2012 INFINITI G37 ECU

Black plate (54,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-32 Safety — Seats, seat belts and supplemental restraint system7. Check to make sure that the child
restraint is properly secured prior to
each use. If the seat belt is not locked,
repeat steps 1 through 6.
After the child restraint is removed and the
seat belt fully retracted, the ALR mode
(child restraint mode) is canceled.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING LATCH GUID-C7CEB4CB-D6DD-4996-BA6E-023C4B2CA773
Refer to all Warnings and Cautions in the
“ Child safety ” and “ Child restraints ” sec-
tions before installing a child restraint.
Follow these steps to install a forward-
facing child restraint using the LATCH
system:
1. Position the child restraint on the seat.
Always follow the child restraint man-
ufacturer ’ s instructions. SSS0645
Forward-facing web-mounted — step 2
2. Secure the child restraint anchor at-
tachments to the LATCH lower anchors.
Check to make sure the LATCH attach-
ment is properly attached to the lower
anchors.
If the child restraint is equipped with a
top tether strap, route the top tether
strap and secure the tether strap to the
tether anchor point. See “ Installing top
tether strap ” (P.1-37). Do not install
child restraints that require the use of a
top tether strap in seating positions
that do not have a top tether anchor. SSS0646
Forward-facing rigid-mounted — step 3
3. The back of the child restraint should
be secured against the vehicle seat-
back.
If the seating position does not have an
adjustable headrest and it is interfering
with the proper child restraint fit, try
another seating position or a different
child restraint.

Black plate (55,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SSS0647
Forward-facing — step 4
4. For child restraints that are equipped
with webbing-mounted attachments,
remove any additional slack from the
anchor attachments. Press downward
and rearward firmly in the center of the
child restraint with your knee to com-
press the vehicle seat cushion and
seatback while tightening the webbing
of the anchor attachments.
5. Tighten the tether strap according to
the manufacturer ’ s instructions to re-
move any slack. SSS0638
Forward-facing — step 6
6. After attaching the child restraint, test
it before you place the child in it. Push
it from side to side while holding the
child restraint near the LATCH attach-
ment path. The child restraint should
not move more than 1 inch (25 mm),
from side to side. Try to tug it forward
and check to see if the LATCH attach-
ment holds the restraint in place. If the
restraint is not secure, tighten the
LATCH attachment as necessary, or
put the restraint in another seat and
test it again. You may need to try a
different child restraint. Not all child
restraints fit in all types of vehicles. 7. Check to make sure the child restraint
is properly secured prior to each use. If
the child restraint is loose, repeat steps
1 through 6.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT
BELTS GUID-B0438CCC-C788-4E94-8FA4-DB4F26EE0A33
WARNING The three-point seat belt with Automatic
Locking Retractor (ALR) must be used when
installing a child restraint. Failure to use the
ALR mode will result in the child restraint
not being properly secured. The restraint
could tip over or be loose and cause injury
to a child in a sudden stop or collision. Also,
it can change the operation of the front
passenger air bag. See “ Front passenger air
bag and status light ” (P.1-49).
Safety — Seats, seat belts and supplemental restraint system
1-33

Black plate (56,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-34 Safety — Seats, seat belts and supplemental restraint system SSS0640
Forward-facing (front passenger seat) —
step 1
Refer to all Warnings and Cautions in the
“ Child safety ” and “ Child restraints ” sec-
tions before installing a child restraint.
Follow these steps to install a forward-
facing child restraint using the vehicle seat
belt in the rear seats or in the front
passenger seat:
1. If you must install a child restraint in
the front seat, it should be placed in a
forward-facing direction only. Move the
seat to the rearmost position. Child
restraints for infants must be used in
the rear-facing direction and, therefore,
must not be used in the front seat. 2. Position the child restraint on the seat.
Always follow the child restraint man-
ufacturer ’ s instructions.
The back of the child restraint should
be secured against the vehicle seat-
back.
If necessary, adjust or remove the head
restraint to obtain the correct child
restraint fit. If the head restraint is
removed, store it in a secure place. Be
sure to reinstall the head restraint
when the child restraint is removed.
See “ Head restraints ” (P.1-9) for head
restraint adjustment, removal and in-
stallation information.
If the seating position does not have an
adjustable head restraint and it is
interfering with the proper child re-
straint fit, try another seating position
or a different child restraint. SSS0360B
Forward-facing — step 3
3. Route the seat belt tongue through the
child restraint and insert it into the
buckle until you hear and feel the latch
engage. Be sure to follow the child
restraint manufacturer ’ s instructions
for belt routing.
If the child restraint is equipped with a
top tether strap, route the top tether
strap and secure the tether strap to the
tether anchor point (rear seat installa-
tion only). See “ Installing top tether
strap ” (P.1-37). Do not install child
restraints that require the use of a top
tether strap in seating positions that do
not have a top tether anchor.

