2012 MAZDA MODEL 2 turn signal

Black plate (180,1)
Strong signal noise
This occurs very close to a transmitter
tower. The broadcast signals are
extremely strong, so the result is noise and
sound breakup at the radio receiver.
Station drift noise
When a vehicle reaches the area of two
strong stations broadcasting at similar
frequencies, the original station may be
temporarily lost and the second station
picked up. At this time there will be some
noise from this disturbance.
Station 2
88.3 MHz
Station 1
88.1 MHz
q
Operating Tips for CD Player
Condensation phenomenon
Immediately after turning on the heater
when the vehicle is cold, the CD or
optical components (prism and lens) in the
CD player may become clouded with
condensation. At this time, the CD will
eject immediately when placed in the unit.
A clouded CD can be corrected simply by
wiping it with a soft cloth. Clouded
optical components will clear naturally in
about an hour. Wait for normal operation
to return before attempting to use the unit.
Handling the CD player
The following precautions should be
observed.
lDo not spill any liquid on the audio
system.
lDo not insert any objects, other than
CDs, into the slot.
6-12
Interior Comfort
Audio System
Mazda2_8CC7-EA-11H_Edition2 Page180
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (194,1)
qOperating the Radio
Display
Band selector button Scan button
Tuning button Channel preset buttonsAuto memory button
Radio ON
Press a band selector button (
)to
turn the radio on.
Band selection
Successively pressing the band selector
button (
) switches the bands as
follows: FM1 →FM2 →AM.
The selected mode will be indicated. If
FM stereo is being received, “ST ”will be
displayed.
NOTE
If the FM broadcast signal becomes weak,
reception automatically changes from
STEREO to MONO for reduced noise, and the
“ ST ”indicator will go out.
Tuning
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
NOTE
If the power supply is interrupted (fuse blows
or the battery is disconnected), the preset
channels will be erased.
Manual tuning
Select the station by pressing the tuning
button (
,) lightly.
Seek tuning
Automatic search for radio stations starts
when the tuning button (
,) is pressed
until a beep sound is heard. The search
stops when a station is found.
6-26
Interior Comfort
Audio System
Mazda2_8CC7-EA-11H_Edition2 Page194
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (212,1)
Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.
Depress the hazard warning flasher and all
the turn signals will flash.
NOTE
lThe turn signals do not work when the
hazard warning lights are on.
lCheck local regulations about the use of
hazard warning lights while the vehicle is
being towed to verify that it is not in
violation of the law.
7-2
In Case of an Emergency
Parking in an Emergency
Mazda2_8CC7-EA-11H_Edition2 Page212
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (217,1)
NOTElMake sure the jack is well lubricated before
using it.
(With Tire Pressure Monitoring System)
lBe sure to register the tire pressure sensor
ID signal code whenever tires or wheels are
changed (page 5-27).
1. Park on a level surface off the right-of- way and firmly set the parking brake.
2. Put a vehicle with an automatic transaxle in Park (P), a manual
transaxle in Reverse (R) or 1, and turn
off the engine.
3. Turn on the hazard warning flasher.
4. Have everyone get out of the vehicle and away from the vehicle and traffic.
5. Remove the jack, tool bag, and spare tire (page 7-3).
6. Block the wheel diagonally opposite the flat tire. When blocking a wheel,
place a tire block both in front and
behind the tire.
NOTE
When blocking a tire, use rocks or wood blocks
of sufficient size if possible to hold the tire in
place.
qRemoving a Flat Tire
1. If your vehicle is equipped with a
wheel cover, pry off the wheel cover
with the beveled end of the jack lever.
NOTE
Force the end of the jack lever firmly between
wheel and cover, or removal will be difficult.
CAUTION
There is a valve-stem mark inside the
wheel cover. When installing the
wheel cover, align this mark with the
tire's valve stem.
Damage could occur during
installation if the wheel cover is not
properly aligned.
In Case of an Emergency
Flat Tire
7-7
Mazda2_8CC7-EA-11H_Edition2 Page217
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (266,1)
Light Bulbs
Headlights
Front turn signal lights Overhead light
Side turn signal lights
Parking lights/Front side-
marker lights
Fog lights
High-mount brake light
Reverse lights Luggage compartment light
Rear turn signal lights
Some models.
License plate light
Brake lights/Taillights
(Rear side-marker lights)
8-32
Maintenance and Care
Owner Maintenance
Mazda2_8CC7-EA-11H_Edition2 Page266
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (269,1)
3. Disconnect the electrical connectorfrom the bulb by pressing the tab on
the connector with your finger and
pulling the connector.
4. Turn the bulb assemblycounterclockwise and remove it.
5. Install the new bulb in the reverse order
of removal.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
Front turn signal lights
1. Make sure the ignition is switched off and the headlight switch is off.
2. Lift the hood.
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Remove the bulb by pushing it in slightly and turning it
counterclockwise.
5. Install the new bulb in the reverse orderof removal.
Parking lights/Front side-marker lights
1. Make sure the headlight switch is off.
2. If you are changing the right bulb, startthe engine, turn the steering wheel all
the way to the left, and turn off the
engine. If you are changing the left
bulb, turn the steering wheel to the
right.
Maintenance and Care
Owner Maintenance
8-35
Mazda2_8CC7-EA-11H_Edition2 Page269
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (270,1)
3. Turn the screws and the center sectionof the plastic retainers
counterclockwise and remove them,
then partially peel back the mudguard.
Removal
Installation
4. Turn the socket and bulb assembly counterclockwise and remove it.
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse order of removal.
Side turn signal lights
1. Make sure the ignition is switched offand the headlight switch is off.
2. Slide the unit as shown in the figure to remove it.
3. Detach the electrical connector fromthe unit by pulling it outward.
4. Install the new side turn signal unit inthe reverse order of removal.
NOTE
Bulb replacement is not possible because it is
built into the unit. Replace the unit.
8-36
Maintenance and Care
Owner Maintenance
Mazda2_8CC7-EA-11H_Edition2 Page270
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H

Black plate (271,1)
Brake lights/Taillights (Rear side
marker lights)/Rear turn signal lights/
Reverse lights
1. Make sure the ignition is switched offand the headlight switch is off.
2. Turn the bolts counterclockwise and remove them.
3. Pull the unit rearward to remove it.
4. Turn the socket and bulb assemblycounterclockwise and remove it.
5. Disconnect the bulb from the socket. Brake lights/Taillights (Rear side
marker lights)
Rear turn signal lights
Reverse lights
6. Install the new bulb in the reverse order
of removal.
Maintenance and Care
Owner Maintenance
8-37
Mazda2_8CC7-EA-11H_Edition2 Page271
Monday, September 26 2011 1:55 PM
Form No.8CC7-EA-11H