2012 Lancia Flavia tire pressure

 SHALLOW STANDING WATER . . . . . . . . . . . 143
 POWER STEERING . . . . . . . . . . . . . . . . . . . . . . 144  POWER STEERING FLUID CHECK . . . . . . . . 144
 PARKING BRAKE . . . . . . . . . . . . . . . . . . . . . . . 145
 ANTI-LOCK BRAKE SYSTEM (ABS) . . . . . . . . . 146
 ELECTRONIC BRAKE CONTROL SYSTEM . . . . 147  ANTI-LOCK BRAKE SYSTEM (ABS) . . . . . . . 147
 TRACTION CONTROL SYSTEM (TCS) . . . . . . 148
 BRAKE ASSIST SYSTEM (BAS) . . . . . . . . . . . 148
 ELECTRONIC STABILITY CONTROL (ESC) . . 149
 ESC ACTIVATION/MALFUNCTIONINDICATOR LIGHT AND ESC OFF
INDICATOR LIGHT . . . . . . . . . . . . . . . . . . . . 150
 TIRES — GENERAL INFORMATION . . . . . . . . . 151  TIRE PRESSURE . . . . . . . . . . . . . . . . . . . . . . 151
 TIRE INFLATION PRESSURES . . . . . . . . . . . 151
 RADIAL-PLY TIRES . . . . . . . . . . . . . . . . . . . 152
 TIRE SPINNING . . . . . . . . . . . . . . . . . . . . . . 153
 TREAD WEAR INDICATORS . . . . . . . . . . . . . 153
 LIFE OF TIRE . . . . . . . . . . . . . . . . . . . . . . . . 153
 REPLACEMENT TIRES . . . . . . . . . . . . . . . . . 154
 TIRE CHAINS . . . . . . . . . . . . . . . . . . . . . . . . . . 154
 TIRE ROTATION RECOMMENDATIONS . . . . . . 155
 TIRE PRESSURE MONITOR SYSTEM (TPMS) . . 155  PREMIUM SYSTEM . . . . . . . . . . . . . . . . . . . . 157
 FUEL REQUIREMENTS . . . . . . . . . . . . . . . . . . . 158
132

WARNING!(Continued)
 Always fully apply the parking
brake when leaving your vehicle
or it may roll and cause damage or
injury. Also, be certain to leave the
transmission in PARK. Failure to
do so may cause the vehicle to roll
and cause damage or injury.CAUTION!
If the “Brake Warning Light” re-
mains on with the parking brake
released, a brake system malfunc-
tion is indicated. Have the brake
system serviced by an authorized
dealer immediately.
ANTI-LOCK BRAKE
SYSTEM (ABS)
The Anti-Lock Brake System (ABS)
provides increased vehicle stability
and brake performance under most
braking conditions. The system oper-
ates with a separate computer to
modulate the hydraulic pressure to
prevent wheel lock-up and avoid
skidding on slippery surfaces.
WARNING!
 Pumping of the anti-lock brakes will diminish their effectiveness
and may lead to a collision.
Pumping makes the stopping dis-
tance longer. Just press firmly on
your brake pedal when you need
to slow down or stop.
 The ABS cannot prevent the natu-
ral laws of physics from acting on
the vehicle, nor can it increase
braking or steering efficiency be-
yond that afforded by the condi-
tion of the vehicle brakes and tires
or the traction afforded.
 The ABS cannot prevent colli-
sions, including those resulting
from excessive speed in turns, fol-
lowing another vehicle too closely,
or hydroplaning.
 The capabilities of an ABS-
equipped vehicle must never be
exploited in a reckless or danger-
ous manner, which could jeopar-
dize the user's safety or the safety
of others. The
“Anti-Lock Brake
Warning Light” monitors
the Anti-Lock Brake Sys-
tem. The light will come on
when the ignition switch is turned to
the ON position and may stay on for
as long as four seconds.
If the “Anti-Lock Brake Warning
Light” remains on or comes on while
driving, it indicates that the anti-lock
portion of the brake system is not
functioning and that service is re-
quired. However, the conventional
brake system will continue to operate
normally if the “Brake Warning
Light” is not on.
If the “Anti-Lock Brake Warning
Light” is on, the brake system should
be serviced as soon as possible to re-
store the benefits of anti-lock brakes.
If the “Anti-Lock Brake Warning
Light” does not come on when the
ignition switch is turned to the ON
position, have the bulb repaired as
soon as possible.
If both the “Brake Warning Light”
and the “Anti-Lock Brake Warning
Light” remain on, the Anti-Lock
146

