2012 MERCEDES-BENZ GLK-Class headlamp

daytime running lamps function using the
on-board computer ( Y page 176).XTurn the light switch to c or à .
With the engine running: depending on the
ambient light, the daytime running lamps or
the low-beam headlamps are switched on.
When the low-beam headlamps are
switched on, the L indicator lamp in the
instrument cluster lights up.
It is only possible to activate the high-beam
headlamps if the brightness of the ambient
light is at a low level.
However, the high-beam flasher can always
be used.
If the engine is running and you turn the light
switch to T or L , the manual settings
take precedence over the daytime running
lamps.
Automatic headlamp mode
XTo switch on automatic headlamp
mode: turn the light switch to c or
à .
SmartKey in position 1 in the ignition lock:
the parking lamps are switched on or off
automatically depending on the brightness
of the ambient light.
With the engine running: depending on the
brightness of the ambient light, the daytime
running lamps 10
or the low-beam
headlamps are switched on or off
automatically.
When the low-beam headlamps are
switched on, the L indicator lamp in the
instrument cluster lights up.GWARNING
If the light switch is set to c or à , the
low-beam headlamps will not come on
automatically if it is foggy. This could
endanger you and others. Therefore, turn the
light switch to L in fog.
The automatic headlamp feature is only an
aid. The driver is responsible for the vehicle's
lighting at all times.
Front fog lamps
Only vehicles with front fog lamps have the
fog lamps function.
GWARNING
If you suspect that driving conditions will be
foggy, turn the light switch to L before you
start your journey. Otherwise, your vehicle
may not be visible and you could endanger
yourself and others.
XTo switch on the front fog lamps: turn
the SmartKey in the ignition lock to position
2 or start the engine.XTurn the light switch to L or c or
à .XPress the N button.
The green N indicator lamp in the
instrument cluster lights up.XTo switch off the front fog lamps: press
the N button.
The green N indicator lamp in the
instrument cluster goes out.
Rear fog lamp
XTo switch on the rear fog lamp: turn the
SmartKey in the ignition lock to position 2
or start the engine.XTurn the light switch to L or c or
à .
If the light switch is set to c or à ,
the rear fog lamp only lights up if the low-
beam headlamps are on.10 Only if daytime running lamps have been activated via the on-board computer.104Exterior lightingLights and windshield wipers

XPress the R button.
The yellow R indicator lamp in the
instrument cluster lights up.XTo switch off the rear fog lamp: press the
R button.
The yellow R indicator lamp in the
instrument cluster goes out.
Headlamp cleaning system
The headlamps are cleaned automatically if
the "Wipe with washer fluid" function is
operated ten times while the lights are on and
the engine is running (Y page 113). When you
switch off the ignition, the automatic
headlamp cleaning system is reset and
counting is resumed from 0.
Combination switch
Turn signals
:High-beam headlamps;Right turn signal=High-beam flasher?Left turn signalXTo indicate briefly: press the combination
switch briefly to the pressure point in the
direction of arrow ; or ?.
The corresponding turn signal flashes three
times.XTo indicate: press the combination switch
beyond the pressure point in the direction
of arrow ; or ?.High-beam headlampsXTo switch on the high-beam headlamps:
turn the SmartKey in the ignition lock to
position 2 or start the engine.XTurn the light switch to L or c or
à .XPress the combination switch beyond the
pressure point in the direction of
arrow :.
In the c or à position, the high-
beam headlamps are only switched on
when it is dark and the engine is running.
The K indicator lamp in the instrument
cluster lights up when the high-beam
headlamps are switched on.XTo switch off the high-beam
headlamps: move the combination switch
back to its normal position.
The K indicator lamp in the instrument
cluster goes out.
High-beam flasher
XTo switch on: turn the SmartKey in the
ignition lock to position 1 or 2 or start the
engine.XPull the combination switch in the direction
of arrow =.
Hazard warning lamps
Exterior lighting105Lights and windshield wipersZ

