2012 MAZDA MODEL 2 oil dipstick

Black plate (245,1)
Engine Compartment Overview
Battery Fuse block
Engine oil dipstick
Engine oil-filler cap Engine coolant reservoir
Windshield washer fluid reservoir
Automatic transaxle
fluid-level dipstick (only
for automatic transaxle)
Brake/Clutch fluid
reservoir
Cooling system cap
Maintenance and Care
Owner Maintenance
8-11
Mazda2_8CC7-EA-11H_Edition2 Page245
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (247,1)
4. Pull out the dipstick, wipe it clean, andreinsert it fully.
Full
OK
Low
5. Pull it out again and examine the level.
The level is normal if it is between
Low and Full.
If it is near or below Low, add enough
oil to bring the level to Full.
CAUTION
Do not add engine oil over Full. This
may cause engine damage.
6. Make sure the O-ring on the dipstick is positioned properly before reinserting
the dipstick.
Engine Coolant
qInspecting Coolant Level
WARNING
Do not use a match or live flame in the
engine compartment. DO NOT ADD
COOLANT WHEN THE ENGINE IS HOT:
A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become
very hot. You could be burned.
Carefully inspect the engine coolant
in the coolant reservoir, but do not
open it.
Switch the ignition to off and
make sure the fan is not running before
attempting to work near the cooling
fan: Working near the cooling fan when it
is running is dangerous. The fan
could continue running indefinitely
even if the engine has stopped and
the engine compartment temperature
is high. You could be hit by the fan
and seriously injured.
Do not remove the cooling
system cap when the engine and
radiator are hot: When the engine and radiator are
hot, scalding coolant and steam may
shoot out under pressure and cause
serious injury.
NOTE
Changing the coolant should be done by an
Authorized Mazda Dealer.
Maintenance and Care
Owner Maintenance
8-13
Mazda2_8CC7-EA-11H_Edition2 Page247
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (336,1)
Specifications
qEngine
Item Specification
Type DOHC-16V in-line, 4-cylinder
Bore × Stroke 78.0 × 78.4 mm (3.07 × 3.09 in)
Displacement 1,498 ml (1,498 cc, 91.4 cu in)
Compression ratio 10.0
qElectrical System
Item Classification
Battery 12V-40AH/5HR, 12V-52AH/5HR
Spark-plug number DENSO SK16PR-E13
Spark-plug gap 1.2―1.3 mm (0.047 ―0.051 in)
CAUTION
When cleaning the iridium plugs, do not use a wire brush. The fine particulate
coating on the iridium alloy and platinum tips could be damaged.
q Lubricant Quality
Lubricant type and classification
Engine oil Refer to Recommended Oil on page 8-12.
Manual transaxle oil API Service GL-4
SAE 75W-80
Automatic transaxle fluid Mazda Genuine ATF M-V
Brake/Clutch fluid SAE J1703 or FMVSS116 DOT-3
q Capacities
(Approximate Quantities)
Item Capacity
Engine oil With oil filter replacement 3.9 L (4.1 US qt, 3.4 Imp qt)
Without oil filter replacement 3.7 L (3.9 US qt, 3.3 Imp qt)
Coolant Manual transaxle 5.1 L (5.4 US qt, 4.5 Imp qt)
Automatic transaxle 5.4 L (5.7 US qt, 4.8 Imp qt)
Manual transaxle oil 2.91 L (3.07 US qt, 2.56 Imp qt)
Automatic transaxle fluid 7.0 L (7.4 US qt, 6.2 Imp qt)
Fuel tank 42.8 L (11.3 US gal, 9.41 Imp gal)
Check oil and fluid levels with dipsticks or reservoir gauges.
10-4
Specifications
Mazda2_8CC7-EA-11H_Edition2 Page336
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H