Brake (ABS) and Electronic Brake
Force Distribution (EBD) Systems are
not functioning. Immediate repair to
the ABS system is required. See your
authorized dealer.
When the vehicle is driven over
11 km/h, you may hear a slight click-
ing sound as well as some related mo-
tor noises. These noises are the system
performing its self-check cycle to en-
sure that the ABS system is working
properly. This self check occurs each
time the vehicle is started and accel-
erated past 11 km/h.
ABS is activated during braking un-
der certain road or stopping condi-
tions. ABS-inducing conditions can
include ice, snow, gravel, bumps, rail-
road tracks, loose debris, or panic
stops.
You also may experience the following
when the brake system goes into anti-
lock:
 The ABS motor running (it maycontinue to run for a short time
after the stop),
 the clicking sound of solenoid valves,  brake pedal pulsations,
 and a slight drop or fall away of the
brake pedal at the end of the stop.
These are all normal characteristics of
ABS.
WARNING!
The Anti-Lock Brake System con-
tains sophisticated electronic equip-
ment that may be susceptible to in-
terference caused by improperly
installed or high output radio trans-
mitting equipment. This interfer-
ence can cause possible loss of anti-
lock braking capability. Installation
of such equipment should be per-
formed by qualified professionals.
All vehicle wheels and tires must be
the same size and type, and tires must
be properly inflated to produce accu-
rate signals for the computer. ELECTRONIC BRAKE
CONTROL SYSTEM
Your vehicle may be equipped with an
optional advanced electronic brake
control system that includes Anti-
Lock Brake System (ABS), Traction
Control System (TCS), Brake Assist
System (BAS), and Electronic Stabil-
ity Control (ESC). All systems work
together to enhance vehicle stability
and control in various driving condi-
tions and are commonly referred to as
ESC.
ANTI-LOCK BRAKE
SYSTEM (ABS)
This system aids the driver in main-
taining vehicle control under adverse
braking conditions. The system con-
trols hydraulic brake pressure to pre-
vent wheel lock-up and help avoid
skidding on slippery surfaces during
braking. Refer to “Anti-Lock Brake
System” in “Starting and Operating”
for further information.
147

TRACTION CONTROL
SYSTEM (TCS)
This system monitors the amount of
wheel spin of each of the driven
wheels. If wheel spin is detected,
brake pressure is applied to the slip-
ping wheel(s) and engine power is
reduced to provide enhanced accel-
eration and stability. A feature of the
TCS system functions similar to a lim-
ited slip differential and controls the
wheel spin across a driven axle. If one
wheel on a driven axle is spinning
faster than the other, the system will
apply the brake of the spinning wheel.
This will allow more engine torque to
be applied to the wheel that is not
spinning. This feature remains active
even if TCS and ESC are in the “Par-
tial Off” mode. Refer to “Electronic
Stability Control (ESC)” in this sec-
tion of this manual.BRAKE ASSIST SYSTEM
(BAS)
The BAS is designed to optimize the
vehicle’s braking capability during
emergency braking maneuvers. The
system detects an emergency braking
situation by sensing the rate and
amount of brake application and then
applies optimum pressure to the
brakes. This can help reduce braking
distances. The BAS complements the
Anti-Lock Brake System (ABS). Ap-
plying the brakes very quickly results
in the best BAS assistance. To receive
the benefit of the system, you must
apply continuous braking pressure
during the stopping sequence. Do not
reduce brake pedal pressure unless
braking is no longer desired. Once the
brake pedal is released, the BAS is
deactivated.
WARNING!
 The BAS cannot prevent the natu-
ral laws of physics from acting on
the vehicle, nor can it increase
braking efficiency beyond that af-
forded by the condition of the ve-
hicle brakes and tires or the trac-
tion afforded.
 The BAS cannot prevent colli-
sions, including those resulting
from excessive speed in turns, fol-
lowing another vehicle too closely,
or hydroplaning.
 The capabilities of a BAS-
equipped vehicle must never be
exploited in a reckless or danger-
ous manner, which could jeopar-
dize the user’s safety or the safety
of others.
148

 The ESC system will make buzz-ing or clicking sounds when it is
active. This is normal; the
sounds will stop when ESC be-
comes inactive following the
maneuver that caused the ESC
activation.
The “ESC OFF Indicator
Light” indicates the Elec-
tronic Stability Control
(ESC) is off.
TIRES — GENERAL
INFORMATION
TIRE PRESSURE
Proper tire inflation pressure is essen-
tial to the safe and satisfactory opera-
tion of your vehicle. Three primary
areas are affected by improper tire
pressure: Safety
WARNING!
 Improperly inflated tires are dan-
gerous and can cause collisions.
 Under-inflation increases tire
flexing and can result in over-
heating and tire failure.
 Over-inflation reduces a tir e's
ability to cushion shock. Objects
on the road and chuckholes can
cause damage that result in tire
failure.
 Over -inflated or under-inflated
tires can affect vehicle handling
and can fail suddenly, resulting in
loss of vehicle control.
 Unequal tire pressures can cause
steering problems. You could lose
control of your vehicle.
 Unequal tire pressures from one
side of the vehicle to the other can
cause the vehicle to drift to the
right or left.
 Always drive with each tire in-
flated to the recommended cold
tire inflation pressure. Economy
Improper inflation pressures can
cause uneven wear patterns to de-
velop across the tire tread. These ab-
normal wear patterns will reduce
tread life resulting in a need for earlier
tire replacement. Under-inflation,
also increases tire rolling resistance
resulting in higher fuel consumption.
Ride Comfort And Vehicle
Stability
Proper tire inflation contributes to a
comfortable ride. Over-inflation pro-
duces a jarring and uncomfortable
ride.
TIRE INFLATION
PRESSURES
The proper cold tire inflation pressure
is listed on the
driver's sideB-Pillar or
rear edge of the driver's side door.
Some vehicles may have Supplemen-
tal Tire Pressure Information for ve-
hicle loads that are less than the maxi-
mum loaded vehicle condition. These
pressure conditions will be found in
the “Supplemental Tire Pressure In-
formation” section of this manual.
151

The pressure should be checked and
adjusted as well as inspecting for signs
of tire wear or visible damage at least
once a month. Use a good quality
pocket-type gauge to check tire pres-
sure. Do not make a visual judgement
when determining proper inflation.
Radial tires may look properly in-
flated even when they are under-
inflated.CAUTION!
After inspecting or adjusting the tire
pressure, always reinstall the valve
stem cap. This will prevent moisture
and dirt from entering the valve
stem, which could damage the valve
stem.
Inflation pressures specified on the
placard are always “cold tire inflation
pressure.” Cold tire inflation pressure
is defined as the tire pressure after the
vehicle has not been driven for at least
three hours, or driven less than
1.6 km after a three hour period. The
cold tire inflation pressure must not
exceed the maximum inflation pres-
sure molded into the tire sidewall. Check tire pressures more often if
subject to a wide range of outdoor
temperatures, as tire pressures vary
with temperature changes.
Tire pressures change by approxi-
mately 7 kPa per 7°C of air tempera-
ture change. Keep this in mind when
checking tire pressure inside a garage,
especially in the winter.
Example: If garage temperature =
20°C and the outside temperature =
0°C then the cold tire inflation pres-
sure should be increased by 21 kPa,
which equals 7 kPa for every 7°C for
this outside temperature condition.
Tire pressure may increase from 13 to
40 kPa during operation. DO NOT
reduce this normal pressure build up
or your tire pressure will be too low.
Tire Pressures For High Speed
Operation
The manufacturer advocates driving
at safe speeds within posted speed
limits. Where speed limits or condi-
tions are such that the vehicle can be
driven at high speeds, maintaining
correct tire inflation pressure is very
important. Increased tire pressureand reduced vehicle loading may be
required for high-speed vehicle op-
eration. Refer to original equipment
or an authorized tire dealer for recom-
mended safe operating speeds, load-
ing and cold tire inflation pressures.
WARNING!
High speed driving with your vehicle
under maximum load is dangerous.
The added strain on your tires could
cause them to fail. You could have a
serious collision. Do not drive a ve-
hicle loaded to the maximum capac-
ity at continuous speeds above
120 km/h.
RADIAL-PLY TIRESWARNING!
Combining radial ply tires with
other types of tires on your vehicle
will cause your vehicle to handle
poorly. The instability could cause a
collision. Always use radial ply tires
in sets of four. Never combine them
with other types of tires.
152

