2012 FIAT FREEMONT engine oil

Checking Oil Level – Diesel Engine
To assure proper engine lubrication, the engine oil
must be maintained at the correct level. Check the oil
level at regular intervals, such as every fuel stop.
The best time to check the engine oil level is about five
minutes after a fully warmed engine is shut off or
before starting the engine after it has sat overnight.
Checking the oil while the vehicle is on level ground will
improve the accuracy of the oil level readings. Maintain
the oil level between the MIN and MAX markings on
the dipstick. Adding 1 Liter of oil when the reading is at
the MIN mark will result in a MAX reading on theseengines.
Change Engine Oil – Gasoline Engine
Refer to the “Maintenance Schedule” for the proper
maintenance intervals.
Change Engine Oil – Diesel Engine
Refer to the “Maintenance Schedule” for the proper
maintenance intervals.
Engine Oil Viscosity – 3.6L Gasoline Engine
SAE 5W-30 engine oil is recommended for all operating
temperatures. This engine oil improves low tempera-
ture starting and vehicle fuel economy.The engine oil filler cap also shows the recommended
engine oil viscosity for your vehicle. For information on
engine oil filler cap location, refer to “Engine Compart-
ment” in “Servicing And Care” for further information.
Engine Oil Viscosity – 2.0L Diesel Engine
For best performance and maximum protection under
all types of operating conditions, the manufacturer
recommends Fully Synthetic Low Ash 5W-30 engine
oils that meet the requirements of FIAT 9.55535-S1
spec and ACEA C1/C2.
Materials Added To Engine Oil
Do not add any supplemental materials, other than leak
detection dyes, to the engine oil. Engine oil is an
engineered product and its performance may be im-
paired by supplemental additives.
Disposing Of Used Engine Oil And Oil Filters
Care should be taken in disposing of used engine oil and
oil filters from your vehicle. Used oil and oil filters,
indiscriminately discarded, can present a problem to
the environment. Contact your authorized dealer, ser-
vice station, or governmental agency for advice on how
and where used oil and oil filters can be safely discarded
in your area.
273
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCYSERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

The A/C air filter is identified with an
arrow to indicate airflow direction
through the filter. Failure to install the
filter properly will result in the need to replace it
more often.
7. Reinstall the glove box door. Make sure that the hinges are seated fully as you raise the door. Other-
wise, the door latch will not align properly.
BODY LUBRICATION
Locks and all body pivot points, including such items as
seat tracks, door hinge pivot points and rollers, liftgate,
tailgate, sliding doors and hood hinges, should be
lubricated periodically with a lithium based grease to
assure quiet, easy operation and to protect against rust
and wear. Prior to the application of any lubricant, the
parts concerned should be wiped clean to remove dust
and grit; after lubricating excess oil and grease should
be removed. Particular attention should also be given
to hood latching components to ensure proper func-
tion. When performing other underhood services, the
hood latch, release mechanism and safety catch should
be cleaned and lubricated.
The external lock cylinders should be lubricated twice
a year, preferably in the Fall and Spring. Apply a small
amount of a high quality lubricant directly into the lock
cylinder. WIPER BLADES
Clean the rubber edges of the wiper blades and the
windshield and rear window periodically with a sponge
or soft cloth and a mild nonabrasive cleaner. This will
remove accumulations of salt, waxes, or road film, and
help reduce streaking and smearing.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always
use washer fluid when using the wipers to remove salt
or dirt from a dry windshield or rear window.
Avoid using the wiper blades to remove frost or ice
from the windshield or rear window. Make sure that
they are not frozen to the glass before turning them on
to avoid damaging the blade. Keep the blade rubber out
of contact with petroleum products such as engine oil,
gasoline, etc.
NOTE:
Life expectancy of wiper blades varies de-
pending on geographical area and frequency of use.
Poor performance of blades may be present with chat-
tering, marks, water lines or wet spots. If any condition
is present please proceed to clean wiper blades with
humid cloth removing any debris that may be affecting
its function.
277
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCYSERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

When refilling the washer fluid reservoir, apply some
washer fluid to a cloth or towel and wipe the wiper
blades clean. This will help blade performance.
To prevent freeze-up of your windshield washer system
in cold weather, select a solution or mixture that meets
or exceeds the temperature range of your climate. This
rating information can be found on most washer fluid
containers.
The fluid reservoir will hold nearly 4 Liters of washer
fluid when the “Washer Fluid Low” message appears in
the EVIC display.
WARNING!
Commercially available windshield
washer solvents are flammable. They
could ignite and burn you. Care must be exer-
cised when filling or working around the washer
solution.
INTERVENTION REGENERATION
STRATEGY – 2.0L DIESEL ENGINE
This vehicle is equipped with a state-of-the-art engine
and exhaust system containing a diesel particulate
filter. The engine and exhaust after-treatment system
work together to meet the Emission standards. The
system manages engine combustion to allow the ex-
haust system’s catalyst to trap and burn Particulate
Matter (PM) pollutants with no input or interaction on
your part. Refer to “Electronic Vehicle Information Center
(EVIC)” in “Knowing Your Vehicle” for further
information.
EXHAUST SYSTEM
The best protection against carbon monoxide entry
into the vehicle body is a properly maintained engine
exhaust system.
Whenever a change is noticed in the sound of the
exhaust system, when exhaust fumes can be detected
inside the vehicle, or when the underside or rear of the
vehicle is damaged, have a competent technician in-
spect the complete exhaust system and adjacent body
areas for broken, damaged, deteriorated, or misposi-
tioned parts. Open seams or loose connections could
permit exhaust fumes to seep into the passenger com-
partment. In addition, inspect the exhaust system each
time the vehicle is raised for lubrication or oil change.
Replace as required.
WARNING!
Exhaust gases can injure or kill. They
contain carbon monoxide (CO), which is
colorless and odorless. Breathing it can make you
unconscious and can eventually poison you. To
avoid breathing CO, refer to “Safety Tips/Exhaust
Gas” in “Safety” for further information.
279
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCYSERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

NOTE:Intentional tampering with emissions control
systems can result in civil penalties being assessed
against you.
WARNING!
A hot exhaust system can start a fire if
you park over materials that can burn.
Such materials might be grass or leaves coming
into contact with your exhaust system. Do not
park or operate your vehicle in areas where your
exhaust system can contact anything that canburn.
In unusual situations involving grossly malfunctioning
engine operation, a scorching odor may indicate severe
and abnormal catalyst overheating. If this occurs, safely
bring the vehicle to a complete stop, shut the engine
OFF, and allow the vehicle to cool. Thereafter, obtain
service, including a tune-up to manufacturer's specifi-
cations immediately.
To minimize the possibility of catalyst damage:
• Do not shut OFF the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion.
• Do not try to start the engine by pushing or towing the vehicle.
• Do not idle the engine with any ignition coil connec- tors disconnected for prolonged periods. COOLING SYSTEM
WARNING!
 When working near the radiator cool-
ing fan, disconnect the fan motor lead or
turn the ignition switch to the LOCK position.The
fan is temperature controlled and can start at
any time the ignition switch is in the ON position.
 You or others can be badly burned by hot
coolant or steam from your radiator. If you see or
hear steam coming from under the hood, do not
open the hood until the radiator has had time to
cool. Never try to open a cooling system pressure
cap when the radiator is hot .
Coolant Checks
Check engine coolant (antifreeze) protection every
12 months (before the onset of freezing weather,
where applicable). If coolant is dirty or rusty in appear-
ance, the system should be drained, flushed, and re-
filled with fresh coolant. Check the front of the A/C
condenser for any accumulation of bugs, leaves, etc. If
dirty, clean by gently spraying water from a garden hose
vertically down the face of the condenser.
Check the coolant recovery bottle tubing for brittle
rubber, cracking, tears, cuts, and tightness of the con-
nection at the bottle and radiator. Inspect the entire
system for leaks.
280
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCYSERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

(Continued)
 To avoid contamination from foreign matter or
moisture, use only new brake fluid or fluid that
has been in a tightly closed container. Keep the
master cylinder reservoir cap secured at all
times. Brake fluid in a open container absorbs
moisture from the air resulting in a lower boiling
point . This may cause it to boil unexpectedly
during hard or prolonged braking, resulting in
sudden brake failure. This could result in a acci-
dent .
 Overfilling the brake fluid reservoir can result
in spilling brake fluid on hot engine parts, causing
the brake fluid to catch fire. Brake fluid can also
damage painted and vinyl surfaces, care should
be taken to avoid its contact with these surfaces.
 Do not allow petroleum based fluid to con-
taminate the brake fluid. Brake seal components
could be damaged, causing partial or complete
brake failure.This could result in an accident .
AUTOMATIC TRANSMISSION (for
versions/markets, where provided)
The automatic transmission and differential assembly
are contained within a single housing.
The fluid level in the automatic transmission should be
checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life
of the transmission and the fluid.
Selection Of Lubricant
It is important that the proper lubricant is used in the
transmission to assure optimum transmission perfor-
mance. Use only manufacturer’s recommended trans-
mission fluid. Refer to “Fluids, Lubricants, and Genuine
Parts” in “Technical Specifications” for further informa-
tion. It is important that the transmission fluid be
maintained at the prescribed level using the recom-
mended fluid. No chemical flushes should be used in
any transmission; only the approved lubricant may beused.
Special Additives
Automatic Transmission Fluid (ATF) is an engineered
product and its performance may be impaired by
supplemental additives. Therefore, do not add any fluid
additives to the transmission. The only exception to
this policy is the use of special dyes to aid in detecting
fluid leaks. In addition, avoid using transmission sealers
as they may adversely affect seals.
Do not use chemical flushes in your
transmission as the chemicals can dam-
age your transmission components. Such
damage is not covered by the New Vehicle Limited
Warranty.
285
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCYSERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

FLUID CAPACITIES
Metric
Fuel (Approximate) 77.6 Liters
Engine Oil with Filter
3.6L Engine 5.6 Liters
2.0L Diesel Engine 5.2 Liters
Cooling System *
3.6L Engine and Single- or Dual-Zone Climate Control System 12.4 Liters
3.6L Engine and Three-Zone Climate Control System 13.7 Liters
2.0L Diesel Engine and Single- or Dual-Zone Climate Control System 9.1 Liters
2.0L Diesel Engine and Three-Zone Climate Control System 9.9 Liters
* Includes heater and coolant recovery bottle filled to MAX level.
301
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

FLUIDS, LUBRICANTS, AND GENUINE PARTS ENGINEComponent Fluids, Lubricants, and Genuine Parts
Engine Coolant50% mixture of demineralized water and PARAFLU UP* that meets FIAT
Qualification 9.55523 Antifreeze/Coolant or equivalent.
Engine Oil – 3.6L Engine SAE Grade 5W-30 SELENIA K POWER fully synthetic engine oil that meets
FIAT Qualification 9.55535 API SN, ILSAC GF-5 or equivalent.
Engine Oil – 2.0L Diesel Engine SAE Grade 5W-30 SELENIA WR P.E fully synthetic engine oil that meets FIAT
Qualification 9.55535–S1 or equivalent.
Spark Plugs – 3.6L Engine RER8ZWYCB4 (Gap 1.1 mm)
Fuel Selection – 3.6L Engine 91 Octane
Fuel Selection – 2.0L Diesel Engine 50 Cetane or higher (Less than 15 ppm Sulfur).
302
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

CONTENTS
About Your Brakes . . . . . . . . . . . . . . . . . . . . 113,200
ABS (Anti-Lock Brake System) . . . . . . . . . . 113,114,229
Adding Engine Coolant (Antifreeze) . . . . . . . . . 281,282
Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . . 278
Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 299
Air Cleaner, Engine (Engine Air Cleaner Filter) . . . . . 274
Air Conditioner Maintenance . . . . . . . . . . . . . . . . 275
Air Conditioning Filter . . . . . . . . . . . . . . . . . . . 69,276
Air Conditioning Refrigerant . . . . . . . . . . . . . . . . . 275
Air Conditioning System . . . . . . . . . . . . . . . . . 65,275
Air Conditioning, Operating Tips . . . . . . . . . . . . . . . 70
Air Conditioning, Rear Zone . . . . . . . . . . . . . . . . . 66
Air Pressure, Tires . . . . . . . . . . . . . . . . . . . . . 227,292
Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181,188
Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . 189
Airbag Light . . . . . . . . . . . . . . . . . . . 187,190,193,225
Airbag Maintenance . . . . . . . . . . . . . . . . . . . . . . . 190
Airbag, Side . . . . . . . . . . . . . . . . . . . . . . 183,186,188
Airbag, Window (Side Curtain) . . . . . . . . . 184,186,188
Alarm (Security Alarm) . . . . . . . . . . . . . . . . . . 15,230
Alarm System (Security Alarm) . . . . . . . . . . . . . . 15,16
All Wheel Drive (AWD) . . . . . . . . . . . . . . . . . . . 209
Alterations/Modifications, Vehicle . . . . . . . . . . . . . . . 5
Anti-Lock Brake System (ABS) . . . . . . . . . . . . . 113,114
Anti-Lock Warning Light . . . . . . . . . . . . . . 114,115,229
Anti-Theft Security Alarm (Theft Alarm) . . . . . . . . . 15
Anti-Theft System . . . . . . . . . . . . . . . . . . . . . . . . 230
Antifreeze (Engine Coolant) . . . . . . . . . . . 281,282,301 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Appearance Care . . . . . . . . . . . . . . . . . . . . . . . . 287 Arming Theft System (Security Alarm) . . . . . . . . . . . 15
Auto Down Power Windows . . . . . . . . . . . . . . . . 103
Auto Unlock, Doors . . . . . . . . . . . . . . . . . . . . . . . 97
Automatic Dimming Mirror . . . . . . . . . . . . . . . . . . 57
Automatic Door Locks . . . . . . . . . . . . . . . . . . . . . 97
Automatic Headlights . . . . . . . . . . . . . . . . . . . . . . 71
Automatic Oil Change Indicator . . . . . . . . . . . . . . . 23
Automatic Temperature Control (ATC) . . . . . . . . . . 65
Automatic Transaxle . . . . . . . . . . . . . . . . . . . . . . 285
Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Fluid and Filter Changes . . . . . . . . . . . . . . . . . . 286
Selection Of Lubricant . . . . . . . . . . . . . . . . . . . 303
Special Additives . . . . . . . . . . . . . . . . . . . . . . . 285
Automatic Transmission . . . . . . . . . . . . . . . . . . . . 203 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . 286
Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Auxiliary Electrical Outlet (Power Outlet) . . . . . . . . 89
Auxiliary Power Outlet . . . . . . . . . . . . . . . . . . . . . 89
Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 Gas Caution . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Keyless Transmitter Replacement (RKE) . . . . . . . . 13
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . 159,193
Body Mechanism Lubrication . . . . . . . . . . . . . . . . . 277
Booster Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Brake Assist System . . . . . . . . . . . . . . . . . . . . . . . 116
Brake Control System, Electronic . . . . . . . . . . . . . . 114
307
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS