2012 JEEP GRAND CHEROKEE light

6. Raise the vehicle by turning the jack screw
clockwise. Raise the vehicle only until the tire
just clears the surface and enough clearance is
obtained to install the spare tire. Minimum tire
lift provides maximum stability.
WARNING!
Raising the vehicle higher than necessary can
make the vehicle less stable. It could slip off
the jack and hurt someone near it. Raise the
vehicle only enough to remove the tire.
7. Remove the lug nuts and wheel. 8. Position the spare wheel/tire on the vehicle
and install the lug nuts with the cone-shaped
end toward the wheel. Lightly tighten the nuts.
CAUTION!
Be sure to mount the spare tire with the valve
stem facing outward. The vehicle could be
damaged if the spare tire is mounted incor-
rectly.
WARNING!
To avoid the risk of forcing the vehicle off the
jack, do not tighten the wheel nuts fully until
the vehicle has been lowered. Failure to follow
this warning may result in personal injury.
9. Lower the vehicle by turning the jack screw
counterclockwise, and remove the jack and
wheel blocks.
10. Finish tightening the lug nuts. Push down
on the wrench while at the end of the handle for
increased leverage. Tighten the lug nuts in a
star pattern until each nut has been tightened
twice. The correct wheel nut tightness is 110 ft
lbs (150 N·m). If in doubt about the correct
tightness, have them checked with a torque
wrench by your authorized dealer or at a ser-
vice station.
11. Lower the jack to the fully closed position
and return it and the tools to the proper posi-
tions in the foam tray.
12. Remove the small center cap and securely
store the road wheel in the cargo area.
Rear Jacking Location
Mounting Spare Tire
286

13. Have the aluminum road wheel and tire
repaired as soon as possible, properly secure
the spare tire with the special wing nut torqued
to 3.7 ft-lbs (5 N·m), reinstall the jack and tool
kit foam tray, and latch the rear load floor cover.
WARNING!
A loose tire or jack, thrown forward in a
collision or hard stop could endanger the
occupants of the vehicle. Always stow the jack
parts and the spare tire in the places provided.
Have the deflated (flat) tire repaired or re-
placed immediately.
Road Tire Installation
1. Mount the road tire on the axle.
2. Install the remaining lug nuts with the cone
shaped end of the nut toward the wheel. Lightly
tighten the lug nuts.
WARNING!
To avoid the risk of forcing the vehicle off the
jack, do not tighten the wheel nuts fully until
the vehicle has been lowered. Failure to follow
this warning may result in personal injury.
3. Lower the vehicle to the ground by turning
the jack handle counterclockwise.
4. Finish tightening the lug nuts. Push down on
the wrench while at the end of the handle for
increased leverage. Tighten the lug nuts in a
star pattern until each nut has been tightened
twice. The correct tightness of each lug nut is
110 ft/lbs (150 N·m). If in doubt about the
correct tightness, have them checked with a
torque wrench by your authorized dealer or
service station. 5. After 25 miles (40 km) check the lug nut
torque with a torque wrench to ensure that all
lug nuts are properly seated against the wheel.
JUMP-STARTINGIf your vehicle has a discharged battery it can
be jump-started using a set of jumper cables
and a battery in another vehicle or by using a
portable battery booster pack. Jump-starting
can be dangerous if done improperly so please
follow the procedures in this section carefully.
NOTE:
When using a portable battery booster pack
follow the manufacturer’s operating instruc-
tions and precautions.
CAUTION!
Do not use a portable battery booster pack or
any other booster source with a system volt-
age greater than 12 Volts or damage to the
battery, starter motor, alternator or electrical
system may occur.
Stowed Spare
287