The hazard warning lamps automatically
switch on if:
R an air bag is deployed.
R the vehicle is slowed down severely from a
speed of over 45 mph (70 km/h) and comes
to a halt.XTo switch on the hazard warning lamps:
press button :.
All turn signals flash. If you now switch on
a turn signal using the combination switch,
only the turn signal lamp on the
corresponding side of the vehicle will flash.XTo switch off the hazard warning
lamps: press button :.
The hazard warning lamps are deactivated
automatically if the vehicle returns to a speed
of over 6 mph(10 km/h) after a full
application of the brakes.
i The hazard warning lamps still operate if
the ignition is switched off.
Active light function
The active light function is a system that
moves the headlamps according to the
steering movements of the front wheels. In
this way, relevant areas remain illuminated
while driving. This allows you to recognize
pedestrians, cyclists and animals.
Active: when the lights are switched on.
Cornering light function
The cornering light function improves the
illumination of the road over a wide angle in
the direction you are turning, enabling better
visibility in tight bends, for example. It can
only be activated when the low-beam
headlamps are switched on.
Active: if you are driving at speeds below
25 mph (40 km/h) and switch on the turn
signals or turn the steering wheel.
Not active: if you are driving at speeds above
25 mph (40 km/h) or switch off the turn
signal or turn the steering wheel to the
straight-ahead position.
The cornering light function may remain lit for
a short time, but is automatically switched off
after no more than three minutes.
Headlamps fogged up on the inside
The headlamps may fog up on the inside if
there is high atmospheric humidity.
XDrive with the headlamps switched on.
The level of moisture diminishes,
depending on the length of the journey and
the weather conditions (humidity and
temperature).
If the level of moisture does not diminish:
XHave the headlamps checked at a qualified
specialist workshop.106Exterior lightingLights and windshield wipers

Manual interior lighting controlXTo switch the front interior lighting on/
off: press the c button.XTo switch the rear interior lighting on/
off: press the v button.XTo switch the reading lamps on/off:
press the p button.
Crash-responsive emergency lighting
The interior lighting is activated automatically
if the vehicle is involved in an accident.
XTo switch off the crash-responsive
emergency lighting: press the hazard
warning lamp button.
or
XLock and then unlock the vehicle using the
SmartKey.
Replacing bulbs
Important safety notes
Xenon bulbs
If your vehicle is equipped with Xenon bulbs,
you can recognize this by the following: the
cone of light from the Xenon bulbs moves
from the top to the bottom and back again
when you start the engine. For this to be
observed, the lights must be switched on
before starting the engine.
GDANGER
Xenon bulbs carry a high voltage. You could
get an electric shock and be seriously or even
fatally injured if you touch the electric
contacts on Xenon bulbs. Therefore, never
remove the cover from Xenon bulbs.
Do not change Xenon bulbs yourself, but have
them replaced at a qualified specialist
workshop which has the necessary specialist
knowledge and tools to carry out the work
required.
Mercedes-Benz recommends that you use an
authorized Mercedes-Benz Center for this
purpose. In particular, work relevant to safety
or on safety-related systems must be carried
out at a qualified specialist workshop.
Bulbs and lamps are an important aspect of
vehicle safety. You must therefore make sure
that these function correctly at all times.
Have the headlamp setting checked regularly.
Other bulbs
There are bulbs other than the Xenon bulbs
that you cannot replace. Replace only the
bulbs listed (Y page 109). Have the bulbs that
you cannot replace yourself changed at a
qualified specialist workshop.
Mercedes-Benz recommends that you use an
authorized Mercedes-Benz Center for this
purpose. In particular, work relevant to safety
or on safety-related systems must be carried
out at a qualified specialist workshop.
If you require assistance changing bulbs,
consult a qualified specialist workshop.
Do not touch the glass tube of new bulbs with
your bare hands. Even minor contamination
can burn into the glass surface and reduce
the service life of the bulbs. Always use a lint-
free cloth or only touch the base of the bulb
when installing.
Only use bulbs of the correct type.
If the new bulb still does not light up, consult
a qualified specialist workshop.
Bulbs and lamps are an important aspect of
vehicle safety. You must therefore make sure
that these function correctly at all times.
Have the headlamp setting checked regularly.
GWARNING
Bulbs and lamps can be very hot. You should
therefore allow them to cool down before you
change them. Otherwise, you could be burned
if you touch them.
Keep bulbs out of the reach of children.
Otherwise, they could damage the bulbs, for
example, and injure themselves.
108Replacing bulbsLights and windshield wipers

Never use a bulb which has been dropped.
Such a bulb may break or even explode and
injure you.
Halogen bulbs are pressurized and can
explode when you change them, particularly
if they are very hot. You should therefore wear
eye protection and gloves when you are
changing them.
Overview: changing bulbs/bulb types
You can change the following bulbs. The bulb
type can be found in the legend.
Halogen headlamps
:Turn signal lamp/side marker lamp:
WY 5 W;Turn signal lamp: PY 21 W=High-beam headlamp: H7 55 W?Parking lamp/standing lamp: W 5 WALow-beam headlamp: H7 55 W
Bi-Xenon headlamps
:Turn signal lamp/side marker lamp:
WY 5 W;Turn signal lamp: PY 21 W=Cornering lamp: H7 55 W?Parking lamp/standing lamp: W 5 W
Tail lamp with/without LED
:Tail lamp/brake lamp: P 21 W;Turn signal lamp: PY 21 W=Backup lamp: P 21 W or W 16 W 11?Tail lamp/rear fog lamp: P 21 WASide marker lamp: W 3 W11
Vehicles without LED turn signal lamps (W 16 W)/vehicles with LED turn signal lamps (P 21 W).Replacing bulbs109Lights and windshield wipersZ

