2012 MERCEDES-BENZ G-Class Door

Problem Possible causes/consequences and
M Solutions7
The red seat belt
warning lamp lights up
after the engine starts,
as soon as the driver's
or the front-passenger
door is closed.
G
Risk of injury
The driver or front passenger has not fastened their seat belt.
X Fasten your seat belt ( Y page 41).
The warning lamp goes out. G
Risk of injury
There are objects on the front-passenger seat.
X Remove the objects from the front-passenger seat and stow
them in a secure place.
The warning lamp goes out. 7
The red seat belt
warning lamp flashes
and an intermittent
audible warning
sounds.
G
Risk of injury
The driver or front passenger has not fastened their seat belt. In
addition, you
are driving faster than 15 mph (25 km/h) or you have
briefly driven faster than 15 mph (25 km/h).
X Fasten your seat belt ( Y page 41).
The warning
lamp goes out and the intermittent audible warning
ceases. G
Risk of injury
There are objects on the front-passenger seat. In addition, you are
driving faster than 15 mph (25 km/h ) or you have briefly driven
faster than 15 mph (25 km/h

).
X Remove the objects from the front-passenger seat and stow
them in a secure place.
The warning

lamp goes out and the intermittent audible warning
ceases. Warning and indicator lamps in the instrument cluster
179
On-board computer and displays Z

Tires
Problem Possible causes/consequences and
M Solutions
h
USA only:
The
yellow

tire pressure
monitor warning lamp
(pressure loss/
malfunction) is lit.
Canada only:
The yellow tire pressure
monitor warning lamp
(pressure loss) is lit. G
Risk of accident
The tire pressure monitor has detected a loss of pressure in at
least one of the tires.
X Stop
the vehicle without making any sudden steering or braking
maneuvers. Pay

attention to the traffic conditions as you do so.
X Observe the additional display messages in the multifunction
display.
X Check the tire pressure. If necessary, correct the tire pressure
(Y page 249).
X If necessary, change a wheel ( Y page 265).h
USA only:
The
yellow

tire pressure
monitor warning lamp
(pressure loss/
malfunction) flashes for
60 seconds and then
remains lit. The tire pressure monitor is defective.
X
Observe the additional display messages in the multifunction
display.
X Visit a qualified specialist workshop. G
WARNING
Each tire, including the spare (if provided), should be checked at least every two weeks when
cold and inflated to the pressure recommended by the vehicle manufacturer on the Tire and
Loading Information placard on the driver's door B-pillar or, if available, the tire pressure label
on

the inside of the fuel filler flap. If your vehicle has tires of a different size than the size indicated
on the Tire and Loading Information placard or the tire pressure label, you should determine the
proper tire pressure for those tires.
As an added safety feature, your vehicle has been equipped with a tire pressure monitoring
system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires are
significantly underinflated. Accordingly, when the low tire pressure telltale illuminates, you should
stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving
on a significantly underinflated tire causes the tire to overheat and can lead to tire failure.
Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling
and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance,
and it is the driver's responsibility to maintain correct tire pressure, even if underinflation has
not reached the level to trigger illumination of the TPMS low tire pressure telltale.
USA only:
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the
system is not operating properly. The TPMS malfunction indicator is combined with the low tire
pressure telltale. When the system detects a malfunction, the telltale will flash for approximately
1 minute and then remain continuously illuminated. This sequence will be repeated every time Warning and indicator lamps in the instrument cluster
185
On-board computer and displays
Z

Useful information
i This Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's
Manual. Country-specific differences are
possible. Please
note that your vehicle may
not be equipped with all features
described. This also applies to safety-
related systems and functions.
i Please read the information on qualified
specialist workshops (Y page 20). Loading guidelines
G
WARNING
Always
fasten items being carried as securely
as possible using cargo tie-down rings and
fastening materials

appropriate for the weight
and size of the load.
In an accident, during hard braking or sudden
maneuvers, loose items will be thrown around
inside the vehicle. This can cause injury to
vehicle occupants unless the items are
securely fastened in the vehicle.
To help avoid personal injury during a collision
or sudden maneuver, exercise care when
transporting cargo. Do not pile luggage or
cargo higher than the seat backrests.
Never drive a vehicle with the tailgate open.
Deadly carbon monoxide (CO) gases may
enter vehicle interior resulting in
unconsciousness and death.
The handling characteristics of a laden
vehicle are dependent on the distribution of
the load within the vehicle. You should
therefore load your vehicle as shown in the
illustrations. The
gross vehicle weight (GVW) is the vehicle
weight including fuel, vehicle tool kit, spare
wheel, installed accessories, vehicle
occupants and luggage/cargo.
The gross load limit and the gross vehicle
weight rating (GVWR) for your vehicle must
never be exceeded. The gross load limit and
the GVWR are specified on the vehicle
identification plate on the B-pillar of the
driver's door ( Y page 271).
The load

must also be distributed so that the
weight on each axle never exceeds the gross
axle weight rating (GAWR) for the front and
rear axles. The specifications for GVWR and
GAWR are on the vehicle identification plate
on the B-pillar of the driver's door
(Y page 271).
Further information can be found in the
"Loading the vehicle" section ( Y page 252).
Observe the following notes when
transporting a load:
R position heavy loads as far forwards as
possible and as low down in the cargo
compartment as possible.
i Transport loads when possible in the
cargo compartment. You should only use
the cargo compartment enlargement if the
load does not fit in the cargo compartment.
R always place the load against the front or
rear seat backrests.188
Loading guidelines
Stowing and features