2. Connect the opposite end of the positive(+)
jumper cable to the positive (+)post of the
booster battery.
3. Connect the negative end (-)of the jumper
cable to the negative (-)post of the booster
battery.
4. Connect the opposite end of the negative (-)
jumper cable to the remote negative (-)post of
the vehicle with the discharged battery.
WARNING!
Do not connect the cable to the negative post
(-) of the discharged battery. The resulting
electrical spark could cause the battery to
explode and could result in personal injury.
5. Start the engine in the vehicle that has the
booster battery, let the engine idle a few min-
utes, and then start the engine in the vehicle
with the discharged battery. Once the engine is started, remove the jumper
cables in the reverse sequence:
6. Disconnect the negative
(-)jumper cable
from the remote negative (-)post of the dis-
charged vehicle.
7. Disconnect the negative end (-)of the
jumper cable from the negative (-)post of the
booster battery.
8. Disconnect the opposite end of the positive
(+) jumper cable from the positive (+)post of
the booster battery.
9. Disconnect the positive (+)end of the
jumper cable from the remote positive (+)post
of the discharged vehicle.
10. Reinstall the protective cover over the re-
mote positive (+)battery post of the discharged
vehicle.
If frequent jump-starting is required to start your
vehicle you should have the battery and charg-
ing system inspected at your authorized dealer.
CAUTION!
Accessories that can be plugged into the
vehicle power outlets draw power from the
vehicle’s battery, even when not in use (i.e.,
cellular phones, etc.). Eventually, if plugged in
long enough, the vehicle’s battery will dis-
charge sufficiently to degrade battery life
and/or prevent the engine from starting.
FREEING A STUCK VEHICLEIf the vehicle becomes stuck in snow, sand or
mud, it can often be moved by a rocking
motion. Move the shift lever rhythmically be-
tween DRIVE and REVERSE while applying
slight pressure to the accelerator. In general,
the least amount of accelerator pedal pressure
to maintain the rocking motion without spinning
the wheels or racing the engine is most effec-
tive.
289

ONBOARD DIAGNOSTIC SYSTEM –
OBD II
Your vehicle is equipped with a sophisticated
onboard diagnostic system called OBD II. This
system monitors the performance of the emis-
sions, engine, and automatic transmission con-
trol systems. When these systems are operat-
ing properly, your vehicle will provide excellent
performance and fuel economy, as well as
engine emissions well within current govern-
ment regulations.
If any of these systems require service, the
OBD II system will turn on the “Malfunction
Indicator Light” (MIL). It will also store diagnos-
tic codes and other information to assist your
service technician in making repairs. Although
your vehicle will usually be drivable and not
need towing, see your authorized dealer for
service as soon as possible.
CAUTION!
•Prolonged driving with the MIL on could
cause further damage to the emission con-
trol system. It could also affect fuel
economy and drivability. The vehicle must
be serviced before any emissions tests can
be performed.
• If the MIL is flashing while the engine is
running, severe catalytic converter damage
and power loss will soon occur. Immediate
service is required.
Loose Fuel Filler Cap Message
If the vehicle diagnostic system
determines that the fuel filler cap is
loose, improperly installed, or
damaged, a loose gascap indica-
tor will display in the EVIC telltale
display area. Refer to “Electronic
Vehicle Information Center (EVIC)” in “Under-
standing Your Instrument Panel” for further in-
formation. Tighten the fuel filler cap properly
and press the SELECT button to turn off the message. If the problem continues, the mes-
sage will appear the next time the vehicle is
started.
A loose, improperly installed, or damaged fuel
filler cap may also turn on the Malfunction
Indicator Light (MIL).
REPLACEMENT PARTSUse of genuine MOPAR
parts for normal/
scheduled maintenance and repairs is highly
recommended to ensure the designed perfor-
mance. Damage or failures caused by the use
of non-MOPAR parts for maintenance and
repairs will not be covered by the manufactur-
er’s warranty.
MAINTENANCE PROCEDURESThe pages that follow contain the required
maintenance services determined by the engi-
neers who designed your vehicle.
Besides those maintenance items specified in
the fixed maintenance schedule, there are
other components which may require servicing
or replacement in the future.
301

