2012 Lancia Musa stop start

127
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
If when turning the key to
MAR the warning light ¬does not turn on or if it stays on
when travelling (together with the
message on the multifunctional
display, where provided) there
could be a failure in safety sys-
tems; in this event air bags or pre-
tensioners may not be deployed in
case of impact or, in a minor num-
ber of cases, they be deployed ac-
cidentally. Contact Lancia Dealer-
ship immediately to have the sys-
tem checked.
Failure of warning light
¬is indicated by warning
light“which will blink for longer
than the normal 4 seconds indicat-
ing that the front passenger airbag
is off. The airbag system will au-
tomatically deactivate the passen-
ger airbag (front and side, for ver-
sions/markets, where provided). In
this case, warning light
¬may not
indicate fault to the system. Con-
tact Lancia Dealership immedi-
ately to have the system checked.
WARNING
WARNING
HOT ENGINE COOLANT
(red)
When the ignition key is
moved to MAR, the warning
light turns on and should go off after
a few seconds.
The warning light turns on when the
engine is overheated.
If the warning light comes on, proceed
as follows:
❒during normal travel: stop the
car, stop the engine and check that
the water level in the vessel is not
under the MINline. In this case,
wait for a few minutes for the en-
gine to cool down when slowly and
carefully open the cap, top-up with
coolant and check that the level is
between the MINandMAXrefer-
ences on the vessel itself. Also check
for leakages. Go to a Lancia Deal-
ership if the warning should come
on when the engine is started again.
u
❒In the case of demanding use
(e.g. towing trailers uphill or car at
full load): slow down and stop the
car if the warning light stays on.
Stand for 2 or 3 minutes with the
engine running and slightly acceler-
ated to promote a better circulation
of coolant. Then stop the engine.
Check correct liquid level as de-
scribed above.
IMPORTANT After taxing operation,
it is advisable to keep the engine on
and slightly accelerated for a few min-
utes before switching it off.
The display will show the dedicated
message.
LOW BATTERY
CHARGE (red)
When the ignition key is
moved to MAR, the warning
light turns on and should go out as
soon as the engine is started (with the
engine running at idle speed a brief
delay in going out is allowed). Go to
a Lancia Dealership immediately if
the warning light stays on.
w

128
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
LIGHT STAYS ON:
LOW ENGINE OIL
PRESSURE (red)
FLASHING LIGHT:
EXHAUSTED ENGINE OIL
(only Multijet versions
with DPF - red)
When the ignition key is turned to
MAR (ON), the warning light switches
on and should go out as soon as the
engine is started.
1. Low engine oil pressure
The warning light turns on and stays
on constantly (for versions/markets,
where provided) along with the mes-
sage on the display when the system
detects that engine oil pressure is low.
v
2. Exhausted engine oil
(only Multijet versions
with DPF)
The warning light will flash and
a specific message will appear on the
display (for versions/markets, where
provided). The warning light may
flash in the following ways, depend-
ing on the version:
– for 1 minute every two hours;
– for 3 minute cycles with the warn-
ing light off for intervals of 5 seconds
until oil is changed.
After the initial warning, each time
the engine is started up, the warning
light will continue to flash in the
above mentioned modes, until the oil
is changed. A specific message will
appear on the display (for versions/
markets, where provided) in addition
to the warning light.
If the warning light flashes, this does
not mean that the car is defective but
simply informs the driver that it is
now necessary to change the oil as
a result of regular vehicle use.
If the warning light v
turns on when the vehicle
is travelling (on certain versions
together with the message on the
display) stop the engine immedi-
ately and contact a Lancia Deal-
ership.
WARNING
Note that engine oil is exhausted faster
under the following circumstances:
– use of the vehicle prevalently for city
driving, requiring more frequent re-
generation of DPF
– use of the vehicle for short drives, in
which the engine does not have time
to reach its regular operating temper-
ature
– repeated interruption of the regen-
eration process, signalled by the DPF
warning light coming on.
WARNING
Exhausted engine oil should
be replaced as soon as pos-
sible after the warning light comes
on, never more than 500 km after
the warning light first comes on.
Failure to change the oil within the
first 500 km may result in severe
damage to the engine and will re-
sult in forfeiture of the warranty.
Remember that when the warning
light flashes, it does not mean that
the level of engine oil is low, so if
the light flashes you must not top
up.

