2012 JEEP WRANGLER headlamp

Entry (RKE) transmitter UNLOCK button. When Driver
Door 1st Press is selected, you must press the RKE
transmitter UNLOCK button twice to unlock the passen-
ger’s doors. WhenAll Doors 1st Press is selected, all of
the doors will unlock on the first press of the RKE
transmitter UNLOCK button. To make your selection,
press and release the SELECT button until “Driver Door
1st Press” or “All Doors 1st Press” appears.
Sound Horn With Lock
When on is selected, a short horn sound will occur when
the RKE transmitter LOCK button is pressed. This feature
may be selected with or without the Flash Lamp with
Lock feature. To make your selection, press and release
the SELECT button until “On” or “Off” appears.
Flash Lamp with Lock
When on is selected, the front and rear turn signals will
flash when the doors are locked or unlocked with the
RKE transmitter. This feature may be selected with or without the Sound Horn with Lock feature selected. To
make your selection, press and release the SELECT
button until “On” or “Off” appears.
Headlamp Off Delay
When this feature is selected, the driver can choose to
have the headlights remain on for 0, 30, 60, or 90 seconds
when exiting the vehicle. To make your selection, press
and release the SELECT button until “0,” “30,” “60,” or
“90” appears.
Headlamps with Wipers
(Available with Auto Headlights Only)
When on is selected, and the headlight switch is in the
AUTO position, the headlights will turn on approxi-
mately 10 seconds after the wipers are turned on. If the
headlights were turned on by this feature they will also
turn off when the wipers are turned off. To make your
selection, press and release the SELECT button until
“ON” or “OFF” appears.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 299

▫Brake System ....................... 535
▫ Automatic Transmission – If Equipped ..... 537
▫ Hydraulic Clutch Fluid – Manual
Transmission ....................... 539
▫ Manual Transmission – If Equipped ....... 539
▫ Transfer Case ....................... 540
▫ Front/Rear Axle Fluid ................. 541
▫ Appearance Care And Protection From
Corrosion .......................... 541
 Fuses .............................. 549
▫ Totally Integrated Power Module ......... 549
 Vehicle Storage ....................... 554
 Replacement Bulbs .................... 555 
Bulb Replacement ..................... 556
▫ Headlamp ......................... 556
▫ Front Park/Turn Signal ................ 557
▫ Front Side Marker .................... 557
▫ Front Fog Lamp ..................... 557
▫ Rear Tail, Stop, Turn Signal, And Backup
Lamp ............................. 558
▫ Center High-Mounted Stop Lamp
(CHMSL) .......................... 558
 Fluid Capacities ...................... 559
 Fluids, Lubricants And Genuine Parts ....... 560
▫ Engine ............................ 560
▫ Chassis ........................... 561
512 MAINTAINING YOUR VEHICLE

Cavity CartridgeFuseMini
Fuse Description
J9 40 Amp Green PZEV Sec Motor/Flex
Fuel
J10 30 Amp Pink Headlamp Wash
Relay/Manifold
Tuning Valve
J11 30 Amp Pink Sway Bar
J12 30 Amp Pink Rear Blower Motor/
Radiator Fan
J13 60 Amp Yellow Ignition Off Draw
(IOD) – Main
J14 40 Amp Green Rear Defroster
J15 40 Amp Green Front Blower
J17 40 Amp Green Starter SolenoidCavity Cartridge
FuseMini
Fuse Description
J18 20 Amp Blue Powertrain Control
Module (PCM) Trans
Range
J19 60 Amp Yellow Radiator Fan
J20 30 Amp Pink Front Wiper LO/HI
J21 20 Amp Blue Front/Rear Washer
J22 — Spare
M1 15 Amp
Blue Center High-Mounted
Stop Light (CHMSL)/
Switch Stop Lamp
Feed
M2 20 Amp
Yellow Relay Trailer Lighting
(Stoplamp)
550 MAINTAINING YOUR VEHICLE

Cavity CartridgeFuseMini
Fuse Description
M24 25 Amp NaturalRear Wiper
M25 20 Amp YellowFuel Pump, Diesel
Lift Pump – Export
Only
M26 10 Amp RedPower Window
Switch, Driver Win-
dow Switch
M27 10 Amp RedIgnition Switch Feed,
Wireless Module
M28 10 Amp RedPowertrain Control
Module
M29 10 Amp RedPowertrain
M30 15 Amp BlueWiper Motor Frt,
J1962 Diagnostic FeedCavity Cartridge
FuseMini
Fuse Description
M31 20 Amp
Yellow Backup Lamps
M32 10 Amp
Red Airbag Controller, TT
EUROPE
M33 10 Amp
Red Powertrain Controller
M34 10 Amp
Red Park Assist, Climate
Control System,
Headlamp Wash,
Compass
M35 10 Amp
Red Heated Mirrors
M36 20 Amp
Yellow Power Outlet
7
MAINTAINING YOUR VEHICLE 553

•Anytime you store your vehicle, or keep it out of
service (i.e., vacation) for two weeks or more, run the
air conditioning system at idle for about five minutes
in the fresh air and high blower setting. This will
ensure adequate system lubrication to minimize the
possibility of compressor damage when the system is
started again.
REPLACEMENT BULBS
Interior LightsBulb Type
Auto. Trans. Indicator Lamp ................. 658
Heater Control Lamps (2) ................... 194
Rocker Switch Indicator Lamp
(Rear Window Defogger, and Rear Wash/Wipe) .... **
Soundbar Dome Lamp ..................... 912
** Bulbs only available from authorized dealer. Exterior Lights
Bulb Type
Backup Lamps (2) ....................... 3157
Center High-Mounted Stop Lamp (1) .........L.E.D.
Fog Lamps ......................... PSX24W
Front Park/Turn Signal Lamps (2) ............3157
Front Side Marker Lamps (2) ................ 168
Headlamps (2) .......................... H13
Rear Stop/Tail/Turn Lamps (2) ..............3157
License Lamp ........................... 194
NOTE: Numbers refer to commercial bulb types that
can be purchased from your local authorized dealer.
If a bulb needs to be replaced, visit your authorized
dealer or refer to the applicable Service Manual.
7
MAINTAINING YOUR VEHICLE 555

BULB REPLACEMENT
NOTE:Lens fogging can occur under certain atmo-
spheric conditions. This will usually clear as atmospheric
conditions change to allow the condensation to change
back into a vapor. Turning the lamps on will usually
accelerate the clearing process.
Headlamp
1. Open hood and support using prop rod.
2. Remove the front grille. Turn the retainers along the
top 1/4 turn counterclockwise and remove.
3. Pull the bottom of the grille away starting at one side
and working toward the other.
4. Turn both park and turn signal socket assemblies 1/4
turn counterclockwise and remove.
5. Remove the four screws holding the metal retaining
ring. 6. Remove the lamp from the collar.
7. Grasp the bulb and turn 1/4 turn counterclockwise.
8. Pull the bulb from the housing.
9. Push connector locking tab to the unlock position.
10. Remove connector from bulb.
11. Push connector onto new bulb base, and push the
connector locking tab to the lock position.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
12. Reinstall bulb housing. Rotate the bulb 1/4 turn
clockwise.
556 MAINTAINING YOUR VEHICLE