For safety reasons, the rear seat bench must
only be adjusted when the vehicle is
stationary.
Never drive a vehicle with the tailgate open.
Deadly carbon monoxide (CO) gases may
enter vehicle interior resulting in
unconsciousness and death.
! Ensure that you remove all containers
from the cup holder in the rear before
folding the seat backrest and the seat
cushion of the rear bench seat forwards.
The left-hand and right-hand rear seats can
be folded down to increase the cargo
compartment capacity. The following
changes are possible:
R fold the seat backrests forward
R fold the rear bench seat back fully.
Folding the seat backrest forward :
Seat backrest release lever
; Rear bench seat release lever
i Open the rear doors. This allows you
better access to release lever :.
X Remove the center head restraint
(Y page 78).
X Pull release lever :.
The corresponding seat backrest is
released.
X Fold the seat backrest forward until it
engages. Folding the seat backrest back X
Pull release lever : and fold the seat
backrest backwards.
! Make sure that the seat belt does not
become trapped

when folding the rear seat
backrest back. Otherwise, it could be
damaged.
X Fold the seat backrest back until it engages
audibly in the seat catch.
X Install the head restraints (Y page 78).
Folding the rear bench seat forward X
Fold the backrest forwards (
Y page 191).
X Pull release lever ;.
The corresponding rear bench seat is
released.
X Fold the rear bench seat forward until it
engages.
Folding the rear bench seat into an
upright position X
Fold back the rear bench seat backrest
until it engages audibly in the seat catch.
X Fold the backrest backwards
( Y page 191).
X Install the head restraints (Y page 78). G
WARNING
Make sure that the rear bench seat and front
seat backrest are correctly engaged in
position.
If the seat backrests or rear bench seat are
not fully engaged and the following occurs:
R sharp braking
R a sudden change of direction
R an accident
the seat

backrests or rear bench seat may fold
forwards and instead of being restrained by
the seats as intended you could be injured by
them. Occupants could then also be injured
in the event of an accident, e.g. by objects Stowage areas
191
Stowing and features
Z

being thrown forwards from the cargo
compartment.
Securing cargo
Important safety notes G
WARNING
Distribute the load on the cargo tie down rings
evenly.
Otherwise, vehicle occupants could be
injured by

objects being thrown around if you:
R brake sharply
R change direction suddenly
R are involved in an accident
Please observe the loading guidelines.
Observe the following notes on securing
loads:
R secure the load using the cargo tie down
rings.
R do not use elastic straps or nets to secure
a load, as these are only intended as an
anti-slip protection for light loads.
R do not route tie downs across sharp edges
or corners.
R pad sharp edges for protection.
R only use tie downs that have been checked
in accordance with applicable standards,
e.g. lashing nets or lashing straps.
R fill the spaces between the load and the
cargo compartment walls and the wheel
mountings in a form-locking way. Only use
dimensionally stable transportation aids
for this, such as chocks, wooden fixings or
padding.
Cargo tie down rings in the cargo
compartment There are four cargo tie down rings in the
cargo compartment mounted at the sides. Cargo compartment cover
Important safety notes !
When loading

the vehicle, make sure that
you do not stack the load in the cargo
compartment higher than the lower edge of
the side windows. Do not place heavy
objects on top of the cargo compartment
cover.
The cargo compartment cover is located
behind the rear bench seat backrest.
Opening and closing the cargo
compartment cover X
To open:
pull cargo compartment
cover : back

and clip it into the retainers
on the left and right of the rear door.
X To close: unclip cargo compartment
cover : and guide it forwards until it is
completely rolled up. 192
Stowage areas
Stowing and features

