2012 HONDA ACCORD reset

This indicator comes on f or a f ew
seconds when you turn the ignition
switch to the ON (II) position. It
remindsyouthatitistimetotake
your vehicle in f or scheduled
maintenance. The maintenance main
items and sub items will be displayed
in the inf ormation display. See pagef or more inf ormation on the
Maintenance Minder .
This indicator goes of f when your
dealer resets it after completing the
required maintenance service.
This indicator comes on when you
turn on the cruise control system by
pressing the CRUISE button (see
page ).
This indicator comes on when you
set the cruise control. See page
f or inf ormation on operating the
cruise control.
This indicator comes on when you
turn on the f og lights. For more
inf ormation, see page . This indicator comes on brief ly when
you turn the ignition switch to the
ON (II) position. It will then go of f if
you have inserted a properly coded
ignition key. If it is not a properly
coded key, the indicator will blink,
and the engine’s f uel system will be
disabled (see page ).
This indicator comes on when the
washer f luid level is low. Add washer
fluidwhenyouseethisindicator
(see page ).
255
255
74335
79
350
If equipped Canadian models only
Immobilizer System
Indicator
Maintenance Minder
Indicator
Cruise Control Indicator Washer Level Indicator
Cruise Control Main
Indicator
Fog L ight Indicator
Instrument Panel Indicators
64
TM
Main MenuTable of Contents

Î
ÎIf equipped
:
Gauges
Inst rument s and Cont rols
65
ODOMETER/CHECK FUEL CAP MESSAGE SPEEDOMETER
U.S. model is shown. OUTSIDE TEMPERATURE INDICATOR FUEL GAUGE
INFORMATION DISPLAY TRIP METER
TEMPERATURE GAUGE
SELECT/RESET KNOB
TACHOMETER
Main MenuTable of Contents

The odometer shows the total
distance your vehicle has been
driven. It measures miles in U.S.
models and kilometers in Canadian
models. It is illegal under U.S.
f ederal law and Canadian provincial/
territorial regulations to disconnect,
reset, or alter the odometer with the
intent to change the number of miles
or kilometers indicated.
The inf ormation display shows the
odometer, trip meter, engine oil lif e,
outside temperature (if equipped),
and maintenance item code(s). To switch the display, press and
release the select/reset knob
repeatedly. When you turn the
ignition switch to the ON (II)
position, your last selection is
displayed.
Gauges
Odometer
Inf ormation Display
66
INFORMATION DISPLAY TRIP METER A
TRIP METER B
ENGINE OIL LIFE
OUTSIDE
TEMPERATURE
INDICATOR
: Press the select/reset knob.
U.S. model with outside temperature indicator is shown. ODOMETER
Main MenuTable of Contents

The select/reset knob on the
instrument panel controls the
brightness of the instrument panel
lights. Turn the knob to adjust the
brightness with the ignition switch in
the ON (II) position and the parking
lights on.
You can use the f og lights only when
the headlights are on low beam.
Turn the f og lights on and of f by
turning the switch next to the
headlight switch. With the light switch in the AUTO
position, you can also use the f og
lights when the headlights turn on
automatically. They will go of f when
the headlights turn of f , or the
daytime running lights are on.If equipped
Fog L ights, Instrument Panel Brightness
Fog L ights
Instrument Panel Brightness
74
SELECT/RESET KNOB
V6 model is shown.
Main MenuTable of Contents

Push the button between the center
vents to turn on the hazard warning
lights (f our-way f lashers). This
causes all f our outside turn signals
and both turn indicators in the
instrument panel to f lash. Use the
hazard warning lights if you need to
park in a dangerous area near heavy
traf f ic, or if your vehicle is disabled.
The instrument panel will illuminate
with reduced brightness when you
unlock and open the driver’s door.
The brightness will increase slightly
when you insert the key in the
ignitionswitch,thengotonormal
brightness when you turn the
ignition switch to the ON (II)
position.
If you insert the key but do not turn
the ignition switch to the ON (II)
position, the illumination turns of f in
about 10 seconds.
If you do not insert the key in the
ignition switch af ter opening the
driver’s door, the illumination turns
of f about 30 seconds af ter you close
the door.
The level of brightness is shown on
the inf ormation display while you
adjust it. It goes out about 5 seconds
af ter you f inish adjusting.
To reduce glare at night, the
instrument panel illumination dims
when you turn the light switch to
or . Turning the select/
reset knob to the right until you hear
a beep will cancel the reduced
brightness. Hazard Warning Button
Instrument Panel Brightness, Hazard Warning Button
Inst rument s and Cont rols
75
BRIGHTNESS LEVEL
U.S. model is shown.
Main MenuTable of Contents

Playing the FM/A M Radio (Models without navigation system)
Without XMRadioWith XMRadio
EX,EX-L,CanadianSE,andV6models
140
MENU BUTTON
TITLE
BUTTON
MENU BUTTON AM
BUTTON
U.S. models are shown. RETURN BUTTON
A.SEL
(AUTO SELECT)
BUTTON
SKIP BAR
SCAN
BUTTON
FOLDER BAR
FM
BUTTON
AM
BUTTON
SELECTOR KNOB A.SEL
(AUTO SELECT)
BUTTONTITLE
BUTTON
SKIP BAR
SELECTOR KNOB
FM
BUTTON
PRESET
BUTTONS SCAN
BUTTON
CATEGORY BAR PRESET
BUTTONS
RETURN BUTTON
POWER/VOLUME KNOB
POWER/VOLUME KNOB
Main MenuTable of Contents

Playing the FM/A M Radio (Models without navigation system)
LX,LX-P,andU.S.SEmodels
Without XMRadio
Features
141
PRESET BUTTONS
A.SEL (AUTO SELECT)
BUTTON
TITLE BUTTON
SKIP BAR
AM BUTTON
FM BUTTON
SCAN BUTTON
FOLDER BAR
MENU BUTTON
SELECTOR KNOB
RETURN BUTTON POWER/VOLUME KNOB
Main MenuTable of Contents

µµ µ
The band and f requency that the
radio was last tuned to are displayed.
To change bands, press the AM or
FM button. On the FM band, ST will
be displayed if the station is
broadcasting in stereo. Stereo
reproduction in AM is not available.
On the AM band, AM noise
reduction turns on automatically.
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
power/volume knob or the AM or
FM button. Adjust the volume by
turning the power/volume knob.
You can use any of f ive methods to
f ind radio stations on the selected
band: tune, skip, scan, the preset
buttons, and auto select.
The skip f unction searches
up and down f rom the current
f requency to f ind a station with a
strong signal. To activate it, press
and hold the or side of the
SKIP bar until you hear a beep, then
release it.
On the FM band, you can also use
the f eatures provided by the radio
data system (RDS). For more
inf ormation on the RDS, see page
.
Use the selector knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a
lower f requency. The scan f unction samples
all stations with strong signals on the
selected band. To activate it, press
the SCAN button, then release it.
You will see SCAN in the display.
When the system finds a strong
signal, it will stop and play that
station f or about 10 seconds.
If you do nothing, the system will
scan f or the next strong station and
play it f or 10 seconds. When it plays
a station that you want to listen to,
press the SCAN button again.
144
To Select a Station
To Play the Radio
SK IP
TUNE SCAN
Playing the FM/A M Radio (Models without navigation system)
142
Main MenuTable of Contents