Black plate (58,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-36 Safety — Seats, seat belts and supplemental restraint system SSS0641
Forward-facing — step 8
8. After attaching the child restraint, test
it before you place the child in it. Push
it from side to side while holding the
child restraint near the seat belt path.
The child restraint should not move
more than 1 inch (25 mm), from side to
side. Try to tug it forward and check to
see if the belt holds the restraint in
place. If the restraint is not secure,
tighten the seat belt as necessary, or
put the restraint in another seat and
test it again. You may need to try a
different child restraint. Not all child
restraints fit in all types of vehicles. 9. Check to make sure the child restraint
is properly secured prior to each use. If
the seat belt is not locked, repeat steps
2 through 8.
SSS0676
Forward-facing — step 10
10. If the child restraint is installed in the
front passenger seat, place the ignition
switch in the ON position. The front
passenger air bag status light
should illuminate. If this light is not
illuminated, see “ Front passenger air
bag and status light ” (P.1-49). Move
the child restraint to another seating
position. Have the system checked by
an INFINITI retailer.
After the child restraint is removed and the
seat belt is fully retracted, the ALR mode
(child restraint mode) is canceled.

Black plate (59,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SSS0791
Sedan
SSS0790
Coupe INSTALLING TOP TETHER STRAP GUID-C9A5E577-AFA4-46B6-97E2-D077C8A3DBAB
First, secure the child restraint with the
LATCH lower anchors (rear outboard seat
positions only) or the seat belt, as applic-
able.
1. Flip up the anchor cover from the
anchor point which is located directly
behind the child seat.
2. Position the top tether strap over the
top of the seatback.
3. Secure the tether strap to the tether
anchor point on the rear parcel shelf.
4. Refer to the appropriate child restraint
installation procedure steps in this
section before tightening the tether
strap.
If you have any questions when installing
a top tether strap, consult your INFINITI
retailer for details. BOOSTER SEATS GUID-F369878B-DD25-483E-8198-275B4D15BF3F
Precautions on booster seats GUID-25C42A16-09BB-45D5-A28E-6C3CA2A753FF
WARNING If a booster seat and seat belt are not used
properly, the risk of a child being injured in
a sudden stop or collision greatly increases:
. Make sure the shoulder portion of the
belt is away from the child ’ s face and
neck and the lap portion of the belt does
not cross the stomach.
. Make sure the shoulder belt is not
behind the child or under the child ’ s
arm.
. A booster seat must only be installed in
a seating position that has a lap/
shoulder belt.
Safety — Seats, seat belts and supplemental restraint system
1-37

Black plate (62,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-40 Safety — Seats, seat belts and supplemental restraint system LRS0454
Front passenger position
3. The booster seat should be positioned
on the vehicle seat so that it is stable.
If necessary, adjust or remove the head
restraint to obtain the correct booster
seat fit. If the head restraint is
removed, store it in a secure place. Be
sure to reinstall the head restraint
when the booster seat is removed.
See “ Head restraints ” (P.1-9) for head
restraint, removal and installation in-
formation.
If the seating position does not have an
adjustable head restraint and it is
interfering with the proper booster seat fit, try another seating position or a
different booster seat.
4. Position the lap portion of the seat belt
low and snug on the child ’ s hips. Be
sure to follow the booster seat manu-
facturer ’ s instructions for adjusting the
seat belt routing.
5. Pull the shoulder belt portion of the
seat belt toward the retractor to take up
extra slack. Be sure the shoulder belt is
positioned across the top, middle por-
tion of the child ’ s shoulder. Be sure to
follow the booster seat manufacturer ’ s
instructions for adjusting the seat belt
routing.
6. Follow the warnings, cautions and
instructions for properly fastening a
seat belt shown in “ Seat belts ” (P.1-
14). SSS0676
7. If the booster seat is installed in the
front passenger seat, push the ignition
switch to the ON position. The front
passenger air bag status light
may
or may not illuminate depending on the
size of the child and the type of booster
seat used. See “ Front passenger air
bag and status light ” (P.1-49).