Ashtray
Ashtray in the cockpit X
To open: press cover ? and then release
it.
Ashtray : folds out.
X To remove insert: make sure that the
vehicle is secured against rolling away by
applying the parking brake.
X Move the selector lever to N.
X Move slide knob = to the right, so that
insert ; is released.
X Pull insert ; upwards and remove it.
X To re-install the insert: press insert ;
into the holder until it engages.
X To close: press cover ? until it engages.
Ashtray in the rear compartment An ashtray is located in each of the rear
doors. X
To open: fold cover ;
out in the direction
of the arrow.
X To remove the insert: press retaining
lug : and

pull insert = upwards and out.
X To re-install the insert: replace insert =
from above.
X To close: close cover ; fully. Cigarette lighter
G
WARNING
When leaving the vehicle, always remove the
SmartKey from the ignition lock. Always take
the SmartKey with you and lock the vehicle.
Do not leave children unattended in the
vehicle, even if they are secured in a child
restraint system, or with access to an
unlocked vehicle. A child's unsupervised
access to

a vehicle could result in an accident
and/or serious personal injury. The children
could:
R injure themselves on parts of the vehicle
R be seriously or fatally injured through
excessive exposure to extreme heat or cold
R injure themselves or cause an accident with
vehicle equipment that can be operated
even if the SmartKey is removed from the
ignition lock or removed from the vehicle,
such as seat adjustment, steering wheel
adjustment, or the memory function
If children open a door, they could injure other
persons or get out of the vehicle and injure
themselves or be injured by following traffic.
Do not expose the child restraint system to
direct sunlight. The child restraint system's
metal parts, for example, could become very
hot, and the child could be burned on these
parts. G
WARNING
Never touch the heating element or sides of
the lighter; they are extremely hot. Hold the
knob only. Features
195
Stowing and features
Z

Make sure any children traveling with you do
not injure themselves or start a fire with the
hot cigarette lighter.
! The 12 V socket in the cigarette lighter
can be used for accessories (up to a
maximum of 180 W), as long as they have
the standard socket type for cigarette
lighters. Note that the socket in the
cigarette lighter can be damaged when
connecting accessories, for example by
frequent insertion and removal or by
sockets that
do not fit correctly. A damaged
socket can cause the cigarette lighter to
stop working. X
Press cover
; and then release it.
The ashtray and cigarette lighter : fold
out.
X Press in cigarette lighter :.
Cigarette lighter : will pop out
automatically when the heating element is
red-hot. 12 V sockets
Points to observe before use !
If you are simultaneously using all three
sockets in the vehicle, make sure that you
do not exceed the maximum current draw
of 45 A. Otherwise, you will overload the
fuses.
The sockets

can be used for accessories with
a maximum power consumption of 180 W (15
A), e.g. lamps or chargers for mobile phones. If you use the sockets for long periods when
the engine is switched off, the battery may
discharge.
X
Turn the SmartKey to position 2 in the
ignition lock.
Socket in the front-passenger footwell X
Lift up the cover of the socket.
The
cigarette lighter socket can be also used
(Y page 195). This is the case even if the
SmartKey has

been removed from the ignition
lock.
Socket in the rear compartment The socket is located on the center console
in the rear compartment.
X
Lift up the cover of the socket.
Socket in the cargo compartment The socket is located in the cargo
compartment on the left-hand side, when
viewed in the direction of travel, next to the
rear door.196
Features
Stowing and features

R
USA: Response Center at
1-888-990-9007
R Canada: Customer Service at
1-888-923-8367
You will be asked for your password.
X Return to your vehicle at the time arranged
with the Response Center.
X Press and hold the release button on the
rear door handle for at least 20 seconds
until the indicator lamp in the SOS button
(Y page 199) begins flashing.
The Connecting Call message appears
on the multifunction display.
Alternatively, the vehicle can also be opened
via the Internet in the "Owners Online"
section using your ID number and
password 17
.
i Vehicle remote
unlocking is only possible
if the corresponding mobile phone network
is accessible.
The SOS button flashes and the
Connecting Call message appears in the
multifunction display to confirm that the
command for vehicle remote unlocking has
been received.
If you press the rear door's locking cylinder
for more than 20 seconds before receiving
authorization for remote unlocking, you
must wait 15 minutes before you can press
the rear door's locking cylinder again.
Service for recovering a stolen vehicle If your vehicle has been stolen:
X
Contact the police.
The police

will issue an incident report. This
report has a number.
X Forward this number to the Response
Center together with your PIN.
The Response Center will then attempt to
covertly contact the mbrace system. The
Response Center contacts you and the
local law enforcement authority if the
vehicle is located. However, only the law enforcement is informed of the location of
the vehicle.
i If the anti-theft alarm system remains
activated for longer than thirty seconds,
mbrace is automatically connected to the
Response Center. Brush guard (USA only)
G
WARNING
The brush guard is designed solely to enhance
the appearance of the vehicle and help
protect grille and headlamps from minor
mishaps, either on or off road.
Since the

safety characteristics are limited in
the event of an accident, brush guard are not
intended to prevent injury or damage in the
event of an accident. Also observe state and
local regulations on installation and use.
Raise and lower the brush guard in an open
space with plenty of room. Example: G 55 AMG with brush guard
!
Only drive

when the brush guard is folded
up and locked.
Only fold down the brush guard to replace
a bulb, for example.
17 USA only. Features
203
Stowing and features Z