Fluid Level Check – 5.7L Engine
Check the fluid level while the transmission is at
normal operating temperature. This occurs af-
ter at least 15 miles (25 km) of driving. At
normal operating temperature the fluid cannot
be held comfortably between the fingertips.
To check the fluid level properly, the following
procedure must be used:
1. Operate the engine at idle speed and nor-
mal operating temperature.
2. The vehicle must be on level ground.
3. Fully apply the parking brake, and press the
brake pedal.
4. Place the shift lever momentarily in each
gear position ending with the shift lever in
PARK.
5. Remove the dipstick, wipe it clean and
reinsert it until seated.6. Remove the dipstick again, and note the
fluid level on both sides. The fluid level should
be between the “HOT” (upper) reference holes
on the dipstick at normal operating tempera-
ture. The fluid level is only valid if there is a solid
coating of oil on both sides of the dipstick. If the
fluid is low, add as required into the dipstick
tube.
Do not overfill. After adding any quantity
of oil through the oil fill tube, wait a minimum of
two minutes for the oil to fully drain into the
transmission before rechecking the fluid level.
NOTE:
If it is necessary to check the transmission
below the operating temperature, the fluid
level should be between the two “COLD”
(lower) holes on the dipstick with the fluid at
approximately 70°F (21°C) (room tempera-
ture). If the fluid level is correctly estab-
lished at room temperature, it should be
between the “HOT” (upper) reference holes
when the transmission reaches 180°F
(82°C). Remember it is best to check the
level at the normal operating temperature.CAUTION!
Be aware that if the fluid temperature is below
50°F (10°C) it may not register on the dipstick.
Do not add fluid until the temperature is
elevated enough to produce an accurate
reading.
7. Check for leaks. Release parking brake.
To prevent dirt and water from entering the
transmission after checking or replenishing
fluid, make certain that the dipstick cap is
properly reseated. It is normal for the dipstick
cap to spring back slightly from its fully seated
position, as long as its seal remains engaged in
the dipstick tube.
Appearance Care And Protection
From Corrosion
Protection Of Body And Paint From
Corrosion
Vehicle body care requirements vary according
to geographic locations and usage. Chemicals
that make roads passable in snow and ice, and
those that are sprayed on trees and road
315

•Use MOPAR Touch Up Paint or equivalent
on scratches or chips as soon as possible.
Your authorized dealer has touch up paint to
match the color of your vehicle.
Wheel And Wheel Trim Care
All wheels and wheel trim, especially aluminum
and chrome-plated wheels should be cleaned
regularly with a mild soap and water to prevent
corrosion. To remove heavy soil, use MOPAR
Wheel Cleaner or select a nonabrasive, non-
acidic cleaner. Do not use scouring pads, steel
wool, a bristle brush or metal polishes. Only
MOPAR cleaners or equivalent are recom-
mended. Do not use oven cleaner. Avoid auto-
matic car washes that use acidic solutions or
harsh brushes that may damage the wheels’
protective finish.
Stain Repel Fabric Cleaning Procedure – If
Equipped
Stain Repel seats may be cleaned in the follow-
ing manner:
• Remove as much of the stain as possible by
blotting with a clean, dry towel.
• Blot any remaining stain with a clean, damp
towel. •
For tough stains, apply MOPAR Total Clean
or a mild soap solution to a clean, damp
cloth and remove the stain. Use a fresh,
damp towel to remove soap residue.
• For grease stains, apply MOPAR Multi-
Purpose Cleaner or equivalent to a clean,
damp cloth and remove the stain. Use a
fresh, damp towel to remove soap residue.
• Do not use any harsh solvents or any other
form of protectants on Stain Repel products.
Interior Care
Use MOPAR Total Clean or equivalent to clean
fabric upholstery and carpeting.
Interior Trim should be cleaned starting with a
damp cloth, a damp cloth with MOPAR Total
Clean or equivalent, then MOPAR Spot & Stain
Remover or equivalent, if absolutely necessary.
Do not use harsh cleaners or Armor All . Use
MOPAR Total Clean or equivalent to clean
vinyl upholstery.
Leather Seat Care And Cleaning
MOPAR Total Clean or equivalent is specifi-
cally recommended for leather upholstery. Your leather upholstery can be best preserved
by regular cleaning with a damp soft cloth.
Small particles of dirt can act as an abrasive
and damage the leather upholstery and should
be removed promptly with a damp cloth. Stub-
born soils can be removed easily with a soft
cloth and MOPAR
Total Clean or equivalent.
Care should be taken to avoid soaking your
leather upholstery with any liquid. Please do
not use polishes, oils, cleaning fluids, solvents,
detergents, or ammonia-based cleaners to
clean your leather upholstery. Application of a
leather conditioner is not required to maintain
the original condition.
WARNING!
Do not use volatile solvents for cleaning pur-
poses. Many are potentially flammable, and if
used in closed areas, they may cause respi-
ratory harm.
Cleaning Headlights
Your vehicle has plastic headlights that are
lighter and less susceptible to stone breakage
than glass headlights.
317