130
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
Go to a Lancia Dealership
as soon as possible if warn-
ing light
Ueither does not
light up when the key is
turned to MAR to if while travelling
the warning lights comes on either
steady or blinking (along with a
message on the multifunctional dis-
play, where provided). The opera-
tion of warning light
Umay be
checked by the traffic police using
specific devices. Follow the laws in
force in the country where you are
driving.
FRONT PASSENGER
AIRBAG
DEACTIVATED
(amber)
Warning light “comes on when front
passenger’s airbag is deactivated.
With the front passenger’s airbag on,
when the ignition key is moved to
MAR, the warning light “comes on
steadily for about 4 seconds; then, it
continues to flash for 4 seconds and
finally goes off.
“
Failure of the warning
light“is indicated by
warning light
¬. The airbag sys-
tem will automatically deactivate
the passenger airbag (front and
side, “). Contact Lancia Dealership
immediately to have the system
checked.
WARNING
EOBD engine control system
failure
In normal conditions, when the igni-
tion key is moved to MAR, the warn-
ing light turns on and should go off
after engine start-up. This indicates
that the warning light is working cor-
rectly. If the warning light either stays
on or comes on while travelling:
❒steady light: a fault in the supply/
ignition system which could cause
high emissions at the exhaust, pos-
sible lack of performance, poor
handling and high consumption
levels.
The display will show the dedicated
message.
In these conditions, you may continue
travelling at moderate speed without
demanding excessive effort from the
engine. Prolonged use of the car with
the warning light on may cause dam-
age. Go to a Lancia Dealership as
soon as possible. If warning light will
go out after the fault goes away but it
will be stored in the system.
❒blinking light: indicates the possi-
bility of damage to the catalyser
(see “EOBD system” in section
“Dashboard and controls”). If the light flashes, release the accel-
erator pedal to lower the speed of the
engine until the warning light stops
flashing; continue the journey at mod-
erate speed, trying to avoid driving
conditions that may cause further
flashing and contact Lancia Dealer-
ship as soon as possible.

131
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
ABS SYSTEM FAILURE
(amber)
When the ignition key is
moved to MAR, the warning
light turns on and should go off after
a few seconds.
The warning light will light up when
the system is either not working or not
available. In the case, the braking sys-
tem will work as normal without the
extra potentials offered by the ABS
system. Drive carefully and go to a
Lancia Dealership as soon as possible.
The display will show the dedicated
message.
>
FUEL RESERVE
(amber)
When the ignition key is
moved to MAR, the warning
light turns on and should go off after
a few seconds.
The warning light turns on when
about 6/7 litres fuel are left in the
tank.
IMPORTANT The warning light will
blink to indicate a system failure. Go
to a Lancia Dealership to have the
system checked.
K
GLOW PLUG
WARMING
(Multijet versions -
amber)
GLOW PLUG FAILURE
(Multijet versions -amber)
Glow plugs
The warning light will go on when the
key is turned to MAR. It will go out
as soon as the glow plugs have
reached a predetermined tempera-
ture. Start the engine as soon as the
warning light goes out.
IMPORTANT With hot ambient tem-
perature, warning light stays on for
very short time.
Glow plug warming failure
The warning light will blink in the
event of a failure to the glow plug
heating system. Go to a Lancia Deal-
ership as soon as possible.
The display will show the dedicated
message.
m
WATER IN DIESEL
FUEL FILTER (Multijet
versions - amber)
When the ignition key is
moved to MAR, the warning light
turns on and should go off after a few
seconds.
The warning light cturns on when
there is water in the diesel fuel filter.
The display will show the dedicated
message.
c
The presence of water in the
feeding circuit may cause
severe damage to the injec-
tion system and irregular
engine operation. If warning light c
lights up (on some versions with the
message on the display), go to a
Lancia Dealership as soon as pos-
sible to have the system bled. Water
may have been introduced in the
tank if this appears immediately af-
ter refuelling: in this case, stop the
engine immediately and contact a
Lancia Dealership.