Cuts and punctures in radial tires are
repairable only in the tread area be-
cause of sidewall flexing. Consult
your authorized tire dealer for radial
tire repairs.
TIRE SPINNING
When stuck in mud, sand, snow, or icy
conditions, do not spin yourvehicle's
wheels faster than 48 km/h or for
longer than 30 seconds continuously
without stopping.
Refer to “Freeing A Stuck Vehicle” in
“What To Do In Emergencies” for fur -
ther information.WARNING!
Fast spinning tires can be danger-
ous. Forces generated by excessive
wheel speeds may cause tire damage
or failure. A tire could explode and
injure someone. Do not spin your
vehicle's wheels faster than 48 km/h
or for more than 30 seconds con-
tinuously when you are stuck, and
do not let anyone near a spinning
wheel, no matter what the speed. TREAD WEAR
INDICATORS
Tread wear indicators are in the origi-
nal equipment tires to help you in
determining when your tires should
be replaced.
These indicators are molded into the
bottom of the tread grooves. They will
appear as bands when the tread depth
becomes 2 mm. When the tread is
worn to the tread wear indicators, the
tire should be replaced.
LIFE OF TIRE
The service life of a tire is dependent
upon varying factors including but
not limited to:
 Driving style
 Tire pressure
 Distance driven
WARNING!
Tires and spare tire should be re-
placed after six years, regardless of
the remaining tread. Failure to fol-
low this warning can result in sud-
den tire failure. You could lose con-
trol and have a collision resulting in
serious injury or death.
Keep dismounted tires in a cool, dry
place with as little exposure to light as
possible. Protect tires from contact
with oil, grease, and gasoline.
1 — Worn Tire
2 — New Tire
153

REPLACEMENT TIRES
The tires on your new vehicle provide
a balance of many characteristics.
They should be inspected regularly
for wear and correct cold tire inflation
pressure. The manufacturer strongly
recommends that you use tires
equivalent to the originals in size,
quality and performance when re-
placement is needed (refer to the
paragraph on “Tread Wear Indica-
tors”). Refer to the “Tire and Loading
Information” placard for the size des-
ignation of your tire. The Load Index
and Speed Symbol for your tire will be
found on registration Document/log
book.
It is recommended to replace the two
front tires or two rear tires as a pair.
Replacing just one tire can seriously
affect your vehicle’s handling. If you
ever replace a wheel, make sure that
the wheel’s specifications match those
of the original wheels.It is recommended you contact your
original equipment or an authorized
tire dealer with any questions you may
have on tire specifications or capability.
Failure to use equivalent replacementtires may adversely affect the safety,
handling, and ride of your vehicle.
WARNING!
 Do not use a tire, wheel size or
rating other than that specified
for your vehicle. Some combina-
tions of unapproved tires and
wheels may change suspension di-
mensions and performance char-
acteristics, resulting in changes to
steering, handling, and braking of
your vehicle. This can cause un-
predictable handling and stress to
steering and suspension compo-
nents. You could lose control and
have a collision resulting in seri-
ous injury or death. Use only the
tire and wheel sizes with load rat-
ings approved for your vehicle.
 Never use a tire with a smaller
load index or capacity, other than
what was originally equipped on
your vehicle. Using a tire with a
smaller load index could result in
tire overloading and failure. You
could lose control and have a col-
lision.
(Continued)
WARNING!(Continued)
 Failure to equip your vehicle with
tires having adequate speed capa-
bility can result in sudden tire fail-
ure and loss of vehicle control.CAUTION!
Replacing original tires with tires of
a different size may result in false
speedometer and odometer read-
ings.
TIRE CHAINS
Use of Security Chain Company
(SCC) Super Z6 low profile (P/N SZ-
139) or equivalent are recommended
on 215/55 R18 95H tires with 18 x
7.0 wheels, 40 mm offset.
154