2012 MITSUBISHI iMiEV ecu

Seat and restraint systems
2-31
2
Installing a child restraint system using the seat
belt (with emergency/automatic locking mecha-
nism)
N00407300442
With the exception of the driver, the seat belt in all other seat-
ing positions can be converted from normal Emergency Lock-
ing Retractor (ELR) mode to Automatic Locking Retractor
(ALR) mode. This means that when you pull the seat belt fully
out of the retractor, the retractor will switch to its ALR child
restraint installation function. Always use the ALR child
restraint installation function when you install a child restraint
system using the seat belt.
Children 12 years old and under should always be restrained in
the rear seat, whenever possible, although the front passenger
seat belt can also be converted to ALR mode.
Installation1. Place the child restraint system in the rear seating posi-
tion.
2. Route the seat belt through the child restraint system
according to the instructions provided by the child
restraint system manufacturer. Then insert the seat belt
latch plate into the buckle. Make sure you hear a “click”
when you insert the latch plate into the buckle.
WA R N I N G
!
When you install a child restraint system using the
seat belt, always make sure the retractor has been
switched to the ALR child restraint installation
function. The ALR function will keep the child
restraint system tightly secured to the seat.
Failure to convert the retractor to the ALR function
may allow the child restraint system to move for-
ward during sudden braking or an accident, result-
ing in serious injury or death to the child or other
occupants.
BK0140800US.book 31 ページ ２０１１年９月２９日　木曜日　午後３時２８分

2-32 Seat and restraint systems
2
3. To activate the ALR child restraint installation function,
slowly pull the shoulder part of the belt all the way out of
the retractor until it stops. Then let the belt feed back into
the retractor.
4. After the belt has retracted, tug on it. If the belt is in the
ALR function, you will not be able to pull it out. If the
webbing can be pulled out from retractor, the ALR func-
tion has not been activated and you will need to repeat
steps 3 and 4.5. After confirming that the belt is locked, grab the shoulder
part of the belt near the buckle and pull up to remove any
slack from the lap part of the belt allowing the slack to
feed into the retractor. Remember, if the lap belt portion is
not tight, the child restraint system will not be secure. It
may help to put your weight on the child restraint system
and/or push on its seatback while pulling up on the belt
(see illustration).
If your child restraint system requires the use of a tether strap,
fasten the tether strap in accordance with the following proce-
dures.
BK0140800US.book 32 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Seat and restraint systems
2-33
2
6. Open the cover from the tether anchor installation point
by pulling it back with your hand as illustrated below (6).
7. Remove the head restraint from the location in which you
wish to install a child restraint system.
8. Latch the tether strap hook (A) of the child restraint sys-
tem to the tether anchor (B) as illustrated below (8) and
tighten the top tether strap so it is securely fastened.9. Before putting your child in the restraint, push and pull
the restraint in all directions to be sure it is firmly secured.
Do this before each use. If the child restraint system is not
firmly secure, repeat steps 1 through 8.
10. To remove a child restraint system from the vehicle and
deactivate the ALR mode, remove the child from the
restraint. Unlatch the buckle. Then remove the belt from
the restraint and let the belt fully retract.
WA R N I N G
!
Child restraint system tether anchors are designed
only to withstand loads from correctly fitted child
restraint systems. Under no circumstances are they
to be used for adult seat belts, harnesses, for attach-
ing other items, or equipment to the vehicle.
BK0140800US.book 33 ページ ２０１１年９月２９日　木曜日　午後３時２８分

2-42 Seat and restraint systems
2

To ensure that the passenger’s seat occupant classifi-
cation sensor system can correctly sense the weight
being applied to the seat, observe the following
instructions. Failure to follow these instructions can
adversely affect the performance of the passenger’s
airbag system.
• Adjust the seat to the correct position, and sit well
back against the seatback.
Refer to “Front seats” on page 2-3.
• Do not recline the seatback more than necessary.
• Never have more than one person (adult or child)
sitting on the seat.
• Do not place anything between the seat and the
floor console.
• When attaching a child restraint system, secure it
firmly.
• Do not place luggage or other objects on the seat.
• Do not use a seat cover or a cushion.
• Do not modify or replace the seat and seat belt.
• Do not place luggage or other objects under the
seat.
• Do not place and use an electronic device such as a
computer on the seat.
• Do not place heavy objects on the seat or stick
pins, needles, or other objects into it.
• Do not remove the seat cushion skin.
• If any liquid is spilled on the seat, wipe it and dry
the seat immediately.WA R N I N G
!

If the vehicle is involved in a severe impact, have the
SRS sensors inspected by a certified i-MiEV dealer
as soon as possible.
WA R N I N G
!
BK0140800US.book 42 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-5
3
NOTE
Electronic immobilizer is not compatible with commer-
cially available remote starting systems. Use of commer-
cially available remote starting systems may result in
vehicle starting problems and a loss of security protection.

