2012 Lancia Ypsilon maintenance

tyre pressure on gauge B fig. 125 with
compressor off to obtain a more precise reading;
❒if after five minutes it is still impossible to reach
at least 1.8 bar, disengage the compressor from
the valve and power socket, then move the
car forwards by approx. ten metres in order to
distribute the sealing fluid inside the tyre evenly,then repeat the inflation operation;
❒if after this operation you still cannot reach at
least 1.8 bar after 5 minutes from switching
on the compressor, do not resume driving but
contact a Lancia Dealership;
WARNING
Apply the adhesive label where it can
be easily seen by the driver as a
reminder that the tyre has been treated with
the tyre quick repair kit. Drive carefully,
particularly on bends. Do not exceed 80
km/h. Do not accelerate or brake suddenly.
❒after driving for about 10 minutes stop and
check the tyre pressure again;pull up the
handbrake;For the safety of the car when it is
parked, follow the indication in the paragraph
"When parked" in the chapter "Starting up and
driving" .
WARNING
If the pressure has fallen below 1.8
bar, do not drive any further: the
automatic tyre quick repair kit cannot
guarantee the correct hold because the tyre
is too damaged. Contact a Lancia
Dealership.
fig. 125
L0F0181
fig. 126
L0F0178
178
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

❒if a pressure value of at least 1.8 bar is detected,
restore the correct pressure (with the engine
running and the handbrake engaged), resume
driving and drive with care to nearest Lancia
Dealership.
WARNING
Inform the dealership that the tyre
has been repaired using the tyre
quick repair kit. Give the instruction booklet
to the personnel charged with handling the
treated tyre.
CHECKING AND RESTORING TYRE
PRESSURE
The compressor can also be used to check and, if
necessary, adjust the tyre pressure. Release quick
connector A fig. 127 and connect it directly to
the valve of the tyre to be inflated.
REPLACING THE BOTTLE
Proceed as follows:
❒disconnect connection A fig. 128;
❒turn the cylinder to be replaced anticlockwise
and raise it;❒fit the new cylinder and turn it clockwise;
❒connect connection A to the cylinder and insert
the transparent pipe B into its housing.
fig. 127
L0F0180
fig. 128
L0F0008
179GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

REPLACING EXTERIOR BULBSFor the type of bulb and power rating, see
“Changing a bulb".
FRONT LIGHT UNITS
These contain the bulbs for the side lights/day
lights (DRL), dipped beams, main beams and
direction indicators. The bulbs are arranged
as follows fig. 129:ASide lights/daytime running lights and main
beam headlightsBDipped beam headlightsCDirection indicatorsSIDE LIGHTS/DAY LIGHTS (DRL)
To change the bulb, proceed as follows:
❒remove cover A fig. 129;
❒remove snap-fitted bulb holder B fig. 130,
remove the bulb C and replace it;
❒refit the new bulb then reinsert the bulb holder
B in its housing;
❒then refit the cover A fig. 129.fig. 129
L0F0033
fig. 130
L0F0069
180
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

MAIN BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove cover A fig. 129;
❒turn the connector unit and the bulb holder B
fig. 131 anticlockwise;
❒remove the bulb C from connector D and
replace it;
❒refit the new bulb on the connector making sure
that it is locked correctly, then reinsert the
connector unit and the bulb holder B in
its housing;
❒then refit the cover A fig. 129.DIPPED BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove cover B fig. 129;
❒turn the snap-fitted bulb holder unit C fig. 132
anticlockwise, remove bulb D and replace it;
❒refit the new bulb then reinsert the bulb holder
unit C in its housing;
❒then refit the cover B fig. 129.
DIRECTION INDICATORS
Front
To change the bulb, proceed as follows:
❒rotate the cover C fig. 129 anticlockwise;
❒remove the bulb D fig. 133 from its housing E.
Side
To change the bulb, proceed as follows:
fig. 131
L0F0068
fig. 132
L0F0070
181GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

❒adjust the lens A fig. 134 to compress in the
internal catch B, then pull the unit outwards;
❒turn the bulb holder C anticlockwise, extract the
bulb and replace it;❒refit the bulb holder C in the lens and turn it
clockwise;
❒refit the unit making sure that the internal catch
B clips into position.
FOG LIGHTS
(for versions/markets, where provided)
Replace the bulb as follows:
❒steer the wheel completely;
❒adjust the tabs A fig. 135 and remove the flap
B;
❒adjust the catch C fig. 136 and disconnect the
electrical connector D;
❒remove the cover E by turning it clockwise (see
the word OFF and the arrow on the cover);
❒release the catches F fig. 137 removing them
outwards;
fig. 133
L0F0071
fig. 134
L0F0209
fig. 135
L0F0205
182
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

❒release the connector G fig. 138 and replace the
bulb H;
❒refit the new lamp and carry out the procedure
described previously in reverse.REAR LIGHT CLUSTERS
These contain the bulbs for the side lights, brake
lights and direction indicators. The reversing
lights and rear fog lights are located instead in the
rear bumper.
fig. 136
L0F0206
fig. 137
L0F0207
fig. 138
L0F0208
183GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

The bulbs are arranged as follows fig. 139:ADirection indicators
BBrake lights
DIRECTION INDICATORS/BRAKE LIGHTS
Turn the bulb holder in directionO(open) to
replace the bulbs. After replacing the bulb, turn
the bulb holder in directionC(close).
SIDE LIGHTS
These are LED lights. Contact a Lancia
Dealership for replacement.
3rd
BRAKE LIGHTS
These are located in the tailgate and are LED
lights. Contact a Lancia Dealership for
replacement.
REAR FOG LIGHT
To change the bulb, proceed as follows:
❒working from inside the bumper, turn the bulb
holder unit A fig. 140 by a 1/4 turn;
❒extract the bulb and replace it;
❒refit the new bulb then reinsert the bulb holder
in its housing.
WARNING
Before replacing bulb, wait for the
catalytic converter to cool down:
RISK OF BURNS!
fig. 139
L0F0034
184
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

REVERSE LIGHT
To change the bulb, proceed as follows:
❒working from inside the bumper, turn the bulb
holder unit B fig. 140 by a 1/4 turn;
❒extract the bulb and replace it;
❒refit the new bulb then reinsert the bulb holder
in its housing.
NUMBER PLATE LIGHTS
To replace the bulbs proceed as follows:
❒remove lens A fig. 141;
❒turn the bulb holder B fig. 142 anticlockwise,
extract the bulb C and replace it;
❒refit the lens.
fig. 140
L0F0219
fig. 141
L0F0259
fig. 142
L0F0214
185GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX