2012 FIAT FREEMONT window

** If the car is used for less than 10 000 km per year, it
is necessary to replace engine oil and cartridge every
12 months.
*** The actual interval for replacement of engine oil
and cartridge depends by vehicle usage conditions and
is shown through a gauge or a message (if available) on
the dashboard or at least every 24 months.
Failure to perform the required mainte-
nance items may result in damage to the
vehicle.
Regular Checks
Every 1,000 km or before long journeys, check and top
up the following if necessary:
• engine coolant fluid, brake fluid, windshield washer fluid and power steering fluid;
• tire pressure and condition;
• operation of lighting system (headlights, direction indicators, hazard lights, etc.);
• operation of the windshield wiper/washer system, position and wear of windshield/rear window wiper
blades;
• Check and add, if required, the engine oil level every 3,000 km. Use Of The Car Under Heavy Conditions
If you use the car mainly under one of the followingconditions:
• trailer or caravan towing;
• dusty roads;
• short (less than 7-8 km) and repeated journeys in
sub-zero temperatures;
• frequent engine idling, travelling long distances at low speeds or long term inactivity, perform the following
inspections more frequently than shown on the
Maintenance Schedule;
• check front disc brake pad condition and wear;
• check cleanliness of hood latches, as well as cleanli- ness and lubrication of linkages;
• visually inspect the conditions of: engine, transmis- sion, pipes and tubes (exhaust - fuel - brakes), rubber
parts (boots, sleeves, etc.);
• check battery charge and liquid level (electrolyte);
• visually inspect the condition of auxiliary drive belts;
• check and if necessary change engine oil and oil filter;
• check pollen filter and replace it, if required;
• check air filter and replace, if required;
• check fuel filter and replace, if required.
269
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCYSERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

The A/C air filter is identified with an
arrow to indicate airflow direction
through the filter. Failure to install the
filter properly will result in the need to replace it
more often.
7. Reinstall the glove box door. Make sure that the hinges are seated fully as you raise the door. Other-
wise, the door latch will not align properly.
BODY LUBRICATION
Locks and all body pivot points, including such items as
seat tracks, door hinge pivot points and rollers, liftgate,
tailgate, sliding doors and hood hinges, should be
lubricated periodically with a lithium based grease to
assure quiet, easy operation and to protect against rust
and wear. Prior to the application of any lubricant, the
parts concerned should be wiped clean to remove dust
and grit; after lubricating excess oil and grease should
be removed. Particular attention should also be given
to hood latching components to ensure proper func-
tion. When performing other underhood services, the
hood latch, release mechanism and safety catch should
be cleaned and lubricated.
The external lock cylinders should be lubricated twice
a year, preferably in the Fall and Spring. Apply a small
amount of a high quality lubricant directly into the lock
cylinder. WIPER BLADES
Clean the rubber edges of the wiper blades and the
windshield and rear window periodically with a sponge
or soft cloth and a mild nonabrasive cleaner. This will
remove accumulations of salt, waxes, or road film, and
help reduce streaking and smearing.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always
use washer fluid when using the wipers to remove salt
or dirt from a dry windshield or rear window.
Avoid using the wiper blades to remove frost or ice
from the windshield or rear window. Make sure that
they are not frozen to the glass before turning them on
to avoid damaging the blade. Keep the blade rubber out
of contact with petroleum products such as engine oil,
gasoline, etc.
NOTE:
Life expectancy of wiper blades varies de-
pending on geographical area and frequency of use.
Poor performance of blades may be present with chat-
tering, marks, water lines or wet spots. If any condition
is present please proceed to clean wiper blades with
humid cloth removing any debris that may be affecting
its function.
277
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCYSERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

Rear Wiper Removal/Installation (for
versions/markets, where provided)
1. Lift the pivot cap on the rear wiper arm upward, thiswill allow the rear wiper blade to be raised off of the
liftgate glass. (fig. 181)
NOTE: The rear wiper arm cannot be raised fully
upward unless the pivot cap is raised first.
2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass.
3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the
wiper blade holder. (fig. 182) 4. Install the wiper blade pivot pin into the wiper blade
holder at the end of the wiper arm, and firmly press
the wiper blade until it snaps into place.
5. Lower the wiper blade and snap the pivot cap into place.
ADDING WASHER FLUID
The windshield washer and the rear window washer
share the same fluid reservoir. The fluid reservoir is
located in the engine compartment. Be sure to check
the fluid level in the reservoir at regular intervals. Fill
the reservoir with windshield washer solvent (not
radiator antifreeze) and operate the system for a few
seconds to flush out the residual water.(fig. 181) 1 — Wiper Arm
2 — Pivot Cap
(fig. 182)1 — Wiper Blade
2 — Blade Pivot Pin
3 — Wiper Arm
4 — Wiper Blade Holder
278
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCYSERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

Interior Care
Instrument Panel Cover
The instrument panel cover has a low glare surface,
which minimizes reflections in the windshield. Do not
use protectants or other products, which may cause
undesirable reflections. Use soap and warm water to
restore the low glare surface.
Cleaning Interior Trim
Interior trim should be cleaned starting with a damp
cloth. Do not use harsh cleaners.
Cleaning Leather Upholstery
Your leather upholstery can be best preserved by
regular cleaning with a damp soft cloth. Small particles
of dirt can act as an abrasive and damage the leather
upholstery and should be removed promptly with a
damp cloth. Stubborn soils can be removed easily with
a soft cloth. Care should be taken to avoid soaking your
leather upholstery with any liquid. Please do not use
polishes, oils, cleaning fluids, solvents, detergents, or
ammonia-based cleaners to clean your leather uphol-
stery. Application of a leather conditioner is not re-
quired to maintain the original condition.
WARNING!
Do not use volatile solvents for cleaning
purposes. Many are potentially flam-
mable, and if used in closed areas they may cause
respiratory harm. Cleaning Headlights
Your vehicle has plastic headlights that are lighter and
less susceptible to stone breakage than glass headlights.
Plastic is not as scratch resistant as glass and therefore
different lens cleaning procedures must be followed.
To minimize the possibility of scratching the lenses and
reducing light output, avoid wiping with a dry cloth. To
remove road dirt, wash with a mild soap solution
followed by rinsing.
Do not use abrasive cleaning components, solvents,
steel wool or other aggressive material to clean thelenses.
Glass Surfaces
All glass surfaces should be cleaned on a regular basis
with any commercial household-type glass cleaner.
Never use an abrasive type cleaner. Use caution when
cleaning the inside rear window equipped with an
electric defroster. Do not use scrapers or other sharp
instruments that may scratch the elements.
When cleaning the rear view mirror, spray cleaner on
the towel or rag that you are using. Do not spray
cleaner directly on the mirror.
Cleaning Plastic Instrument Cluster Lenses
The lenses in front of the instruments in this vehicle are
molded in clear plastic. When cleaning the lenses, care
must be taken to avoid scratching the plastic.
289
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCYSERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

TECHNICAL SPECIFICATIONS
VEHICLE IDENTIFICATION NUMBER
The Vehicle Identification Number (VIN) is on the left
front corner of the instrument panel and is visible from
outside of the vehicle through the windshield. This
number also appears stamped on the right front door
sill under the sill moulding and printed on the Automo-
bile Information Disclosure Label affixed to a window
on your vehicle, the vehicle registration and title.
(fig. 183) (fig. 184) TIRES — GENERAL INFORMATION
TIRE PRESSURE
Proper tire inflation pressure is essential to the safe and
satisfactory operation of your vehicle. Three primary
areas are affected by improper tire pressure:
(fig. 183)
VIN Location
(fig. 184)Stamped VIN Location
291
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

(Continued)
 Guard against carbon monoxide with proper
maintenance. Have the exhaust system inspected
every time the vehicle is raised. Have any abnor-
mal conditions repaired promptly. Until re-
paired, drive with all side windows fully open.
 Keep the liftgate closed when driving your ve-
hicle to prevent carbon monoxide and other poi-
sonous exhaust gases from entering the vehicle. FUEL REQUIREMENTS — DIESEL ENGINE
Use Premium Quality Diesel fuels with a Cetane rating
of 50 or higher, and meeting the EN590 standard are
highly recommended. See your authorized dealer for
further information regarding fuels available in your
area.
300
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

CHASSISComponent Fluid, Lubricant, or Genuine Part
Automatic Transmission (for
versions/markets, where provided)TUTELA TRANSMISSION FORCE4 Totally synthetic lubricant that meets FIAT
Classification 9.55550- AV4
Manual Transmission (for
versions/markets, where provided) Grade SAE 75W synthetic lubricant that meets Qualification FIAT
9.55550-MZ6 (TUTELA TRANSMISSION GEARFORCE Contractual Technical
Reference No. F002.F10).
Wheel-Side Constant Velocity Joints Molybdenum disulphide grease, for use at high temperatures. FIAT 9.55580
certification. NL.GI. 1-2 consistency (TUTELA ALL STAR Contractual
Technical Reference No. F702.G07)
Differential-Side Constant Velocity
Joints Grease for constant-velocity joints with low friction coefficient. FIAT 9.55580
certification. NL.GI. 0-2 consistency (TUTELA STAR 700 Contractual Technical
Reference No. F701.C07)
Brake/Clutch Master Cylinder Synthetic fluid, FMVSS no. 116, DOT 4, ISO 4925 SAE J-1704. Qualification
FIAT 9.55597 (TUTELA TOP 4 Contractual Technical Reference No. F001.A93)
Power Steering Reservoir Please refer to your Dealership.
Windshield/Rear Window Washer Fluid Mixture of alcohol, water and surfactants CUNA NC 956-II FIAT 9.55522
certification (TUTELA PROFESSIONAL SC35 Contractual Technical Reference
No. F201.D02)
303
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

CONTENTS
About Your Brakes . . . . . . . . . . . . . . . . . . . . 113,200
ABS (Anti-Lock Brake System) . . . . . . . . . . 113,114,229
Adding Engine Coolant (Antifreeze) . . . . . . . . . 281,282
Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . . 278
Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 299
Air Cleaner, Engine (Engine Air Cleaner Filter) . . . . . 274
Air Conditioner Maintenance . . . . . . . . . . . . . . . . 275
Air Conditioning Filter . . . . . . . . . . . . . . . . . . . 69,276
Air Conditioning Refrigerant . . . . . . . . . . . . . . . . . 275
Air Conditioning System . . . . . . . . . . . . . . . . . 65,275
Air Conditioning, Operating Tips . . . . . . . . . . . . . . . 70
Air Conditioning, Rear Zone . . . . . . . . . . . . . . . . . 66
Air Pressure, Tires . . . . . . . . . . . . . . . . . . . . . 227,292
Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181,188
Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . 189
Airbag Light . . . . . . . . . . . . . . . . . . . 187,190,193,225
Airbag Maintenance . . . . . . . . . . . . . . . . . . . . . . . 190
Airbag, Side . . . . . . . . . . . . . . . . . . . . . . 183,186,188
Airbag, Window (Side Curtain) . . . . . . . . . 184,186,188
Alarm (Security Alarm) . . . . . . . . . . . . . . . . . . 15,230
Alarm System (Security Alarm) . . . . . . . . . . . . . . 15,16
All Wheel Drive (AWD) . . . . . . . . . . . . . . . . . . . 209
Alterations/Modifications, Vehicle . . . . . . . . . . . . . . . 5
Anti-Lock Brake System (ABS) . . . . . . . . . . . . . 113,114
Anti-Lock Warning Light . . . . . . . . . . . . . . 114,115,229
Anti-Theft Security Alarm (Theft Alarm) . . . . . . . . . 15
Anti-Theft System . . . . . . . . . . . . . . . . . . . . . . . . 230
Antifreeze (Engine Coolant) . . . . . . . . . . . 281,282,301 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Appearance Care . . . . . . . . . . . . . . . . . . . . . . . . 287 Arming Theft System (Security Alarm) . . . . . . . . . . . 15
Auto Down Power Windows . . . . . . . . . . . . . . . . 103
Auto Unlock, Doors . . . . . . . . . . . . . . . . . . . . . . . 97
Automatic Dimming Mirror . . . . . . . . . . . . . . . . . . 57
Automatic Door Locks . . . . . . . . . . . . . . . . . . . . . 97
Automatic Headlights . . . . . . . . . . . . . . . . . . . . . . 71
Automatic Oil Change Indicator . . . . . . . . . . . . . . . 23
Automatic Temperature Control (ATC) . . . . . . . . . . 65
Automatic Transaxle . . . . . . . . . . . . . . . . . . . . . . 285
Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Fluid and Filter Changes . . . . . . . . . . . . . . . . . . 286
Selection Of Lubricant . . . . . . . . . . . . . . . . . . . 303
Special Additives . . . . . . . . . . . . . . . . . . . . . . . 285
Automatic Transmission . . . . . . . . . . . . . . . . . . . . 203 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . 286
Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Auxiliary Electrical Outlet (Power Outlet) . . . . . . . . 89
Auxiliary Power Outlet . . . . . . . . . . . . . . . . . . . . . 89
Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 Gas Caution . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Keyless Transmitter Replacement (RKE) . . . . . . . . 13
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . 159,193
Body Mechanism Lubrication . . . . . . . . . . . . . . . . . 277
Booster Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Brake Assist System . . . . . . . . . . . . . . . . . . . . . . . 116
Brake Control System, Electronic . . . . . . . . . . . . . . 114
307
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS