2012 Lexus IS220d lock

455
4-3. Do-it-yourself maintenance
4
Maintenance and care
IS250/220d/200d_EEUnplug the connector while
pulling the lock release.
Headlight high beams (vehicles with halogen headlights)
Release the lock and remove
the cover.
Turn the bulb base counter-
clockwise.
Unplug the connector while
depressing the lock release.
STEP3
STEP1
STEP2
STEP3

456
4-3. Do-it-yourself maintenance
IS250/220d/200d_EEHeadlight high beams (vehicles with discharge headlights)
Turn the cover counterclock-
wise and remove it.
Turn the bulb base counter-
clockwise.
Unplug the connector while
pulling the lock release.
STEP1
STEP2
STEP3

457
4-3. Do-it-yourself maintenance
4
Maintenance and care
IS250/220d/200d_EEFront position lights (vehicles with halogen headlights)
Release the lock and remove
the cover.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
STEP1
STEP2
STEP3

458
4-3. Do-it-yourself maintenance
IS250/220d/200d_EEBack-up lights and rear fog lights
Open the trunk door and
remove the trunk panel cover
clips.
Partly remove the trunk panel
cover and turn the bulb bases
counterclockwise.
Rear fog light
Back-up light
Remove the light bulb.
Rear fog light
Back-up light
Rear turn signal lights
Open the trunk door and
remove the cover.
STEP1
STEP2
STEP3
STEP1

459
4-3. Do-it-yourself maintenance
4
Maintenance and care
IS250/220d/200d_EETurn the bulb base counter-
clockwise.
Remove the light bulb.
Bulbs other than the above
If any of the bulbs listed below has burnt out, have it replaced by
any authorized Lexus dealer or repairer, or another duly quali-
fied and equipped professional.
Headlight high and low beams (discharge bulbs)
Front fog lights
Front turn signal lights
Side turn signal lights
Stop/tail lights
Tail lights
High mounted stoplight
License plate lights
Daytime running lights
Front position lights (vehicles with discharge headlights)
STEP2
STEP3

461
4-3. Do-it-yourself maintenance
4
Maintenance and care
IS250/220d/200d_EE
CAUTION
Replacing light bulbs
Turn off the headlights. Do not attempt to replace the bulb immediately
after turning off the headlights.
The bulbs become very hot and may cause burns.
Do not touch the glass portion of the light bulb with bare hands. Hold the
bulb by the plastic or metal portion.
If the bulb is scratched or dropped it may blow out or crack.
Fully install light bulbs and any parts used to secure them. Failing to do so
may result in heat damage, fire, or water entering the headlight unit. This
may damage the headlights or cause condensation to build up on the lens.
Discharge headlights (if equipped)
Contact any authorized Lexus dealer or repairer, or another duly qualified
and equipped professional, before replacing discharge headlights (includ-
ing light bulbs).
Do not touch the high-intensity discharge headlight’s high voltage socket
when the headlights are turned on.
An extremely high voltage of 20000 V will be discharged and could result
in serious injury or death by electric shock.
Do not attempt to take apart or repair the low beam discharge headlight
bulbs, connectors, power supply circuits, or related components.
Doing so could result in electric shock and serious injury or death.
To prevent damage or fire
Make sure bulbs are fully seated and locked.

5
463
5-1. Essential information
When trouble arises
IS250/220d/200d_EE
Towing with a wheel lift-type truck
From the front
Vehicles with an automatic
transmission: Use a towing
dolly under the rear wheels.
Vehicles with a manual trans-
mission: We recommend to use
a towing dolly under the rear
wheels.
When not using a towing dolly,
release the parking brake and
shift the shift lever to N.
From the rear
Switch to ACCESSORY mode
so that the steering wheel is
unlocked.
NOTICE
To prevent causing serious damage to the transmission
(vehicles with an automatic transmission)
Never tow this vehicle from the front with the rear wheels on the ground.

464
5-1. Essential information
IS250/220d/200d_EE
Using a flat bed truck
If your Lexus is transported by
a flat bed truck, it should be
tied down at the locations
shown in the illustration.
If you use chains or cables to tie
down your vehicle, the angles
shaded in black must be 45.
Do not overly tighten the tie
downs or the vehicle may be
damaged.
NOTICE
To prevent damaging the vehicle
Do not tow the vehicle from the rear with the “ENGINE START STOP”
switch OFF.
The steering lock mechanism is not strong enough to hold the front wheels
straight.
When raising the vehicle, ensure adequate ground clearance for towing at
the opposite end of the raised vehicle. Without adequate clearance, the
vehicle could be damaged while being towed from the rear.