2012 HYUNDAI I40 maintenance

Downloaded from www.Manualslib.com manuals search engine Maintenance
90
7
Vehicle condition H1H2H3W1 W2W3
Without driver 736 (28.9) 688 (27.0) 393 (15.4) 1,472 (57.9) 1,186 (46.6) 1508 (59.3)
With driver 728 (28.6) 680 (26.7) 385 (15.1) 1,472 (57.9) 1,186 (46.6) 1508 (59.3)
Unit: mm (in)
Aiming point
< Ground Height >
H1 : Height between the head lamp bulb center and ground (Low beam)
H2 : Height between the head lamp bulb center and ground (High beam)
H3 : Height between the fog lamp bulb center and ground
W1 : Distance between the two head lamp bulbs centers (Low beam)
W2 : Distance between the two head lamp bulbs centers (High beam)
W3 : Distance between the two fo
g lamp bulbs centers
< Distance between lamps >

Downloaded from www.Manualslib.com manuals search engine 791
Maintenance
OMD051054L
Head lamp low beam (driver’s side)
1. Turn the low beam on without driver aboard.
2. The cut-off line should be projected in the cut-off line shown in the picture.
3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.
4. If head lamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.

Downloaded from www.Manualslib.com manuals search engine Maintenance
92
7
OMD051055L
Head lamp low beam (front passenger’s side)
1. Turn the low beam on without driver aboard.
2. The cut-off line should be projected in the cut-off line shown in the picture.
3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.
4. If head lamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.

Downloaded from www.Manualslib.com manuals search engine 793
Maintenance
OMD051056L
Front fog light
1. Turn the front fog lamp on without the driver aboard.
2. The cut-off line should be projected in the allowable range (shaded region).

Downloaded from www.Manualslib.com manuals search engine Maintenance
94
7
Side repeater light bulb replace-
ment
If the light bulb does not operate, have
the vehicle checked by an authorized
HYUNDAI dealer.
Rear combination light bulb
replacement
(1) Stop light
(2) Rear turn signal light
(3) Back-up light
(4) Tail light
(5) Rear fog light (if equipped)
Outside light
Rear turn signal light
1. Turn off the engine.
2. Open the tailgate.
3. Remove the cover.
OVF071036
OVF071037
OVF071038
OVF071035

Downloaded from www.Manualslib.com manuals search engine 795
Maintenance
4. Loosen the light assembly retainingscrews with a cross-tip screwdriver.
5. Remove the rear combination light assembly from the body of the vehicle.
6. Remove the socket from the assemblyby turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
7. Remove the bulb from the socket by pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket. Pull
the bulb out of the socket.
8. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place.
9. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
10. Reinstall the light assembly to the body of the vehicle.
Inside light
1. Turn off the engine.
2. Open the tailgate.
3. Remove the service cover using a flat-blade screwdriver.
OVF071040OVF071039

Downloaded from www.Manualslib.com manuals search engine Maintenance
96
7
Back-up light
4. Remove the socket from the assembly
by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
5. Remove the bulb from the socket by pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket. Pull
the bulb out of the socket.
6. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place. 7. Install the socket in the assembly by
aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
8. Install the service cover by putting it into the service hole.
Rear fog light
4. Remove the bulb-socket from theassembly by turning the socket count-
er clockwise until the tabs on the sock-
et align with the slots on the assembly.
5. Install the new bulb-socket into the assembly by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the assembly and
turn the socket clockwise.
OVF071041
B
B
B
B
a
a
a
a
c
c
c
c
k
k
k
k
-
-
u
u
u
u
p
p
p
p



l
l
l
l
i
i
i
i
g
g
g
g
h
h
h
h
t
t
t
t
OVF071041
R
R
R
R
e
e
e
e
a
a
a
a
r
r
r
r



f
f
f
f
o
o
o
o
g
g
g
g




l
l
l
l
i
i
i
i
g
g
g
g
h
h
h
h
t
t
t
t

Downloaded from www.Manualslib.com manuals search engine 797
Maintenance
High mounted stop light bulb
replacement (if equipped)
If the light does not operate, have the
vehicle checked by an authorized
HYUNDAI dealer.
License plate light bulb replace-
ment
1. Turn off the engine.
2. Loosen the retaining screws with aphilips head screwdriver.
3. Remove the bulb assembly by turning it counterclockwise.
4. Remove the bulb by pulling it straight out.
5. Install a new bulb.
6. Reinstall the bulb assembly securely with the retaining screws.
OVF071043OVF071042