A system failure is suspected when the electric motor
switch is turned to the “START” position, and the electric
motor unit does not start. In such a case, contact a certified
i-MiEV dealer.Replacement keysOnly keys that have been programmed to the vehicle electron-
ics can be used to start the vehicle.
If you lose a key, you can order a key from a certified i-MiEV
dealer by referring to the key number.
To prevent vehicle theft, the ID code for the vehicle keys must
be changed.
Take your vehicle and all remaining keys to a certified i-MiEV
dealer to have your ID code changed.
Additional keysTo add a key, you need to register the ID code to the vehicle.
Registering the ID code can be done by a certified i-MiEV
dealer. Or it can be done by yourself (except for vehicles sold
in Canada).
To register the ID code yourself, follow the “Customer key
programming” procedure below.
If you choose to have a certified i-MiEV dealer register the ID
code, take your vehicle and any remaining keys to a certified i-
MiEV dealer.NOTE
You are provided with 2 keys, but you may add up to 6
more keys.Customer key programming (Except for vehicles
sold in Canada)
N00562200113
You can program new keys to the system if you have two valid
(already registered) keys and blank (not registered) immobi-
lizer key (specially cut for your vehicle at a certified i-MiEV
dealer) by doing the following:
1. Insert the first valid key into the ignition and turn the igni-
tion to the “ON” position for 5 seconds.
2. Turn the ignition to the “LOCK” position and remove the
first key.
3. Within 30 seconds of turning the first key to the “LOCK”
position, insert the second valid key into the ignition and
turn it to the “ON” position. About 10 seconds later, the
immobilizer indicator will start blinking.
CAUTION
!
Do not make any alterations or additions to the
immobilizer system. Alterations or additions could
cause failure of the immobilizer.
BK0140800US.book 5 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-11
3
3. Remove the remote control transmitter from the remote
control transmitter case. Then, open the remote control
transmitter using the method described in step 1.
4. Remove the old battery.5. Install a new battery with the + side (A) down.
6. Close the remote control transmitter firmly.
7. Place the remote control transmitter in the remote control
transmitter case, then securely close the remote control
transmitter case.
8. Check the keyless entry system to see that it works.
NOTE
A certified i-MiEV dealer can replace the battery for you
if you prefer.
CAUTION
!
When the remote control transmitter case is opened,
be careful to keep water, dust, etc. out. Also, do not
touch internal components.
+ side
- side
Coin type battery CR1620
BK0140800US.book 11 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-17
3
NOTE
If you do not open the liftgate immediately after pulling
the handle, the liftgate can not be lifted. If this happens,
pull the handle again and lift the liftgate.

The liftgate cannot be opened when the battery is flat or
disconnected.To closePull the liftgate grip (A) downward as illustrated. Gently push
the upper gate from the outside with enough force so that it is
completely closed. Always ensure the liftgate is securely
closed.
NOTE
Gas struts (B) are installed to support the liftgate.
To prevent damage or faulty operation.
• Do not hold the gas struts when closing the liftgate.
• Also, do not push or pull on the gas struts.
• Do not attach any plastic material, tape, etc., to the gas
struts.
• Do not tie anything, etc., around the gas struts.
• Do not hang any objects on the gas struts.
CAUTION
!
To avoid injuring your hand or arm, do not attempt
to close the liftgate the gate grip (A).

Before starting the vehicle, be sure to confirm that
the liftgate is locked. If the liftgate opens while driv-
ing the vehicle, objects stored in the luggage com-
partment could fall out into the road.
When closing the liftgate, always ensure that every-
body removes their hands and fingers from the
liftgate opening.
CAUTION
!
BK0140800US.book 17 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-39
3 Service brake
N00517500305
Brake pedalOveruse of the brake can cause poor brake response and pre-
mature wear of the brake pads.
Power brakes
N00517600410
Your vehicle is equipped with power brakes for more braking
force with reduced brake pedal effort.
Your brakes are designed to operate at full capacity, even if the
power assist is lost.
If the power assist is lost, the effort needed to press the brake
pedal is greater.
If you should lose the power assist for some reason, the brakes
will still work.
If the power brake unit or either of the two brake hydraulic sys-
tems stop working properly, the rest of the brake system will
still work, but the vehicle will not slow down as quickly.
You will know this has happened if you find you need to
depress the brake pedal down further, or harder when slowing
down or stopping, or if the brake warning light comes on.
WA R N I N G
!
Do not leave any objects near the brake pedal or let
a floor mat slide under it; doing so could prevent the
full pedal stroke that would be necessary in an emer-
gency. Make sure that the pedal can be operated
freely at all times. Make sure the floor mat is
securely held in place.
CAUTION
!
It is important not to drive the vehicle with your foot
resting on the brake pedal when braking is not
required. This practice can result in very high brake
temperatures, premature pad wear, and possible
damage to the brakes.
WA R N I N G
!
Never turn off the electric motor switch while driv-
ing. Doing so will result in a loss of power assist for
the brakes and steering, increasing the effort
required to steer and brake the vehicle.
BK0140800US.book 39 ページ ２０１１年９月２９日　木曜日　午後３時２８分