Black plate (72,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-50 Safety — Seats, seat belts and supplemental restraint systemas outlined in this manual should not
cause the passenger air bag to be auto-
matically turned OFF. For small adults it
may be turned OFF, however, if the
occupant does not sit in the seat properly
(for example, by not sitting upright, by
sitting on an edge of the seat, or by
otherwise being out of position), this could
cause the sensor to turn the air bag OFF.
Always be sure to be seated and wearing
the seat belt properly for the most effective
protection by the seat belt and supple-
mental air bag.
INFINITI recommends that pre-teens and
children be properly restrained in a rear
seat. INFINITI also recommends that appro-
priate child restraints and booster seats be
properly installed in a rear seat. If this is
not possible, the occupant classification
sensor is designed to operate as described
above to turn the front passenger air bag
OFF for specified child restraints. Failing to
properly secure child restraints and to use
the ALR mode (child restraint mode) may
allow the restraint to tip or move in an
accident or sudden stop. This can also
result in the passenger air bag inflating in
a crash instead of being OFF. (See “ Child
restraints ” (P.1-23) for proper use and installation.)
If the front passenger seat is not occupied,
the passenger air bag is designed not to
inflate in a crash. However, heavy objects
placed on the seat could result in air bag
inflation, because of the object being
detected by the occupant classification
sensor. Other conditions could also result
in air bag inflation, such as if a child is
standing on the seat, or if two children are
on the seat, contrary to the instructions in
this manual. Always be sure that you and
all vehicle occupants are seated and
restrained properly.
Using the passenger air bag status light,
you can monitor when the front passenger
air bag is automatically turned OFF with the
seat occupied. The light will not illuminate
when the front passenger seat is unoccu-
pied.
If an adult occupant is in the seat but the
passenger air bag status light is illumi-
nated (indicating that the air bag is OFF), it
could be that the person is a small adult,
or is not sitting on the seat properly.
If a child restraint must be used in the front
seat, the passenger air bag status light
may or may not be illuminated, depending
on the size of the child and the type of child restraint being used. If the passenger
air bag status light is not illuminated
(indicating that the air bag might inflate
in a crash), it could be that the child
restraint or seat belt is not being used
properly. Make sure that the child restraint
is installed properly, the seat belt is used
properly and the occupant is positioned
properly. If the passenger air bag status
light is still not illuminated, reposition the
occupant or child restraint in a rear seat.
If the passenger air bag status light will not
illuminate even though you believe that the
child restraint, the seat belts and the
occupant are properly positioned, the
system may be sensing an unoccupied
seat (in which case the air bag is OFF). Your
INFINITI retailer can check that the system
is OFF by using a special tool. However,
until you have confirmed with your retailer
that your air bag is working properly,
reposition the occupant or child restraint
in a rear seat.
The INFINITI advanced air bag system and
passenger air bag status light will take a
few seconds to register a change in the
passenger seat status. However, if the seat
becomes unoccupied, the air bag status
light will remain off.

Black plate (79,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2 Instruments and controls Cockpit ................................................................... 2-3
Instrument panel .................................................... 2-4
Meters and gauges ................................................. 2-6
Speedometer and odometer ............................... 2-7
Tachometer ......................................................... 2-8
Engine coolant temperature gauge ..................... 2-8
Fuel gauge ......................................................... 2-9
Compass (if so equipped) ....................................... 2-9
Zone variation change procedure ...................... 2-11
Warning/indicator lights and
audible reminders ................................................ 2-12
Checking bulbs ................................................. 2-12
Warning lights .................................................. 2-12
Indicator lights ................................................. 2-18
Audible reminders ............................................ 2-19
Dot matrix liquid crystal display ........................... 2-20
Indicators for operation .................................... 2-22
Indicators for maintenance ............................... 2-24
Trip computer ................................................... 2-26
Security systems .................................................. 2-28
Vehicle Security System ................................... 2-28
INFINITI Vehicle Immobilizer System ................. 2-30
Windshield wiper and washer switch .................... 2-31
Rain-sensing auto wiper system
(if so equipped) ................................................ 2-33 Rear window and outside mirror
defroster switch ................................................... 2-34
Headlight and turn signal switch .......................... 2-34
Xenon headlights ............................................ 2-34
Headlight switch ............................................. 2-35
Turn signal switch ........................................... 2-38
Fog light switch .............................................. 2-39
Hazard warning flasher switch ............................. 2-39
Horn .................................................................... 2-40
Heated seats (if so equipped) .............................. 2-40
SNOW mode switch (if so equipped) .................... 2-41
Vehicle Dynamic Control (VDC) OFF switch ............ 2-42
Clock .................................................................... 2-42
Adjusting the time .......................................... 2-42
Power outlet ........................................................ 2-43
Cigarette lighter and ashtrays (if so equipped) ....... 2-44
Front ............................................................... 2-44
Rear ................................................................ 2-44
Storage ................................................................ 2-45
Cup holders .................................................... 2-45
Sunglasses holder ......................................... 2-47
Glove box ....................................................... 2-47
Console box .................................................... 2-48
Card holder (if so equipped) ........................... 2-49
Storage box (if so equipped) ........................... 2-50>