License plate lamp
:License plate lamp: W 5 W
Changing the front bulbs
Removing/installing the headlamp
cover
You must remove the headlamp cover in the
engine compartment before you can replace
the bulbs in the headlamp.
XTo remove: press retaining clip : in the
direction of the arrow.XPull cover ; forward underneath
cover = and remove.XTo install: slide cover ; under cover =.
Connect the two covers by inserting the
tongue into the groove.XPress cover ; until retaining clip :
engages.Removing/attaching the washer fluid
reservoir
You must remove the washer fluid reservoir
from the engine compartment before you can
replace the bulbs in the left-hand headlamp.
XTo detach: turn catch ; counter-
clockwise.XSwing washer fluid reservoir : far enough
to the side to allow the bulbs of the
headlamp to be replaced.XTo attach: swing back washer fluid
reservoir :.XTurn catch ; clockwise.
Low-beam headlamps (halogen
headlamps)
XSwitch off the lights.XOpen the hood.XRemove the headlamp cover (Y page 110).XLeft-hand headlamp: detach the washer
fluid reservoir ( Y page 110).110Replacing bulbsLights and windshield wipers

XTurn housing cover : counter-clockwise
and pull it out.XPull connector ; from bulb ?.XUnclip retaining spring = and fold it down.XPull out bulb ?.XInsert the new bulb.XClip retaining spring = back in.XAttach connector ; to bulb ?.XAttach housing cover : and turn it
clockwise until it engages.XLeft-hand headlamp: fasten the washer
fluid reservoir ( Y page 110).XInstall the headlamp cover ( Y page 110).
High-beam headlamps (halogen
headlamps)
XSwitch off the lights.XOpen the hood.XRemove the headlamp cover (Y page 110).XLeft-hand headlamp: detach the washer
fluid reservoir ( Y page 110).XTurn housing cover : counter-clockwise
and pull it out.XPress the handle of bulb holder ; in the
direction of the arrow until bulb holder ;
is released.XTake out the handle with bulb holder ;.XTake the bulb out of bulb holder ;.XInsert the new bulb into bulb holder ;.
Lug = of the bulb must be pointing
upward.XInsert bulb holder ;.XPush the handle of bulb holder ; in the
opposite direction from the arrow until
holder ; engages.XAlign housing cover : and turn it
clockwise until it engages.XLeft-hand headlamp: fasten the washer
fluid reservoir ( Y page 110).XInstall the headlamp cover ( Y page 110).
Parking lamp/standing lamp
XSwitch off the lights.XOpen the hood.XRemove the headlamp cover (Y page 110).XLeft-hand headlamp: detach the washer
fluid reservoir ( Y page 110).XTurn housing cover : counter-clockwise
and pull it out.XPull out bulb holder ;.Replacing bulbs111Lights and windshield wipersZ

XTake the bulb out of bulb holder ;.XInsert the new bulb into bulb holder ;.XInsert bulb holder ;.XAlign housing cover : and turn it
clockwise until it engages.XLeft-hand headlamp: fasten the washer
fluid reservoir ( Y page 110).XInstall the headlamp cover ( Y page 110).
Turn signal lamps/side marker lamps
XSwitch off the lights.XOpen the hood.XRemove the headlamp cover (Y page 110).XLeft-hand headlamp: detach the washer
fluid reservoir ( Y page 110).XTurn bulb holder : or ; counter-
clockwise and pull it out.XWY 5 W (turn signal lamp and side marker
lamp): remove the bulb from bulb
holder :.XPY 21 W (turn signal lamp): turn the bulb
counter-clockwise, applying slight
pressure, and remove it from bulb
holder ;.XWY 5 W (turn signal lamp and side marker
lamp): insert the new bulb into bulb
holder :.XPY 21 W (turn signal lamp): insert the new
bulb into bulb holder ; and turn it
clockwise while applying slight pressure.XInsert bulb holder : or ; and turn it
clockwise.XLeft-hand headlamp: fasten the washer
fluid reservoir ( Y page 110).XInstall the headlamp cover ( Y page 110).
Changing the rear bulbs
Opening and closing the side trim
panels
You must open the side trim panel in the
cargo compartment before you can change
the bulbs in the tail lamps.
Left-hand side trim panel
Right-hand side trim panel
XTo open: turn release knob : 90° in the
direction of the arrow and remove side trim
panel ;.XTo close: insert side trim panel ; and turn
release knob : 90° in the opposite
direction to the arrow.112Replacing bulbsLights and windshield wipers