Plastic is not as scratch-resistant as glass and
therefore different lens cleaning procedures
must be followed.
To minimize the possibility of scratching the
lenses and reducing light output, avoid wiping
with a dry cloth. To remove road dirt, wash with
a mild soap solution followed by rinsing.
Do not use abrasive cleaning components,
solvents, steel wool or other aggressive mate-
rial to clean the lenses.
Glass Surfaces
All glass surfaces should be cleaned on a
regular basis with MOPARGlass Cleaner or
any commercial household-type glass cleaner.
Never use an abrasive type cleaner. Use cau-
tion when cleaning inside rear windows
equipped with electric defrosters. Do not use
scrapers or other sharp instruments which may
scratch the elements.
When cleaning the rearview mirror, spray
cleaner on the towel or rag that you are using.
Do not spray cleaner directly on the mirror. Cleaning Plastic Instrument Cluster Lenses
The lenses in front of the instruments in this
vehicle are molded in clear plastic. When
cleaning the lenses, care must be taken to
avoid scratching the plastic.
1. Clean with a wet soft rag. A mild soap
solution may be used, but do not use high
alcohol content or abrasive cleaners. If soap is
used, wipe clean with a clean damp rag.
2. Dry with a soft cloth.
Seat Belt Maintenance
Do not bleach, dye or clean the belts with
chemical solvents or abrasive cleaners. This
will weaken the fabric. Sun damage will also
weaken the fabric.
If the belts need cleaning, use MOPAR
Total
Clean, a mild soap solution, or lukewarm water.
Do not remove the belts from the vehicle to
wash them. Dry with a soft cloth.
Replace the belts if they appear frayed or worn
or if the buckles do not work properly.FUSES
Totally Integrated Power Module
The Totally Integrated Power Module is located
in the engine compartment. This center con-
tains cartridge fuses and mini fuses. A descrip-
tion of each fuse and component may be
stamped on the inside cover, otherwise the
cavity number of each fuse is stamped on the
inside cover that corresponds to the following
chart.
Totally Integrated Power Module
318

Cavity Car-tridgeFuse Mini
Fuse Description
J01 40 Amp Green Air Suspension
J02 30 Amp Pink Power Liftgate
Module
J03 30 Amp Pink Trailer Tow
J04 25 Amp Natural Driver Door
Node
J05 25 Amp Natural Passenger Door
Node
J06 40 Amp Green Antilock Brakes
Pump/Stability
Control System
J07 30 Amp Pink Antilock Brakes
Valve/Stability
Control System
J08 40 Amp Green Power Seat
J09 30 Amp Pink E-Brake
J10 30 Amp Pink Headlamp Wash
Relay ContactCavity Car-
tridgeFuse Mini
Fuse Description
J11 30 Amp Pink Drive Train Con-
trol Module
J12 30 Amp Pink Rear Defroster
J13 60 Amp Yellow Main Ignition Off
Draw (IOD)
J14 20 Amp Blue Trailer Tow
Lamps/Park
Lamps
J15 40 Amp Green Front Cabin Fan/
Blower
J17 40 Amp Green Starter Motor
Solenoid
J18 20 Amp Blue Powertrain Con-
trol Module/
Powertrain Con-
trol Module
Transmission
RangeCavity Car-
tridgeFuse Mini
Fuse Description
J19 60 Amp Yellow Radiator Fan
Motor HI/
Radiator Fan
Motor Low
J20 30 Amp Pink Front Wiper
J21 20 Amp Blue Front/Rear
Washer Control
J22 25 Amp Natural Sunroof Module
M1 15 Amp
Blue Stop Lamps
M2 20 Amp
Yellow Electronic Limit
Slip Differential/
Air Suspension
M3 20 Amp
Yellow Liftgate/Headrest
M5 25 Amp
Natural 115V AC Power
Inverter
M6 20 Amp
Yellow Cigar Lighter
319