hold button " + " or "- "; the systemstops at the closest memorised speed,)
press and hold button " +
" or "-
" again toselect another memorised speed.

A reminder of the speed and the state of thesystem (on / off) is displayed in the instrument
panel.
) Go to the main menu by pressingMENU.
For safety reasons, the driver mustcarry out these operations when stationary.


Selection
)Select the "Settings" menu then "Vehicle settings".)Select the "Vehicle configuration" menu
then "Memorised speeds". )Choose the speed setting you want tomodify then select "Modify speed".)Enter the desired speed and press confirm
to save the modifications.

105
4
Driving
that the sensors are not covered with mud, ice or snow. When reverse gear isengaged, an audible signal (long beep)indicates that the sensors may be dirty. When the vehicle is moving at a speed below 6 mph (10 km/h), cer tain soundsources (motorcycle, lorry, pneumatic
drill, etc.) may trigger the audible signals of the parking sensor system.
In th
e event of a malfunction of
the system, when reverse gear
is en
gaged this warning lamp
is displayed in the instrument panel and/or a
message appears in the screen, accompanied
by an audible signal (short beep).
Contact a PEUGEOT dealer or a qualified
wor
kshop.

Operating fault
The function will be deactivated automatically if a trailer is being towedor a bicycle carrier is fitted (vehicle fitted with a towbar or bicycle carrier recommended by PEUGEOT).




Deactivation / Activation of the
rear parking sensors
The function is deactivated by pressing this switch. The indicator lamp in the switch comes on.
Pressing this switch again reactivates the function. The indicator lamp in the switchgoes off.

107
5
Visibility


Model without AUTO lighting



Model with AUTO lighting



Selection ring for main lighting mode

Turn the ring to position the symbol required
facing the mark.

Li
ghting off.
Automatic illumination of headlamps.


Sidelamps onl
y.

Di
pped or main beam headlamps.

Stalk for switching headlamps

Pull the stalk to switch the lighting between
dipped / main beam headlamps.

In the li
ghting off and sidelamps modes, the driver can switch on the main beam headlamps
temporaril
y ("headlamp flash") by maintaining apull on the stalk.


Displays

Illumination of the corresponding indicator lamp
in the instrument panel confirms the lighting switched on.

110
Visibility
Daytime running lamps
Daytime lighting, compulsory in cer taincountries, which comes on automatically when
the engine is star ted making the vehicle more
visible to other users.
LED lamps
They come on when the engine is star ted.
Depending on the destination country, they are
used for:
- daytime running lamps * in day mode and
sidelamps in night mode (they are brighter
when daytime running lamps),
or
- sidelamps in day and night mode.

*

function that can be set in the vehicle configuration menu.
Thi
s function is assured:


- in countries where it is imposed by
regulations,
by illumination of the dipped beamheadlamps with the sidelamps and number plate lamps; this function cannot be deactivated.

- for other countries where it is provided,
by the use of dedicated lamps (bulbs or
LEDs); this function can be activated or
deactivated via the vehicle configurationmenu.
The lighting control stalk must be placed in the
"0"or "AU TO "
(day mode) position.
Deactivation of the daytime running lamps iseffective after operation of the lighting control
stalk or after the next engine start; activation iseffective immediately.

The instruments and controls
(instrument
panel, multifunction screen, air conditioning control panel, ...) are not illuminated, except
in night mode with manual or automatic
illumination of headlamps.

111
5
Visibility
headlamps on after the vehicle's ignition hasbeen switched off makes the driver's exit easier
when the light is poor.
Manual guide-me-home
lighting

Switching on
)With the ignition off, "flash" the headlamps
using the lighting stalk.
)A fur ther "headlamp flash" switches the
function off.
Switching off
The manual guide-me-home lighting switches
off automatically after a set time.
Parking lamps
Side markers for the vehicle by illumination of
the sidelamps on the traffic side only.) Within one minute of switching off the
ignition, operate the lighting control stalk
up or down depending on the traffic side(for example: when parking on the left;
lighting control stalk upwards; the right hand sidelamps are on).
Manual
guide-me-home lighting is also available from the remote control lighting button (see "Access - Remotecontrol"). This is con
firmed by an audible signal and
illumination of the corresponding direction
indicator warning lamp in the instrument panel.
To switch o
ff the parking lamps, return the
lighting control stalk to the middle position or switch on the ignition.

112
Visibility
The sidelamps and dipped beam headlamps are
switched on automatically, without any action
on the part of the driver, when a low level of external light is detected or in certain cases of activation of the windscreen wipers.
As soon as the brightness returns to a sufficient
level or after the windscreen wipers are switched
o
ff, the lamps are switched off automatically.
Automatic illumination of
headlam
ps
Switching on
)Turn the ring to the "AU TO "position.
Activation of the function is accompanied
b
y a message in the screen.

Switching off
)Turn the ring to another position. Deactivation of the function is accompanied by a message in the screen.



Automatic guide-me-home
lighting
Association with the automatic lighting provides
the guide-me-home lighting with the followingadditional options:


- selection of the lighting duration of 15, 30or 60 seconds,

- automatic activation of guide-me-home lighting when the automatic illumination of
headlamps is in operation.



Operating fault

In the event of a fault with thesunshine sensor, the lighting comes on, this warning lamp
is displayed in the instrument panel and/or a message appears in the screen, accompaniedby an audible signal.
Contact a PEUGEOT dealer or a qualified
workshop.

In fog or snow, the sunshine sensor maydetect sufficient light. In this case, the lighting will not come on automatically. Do not cover the sunshine sensor,coupled with the rain sensor and located in the centre of the windscreenbehind the rear view mirror; theassociated functions would no longer be controlled.


Programming
The duration of the guide-me-home
lighting can be set in the vehicle configuration menu.

117
5
Visibility
Automatic rain sensitive
windscreen wi
pers
The windscreen wipers operate automatically,
without an
y action on the par t of the driver, if
rain is detected (sensor behind the rear view mirror), adapting their speed to the intensity of
the rainfall.

Switching on

Briefly push the control stalkdownwards.
This warning lamp comes on in the
instrument panel and a message is
displayed.Brie
fly push the control stalk
downwards again, or place thecontrol stalk in another position(Int, 1 or 2).
This warning lamp goes off in the instrument
panel and a message is displayed.
Switching off


The automatic rain sensitive windscreenwipers must be reactivated by pushing the control stalk downwards, if theignition has been off for more than one minute.

120
Visibility








Interior mood lighting The dimmed passenger compar tment lighting improves visibility in the vehicle when the light is poor.
Switching on
At night, interior mood light emitting diodes -LEDs (courtesy lamp, instrument panel,footwells, panoramic sunroof...) come onautomatically when the sidelamps are switched on.


Switching off

The interior mood lighting switches off
automatically when the sidelamps areswitched off.


Settings

Illumination of the centre console andpanoramic sunroof can be set from the audiosystem.