141
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
For a more accurate reading,
check pressure gauge F-fig. 6with
the compressor off;
❒if after 5 minutes it is still impossi-
ble to reach at least 1.5 bar, disen-
gage compressor from valve and
current outlet, then move the car
forth for approx. ten metres in or-
der to distribute the sealing fluid
inside the tyre evenly, then repeat
the inflation operation;
❒If after this operation it is still im-
possible after 5 minutes to reach at
least 1.8 bar, do not start driving
since the tyre is excessively dam-
aged and the quick tyre repair kit
cannot guarantee suitable sealing,
contact Lancia Dealership.
fig. 8L0D0485m
Apply the adhesive label in
a position clearly visible
by the driver as a reminder that
the tyre has been treated with the
quick repair kit. Drive carefully,
particularly on bends. Do not ex-
ceed 80 km/h. Do not accelerate or
brake suddenly.
WARNING
Stop if the pressure has
dropped to less than 1.8
bars: the automatic Fix & Go quick
repair kit cannot work properly
because the tyre is excessively
damaged. Go to a Lancia Dealer-
ship.
WARNING
❒if reaching the tyre pressure speci-
fied in paragraph “Inflation pres-
sure” in section “Technical Specifi-
cations”, start driving immediately;
❒after driving for about 10 minutes
stop and check again the tyre pres-
sure; pull up the handbrake;
❒if at least 1.8 bar pressure is read,
restore proper pressure (with en-
gine running and handbrake on)
and restart;
❒drive with the utmost care to the
nearest Lancia Dealership.
FOR CHECKING AND
RESTORING PRESSURE ONLY
The compressor may also be used for
restoring pressure only. Release the
quick coupling and connect directly
to the tyre valve; in this way, the
cylinder will not be connected to the
compressor and no sealant will be in-
jected.

144
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
To change a wheel proceed as follows:
❒stop the car in a position so that it
is not a danger for on-coming traf-
fic and where you can replace the
wheel safely. The ground must be
flat and compact;
❒turn the engine off and pull up the
handbrake.
❒engage first gear or reverse;
❒lift the boot mat;
❒loosen the fastening device A-fig.
10;
❒take out the tool container Band
take it near to the wheel to be
changed;
❒take the space saver spare wheel
C;
L0D0161mfig. 10
Important notes:
❒the jack cannot be repaired: replace
with an original spare part if dam-
aged;
❒no tool other than its cranking de-
vice may be fitted on the jack.

159
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
FUSE TABLE
Dashboard fusebox fig. 37
USERSFUSE AMPERES
Right dipped headlampF12 7.5
Left dipped headlamp/headlamp alignment corrector F13 7.5
Engine compartment fuse box relay coils, body computer F31 7.5
Rear left electric windowF33 20
Rear right electric windowF34 20
+15 Signal from switch on brake pedal for control units, reverse light/s, flow meter (MultiJet versions,
Start&Stop excluded), heater plug control unit (1.3 MultiJet EURO 5 versions), clutch control (Start&Stop),
brake servo (Start&Stop) and water sensor in diesel (*) F35 7.5
Boot unlocking F36 10
+15 Brake lights, instrument panel (*)F37 7.5
Door lock, fuel flap actuatorF38 20
+30 Radio, navigator, Blue&Me™ system, electric window control unit, tyre pressure control unit,
climate control, EOBD diagnosis socket (*)F39 10
Heated rear window F40 30
Heated electric mirrorsF41 7.5
Windscreen wiper, windscreen/rear window washer F43 30
Cigar lighter / current socket on tunnelF44 15
Heated front seatsF45 15
Luggage compartment current socketF46 15
Driver's side front electric windowF47 20
Passenger 's side front electric windowF48 20
+15 Controls on the steering wheel, lighting for sun roof controls, left and centre dashboards, rain/dusk sensor,
electric mirrors, heated front seat controls (*)F49 7.5
+15 Navigator, radio setup, Blue&Me™ system, parking sensors, tyre pressure control unit, power window
control unit, electric mirrors, climate control system knob lighting and ECO button, Cruise Control, voltage
stabiliser (Start&Stop) (*)F51 7.5
Rear window wiperF52 15
+30 Instrument panel, rear fog lamp/s (*)F53 7.5
(*) +30 = battery direct positive pole (not ignition switch)
+15 = positive pole ignition switch

160
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
Fusebox in engine compartment fig. 39
USERSFUSE AMPERES
HornF10 15
Right beamF14 7.5
Left beamF15 7.5
CompressorF19 7.5
Starting system (Start&Stop)F20 30
Fuel pumpF21 15
Fog lightsF30 15
(*) +30 = battery direct positive pole (not ignition switch)
+15 = positive pole ignition switch
Optional fusebox (on auxiliary bracket) fig. 37
USERSFUSE AMPERES
+30 External radio amplifier (*)F54 15
+30 Sunroof (*)F58 20
(*) +30 = battery direct positive pole (not ignition switch)
+15 = positive pole ignition switch