2012 Lancia Ypsilon seat adjustment

SEATS
WARNING
All adjustments must be made with
the car stationary.
FRONT SEATS
Lengthwise adjustment
Lift the lever A fig. 17 and push the seat forwards
or backwards: in driving position your arms
should rest on the rim of the steering wheel.
WARNING
Once you have released the
adjustment lever, always check that
the seat is locked on the guides by trying to
move it back and forth. If the seat is not
locked into place, it may unexpectedly slide
and cause the driver to lose control of the
car.
Height adjustment
(for versions/markets, where provided)
Move lever B fig. 18 upwards or downwards to
achieve the required height.
IMPORTANT Carry out the adjustment while
sitting on the seat involved (driver side or
passenger side).
fig. 18
L0F0063
34GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
fig. 17
L0F0062

Backrest angle adjustment
Adjust knob C fig. 19 to obtain the required
position.
Lumbar adjustment
(for versions/markets, where provided)
The position of the back against the seat backrest
can be adjusted by turning knob D fig. 20.
Electric seat heating
(for versions/markets, where provided)
With the ignition key turned to MAR, press
buttons E fig. 21 to switch the function on/off.
When the function is activated, the LED on the
buttons will light up.IMPORTANT If this function is activated with
engine off the battery will run down.
fig. 19
L0F0064
fig. 20
L0F0273
fig. 21
L0F0247
35GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

HEAD RESTRAINTSFRONT
They are height-adjustable: to adjust them,
operate as follows.
Upwards adjustment:raise the head restraint
until it clicks into place.
Downwards adjustment:press button A fig. 22
and lower the head restraint.
"Anti-Whiplash" Device
The head restraints are equipped with an
“Anti-Whiplash” device, which reduces the
distance between head and head restraint in the
event of a rear impact, thus mitigating the
"whiplash" effect.The head restraint may move when the backrest is
pressed by the occupant's torso or hand: this
behaviour is caused by the system and should not
be considered a malfunction.
WARNING
All adjustments must be made with
the car stationary. Head restraints
must be adjusted so that the head, rather
than the neck, rests on them. Only when they
are adjusted in this manner can they serve
their intended purpose.
WARNING
To make the best use of the head
restraint's protective action, adjust
the backrest so that you are sitting upright
and keep your head as close as possible
to the head restraint.
REAR
(for versions/markets, where provided)
Two height-adjustable head restraints are
provided for the rear seats. On some versions a
head restraint is also provided for the central seat.
Upwards adjustment:raise the head restraint
until it clicks into place.
fig. 22
L0F0061
36GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Downwards adjustment:press button A fig. 23
and lower the head restraint.
Proceed as follows to remove the head restraints:
❒raise the head restraints to their maximum
height;
❒press buttons A and B fig. 23 at the side of the
two supports, then remove the head restraints
by pulling them upwards.
IMPORTANT If the rear seats are used, always set
the head restraints in the "completely raised"
position.
STEERING WHEELThe steering wheel can be adjusted vertically.
To adjust, move lever A fig. 24 downwards to
position 1, then adjust the steering wheel to the
most suitable position and lock it in position
by moving lever A to position 2.
WARNING
All adjustments must be carried out
only with the car stationary and
engine off.
A
B
fig. 23
L0F0201
fig. 24
L0F0078
37GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

HEADLIGHTSLIGHT BEAM DIRECTION
The correct alignment of the headlights is
important for the comfort and safety of not only
the driver but all other road users. This is also
covered by a specific rule of the highway code.
The headlights must be correctly aimed to
guarantee the best visibility conditions for all
drivers while travelling with headlights on.
Contact a Lancia Dealership to have the
headlights properly adjusted.
Check beam alignment every time the load or its
distribution changes.
IMPORTANT When the gas discharge (Xenon)
headlamps (for versions/markets, where provided)
are switched on, normally parabolas and light
beam move vertically for about 2 seconds until
headlamp alignment has stabilised.
HEADLAMP ALIGNMENT CORRECTOR
This device works with the ignition key in the
MAR position and the dipped headlights on.
Headlight alignment adjustment
Press the
or
buttons to adjust fig. 69. The
instrument panel display shows the position in
relation to the adjustment set.
Position 0 - one or two persons on the front seats
Position1-4personsPosition2-4persons + load in the luggage
compartment
Position 3 - driver + maximum admissible load all
stored in the luggage compartment.
IMPORTANT Check alignment every time the
load carried changes.
IMPORTANT If the car is equipped with (Xenon)
gas discharge headlights, the headlight alignment
is controlled electronically, as a consequence the
and
buttons are not present.
FOG LIGHT ALIGNMENT
(for versions/markets, where provided)
Contact a Lancia Dealership to have the
headlights properly adjusted.
fig. 69
L0F0224
87GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX