2012 Lexus CT200h EV Mode

244
2-3. Operating the lights and windshield wipers
CT200h_OM_OM76067E_(EE)
The windshield wipers and washer can be operated when
The “POWER” switch is in ON mode.
Increases the sensitivity
Decreases the sensitivity
Washer/wiper dual opera-
tion
The wipers will automati-
cally operate a couple of
times after the washer
squirts.

245
2-3. Operating the lights and windshield wipers
2
When driving
CT200h_OM_OM76067E_(EE)
Raindrop sensor (vehicles with rain-sensing windshield wipers)
If the wiper switch is turned to the “AUTO” position while the
“POWER” switch is in ON mode, the wipers will operate once to show
that AUTO mode is activated.
If the temperature of the raindrop sensor is 90 C (194 F) or higher, or -
15 C (5 F) or lower, automatic operation may not occur. In this case,
operate the wipers in any mode other than “AUTO”.
If no windshield washer fluid sprays
Check that the washer nozzles are not blocked if there is washer fluid in the
washer fluid tank.
CAUTION
Caution regarding the use of windshield wipers in “AUTO” mode (vehicles
with rain-sensing windshield wipers)
The windshield wipers may operate unexpectedly if the sensor is touched or
the windshield is subject to vibration in “AUTO” mode. Take care that your
fingers etc. do not become caught in the windshield wipers.
The raindrop sensor judges the amount
of raindrops.
An optical sensor is adopted. It may not
operate properly when sunlight from
the rising or setting of the sun intermit-
tently strikes the windshield, or if bugs
etc. are present on the windshield.

247
2-3. Operating the lights and windshield wipers
2
When driving
CT200h_OM_OM76067E_(EE)
Rear window wiper and washer
: If equipped
The rear window wiper and washer can be operated when
The “POWER” switch is in ON mode.
The wiper operation is selected by moving the lever as follows:
Intermittent window wiper
operation
Normal window wiper
operation
Washer/wiper dual opera-
tion
Washer/wiper dual opera-
tion

249
2-3. Operating the lights and windshield wipers
2
When driving
CT200h_OM_OM76067E_(EE)
Headlight cleaner switch
: If equipped
The headlight cleaners can be operated when
The “POWER” switch is in ON mode and the headlight switch is turned on.
Windshield washer linked operation
Only for the first time when the windshield washer is operated with the
“POWER” switch in ON mode and the headlights on, the headlight cleaners
will operate once.
(P. 241)
NOTICE
When the washer fluid tank is empty
Do not press the switch continually as the washer fluid pump may overheat.
Washer fluid can be sprayed on the headlights.
Press the switch to clean the
headlights.

255
2-4. Using other driving systems
2
When driving
CT200h_OM_OM76067E_(EE)
Dynamic radar cruise control
: If equipped
Dynamic radar cruise control supplements conventional cruise control
with a vehicle-to-vehicle distance control. In vehicle-to-vehicle dis-
tance control mode, the vehicle automatically accelerates or deceler-
ates in order to maintain a set following distance from vehicles ahead.
Indicators
Display
Set speed
Vehicle-to-vehicle distance
button
Cruise control switch

256
2-4. Using other driving systems
CT200h_OM_OM76067E_(EE)
Setting the vehicle speed (vehicle-to-vehicle distance control
mode)
Press the “ON-OFF” button
to activate the cruise control.
Radar cruise control indicator
will come on.
Press the button again to
deactivate the cruise control.
Accelerate or decelerate the
vehicle to the desired speed,
and push the lever down to
set the speed.
“SET” will be displayed.
The vehicle speed at the
moment the lever is released
becomes the set speed.
STEP1
STEP2

257
2-4. Using other driving systems
2
When driving
CT200h_OM_OM76067E_(EE)
Adjusting the set speed
To change the set speed, operate the lever until the desired set
speed is displayed.
Increases the speed
Decreases the speed
Fine adjustment: Momentar-
ily move the lever in the
desired direction.
Large adjustment: Hold the
lever in the desired direction.
In the vehicle-to-vehicle distance control mode, the set speed will
be increased or decreased as follows:
When the set speed is shown in “km/h”
Fine adjustment: By approximately 5 km/h (3.1 mph) each
time the lever is operated
Large adjustment: By approximately 5 km/h (3.1 mph) for each
0.75 seconds the lever is held
When the set speed is shown in “MPH”
Fine adjustment: By approximately 5 mph (8 km/h) each time
the lever is operated
Large adjustment: By approximately 5 mph (8 km/h) for each
0.75 seconds the lever is held
In the constant speed control mode (P. 263), the set speed will
be increased or decreased as follows:
Fine adjustment: By approximately 1.6 km/h (1 mph) each time
the lever is operated
Large adjustment: The set speed can be increased or decreased
continually until the lever is released.

258
2-4. Using other driving systems
CT200h_OM_OM76067E_(EE)
Changing the vehicle-to-vehicle distance
Pressing the button changes
the vehicle-to-vehicle dis-
tance as follows:
Long
Medium
Short
The vehicle-to-vehicle dis-
tance is set automatically to
long mode when the
“POWER” switch is turned
to ON mode.
If a vehicle is running ahead
of you, the preceding vehicle
mark will also be displayed.
Vehicle-to-vehicle distance settings
Select a distance from the table below. Note that the distances
shown correspond to a vehicle speed of 80 km/h (50 mph).
Vehicle-to-vehicle distance increases/decreases in accordance
with vehicle speed.
Preceding vehicle
Distance optionsVehicle-to-vehicle distance
LongApproximately 50 m (160 ft.)
MediumApproximately 40 m (130 ft.)
ShortApproximately30m(100ft.)