Page 169 of 506

NOTE:HomeLink is disabled when the Vehicle Secu-
rity Alarm is active.
Before You Begin Programming HomeLink
Be sure that your vehicle is parked outside of the garage
before you begin programming. For more efficient programming and accurate transmis-
sion of the radio-frequency signal it is recommended that
a new battery be placed in the hand-held transmitter of
the device that is being programmed to the HomeLink
system.
Erase all channels before you begin programming. To
erase the channels place the ignition in the ON/RUN
position and press and hold the two outside HomeLink
buttons (I and III) for up 20 seconds or until the red
indicator flashes.
NOTE:
•Erasing all channels should only be performed when
programming HomeLink for the first time. Do not
erase channels when programming additional buttons.
•If you have any problems, or require assistance, please
call toll-free 1–800–355–3515 or, on the Internet at
www.HomeLink.com for information or assistance.
HomeLink Buttons/Sunvisor/Headliner
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167
Page 173 of 506

Reprogramming A Single HomeLinkButton
To reprogram a channel that has been previously trained,
follow these steps:
1. Turn the ignition switch to the ON/RUN position.
2. Press and hold the desired HomeLink button until
the indicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button proceed with “Program-
ming A Non-Rolling Code” Step 2 and follow all remain-
ing steps.
Canadian/Gate Operator Programming
For programming transmitters in Canada/United States
that require the transmitter signals to “time-out” after
several seconds of transmission.
Canadian radio frequency laws require transmitter sig-
nals to time-out (or quit) after several seconds of trans-
mission – which may not be long enough for HomeLink to pick up the signal during programming. Similar to this
Canadian law, some U.S. gate operators are designed to
time-out in the same manner.
It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the garage
door or gate motor.
1. Turn the ignition switch to the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)
away from the HomeLink
button you wish to program
while keeping the HomeLink indicator light in view.
3. Continue to press and hold the HomeLink button,
while you press and release (“cycle”), your hand-held
transmitter every two seconds until HomeLink has
successfully accepted the frequency signal. The indicator
light will flash slowly and then rapidly when fully
trained.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171
Page 197 of 506
UNDERSTANDING YOUR INSTRUMENT PANEL
CONTENTS
Instrument Panel Features ............... 198
Instrument Cluster — Base ............... 199
Instrument Cluster — Premium ........... 200
Instrument Cluster Descriptions ........... 201
Electronic Vehicle Information Center (EVIC) —
If Equipped .......................... 215
▫ Oil Change Required — If Equipped ...... 217
▫ EVIC Functions ..................... 218
▫ Compass/Temperature/Audio ........... 218▫
Average Fuel Economy ................ 219
▫ Distance To Empty (DTE) .............. 219
▫ Elapsed Time ....................... 219
▫ Tire Pressure Monitor (TPM) ............ 219
▫ Personal Settings (Customer-Programmable
Features) .......................... 220
Media Center 230 (REQ) — AM/FM Stereo
Radio And 6–Disc CD/DVD Changer
(MP3/WMA AUX Jack) .................. 225
▫ Operating Instructions - Radio Mode ...... 226
4
Page 198 of 506

▫Operation Instructions - (Disc Mode For CD
And MP3/WMA Audio Play, DVD-Video) . . . 234
▫ Notes On Playing MP3/WMA Files ....... 236
▫ List Button (Disc Mode For MP3/
WMA Play) ........................ 238
▫ Info Button (Disc Mode For MP3/WMA
Play) ............................. 239
▫ Uconnect™ Multimedia (Satellite Radio) — If
Equipped .......................... 241
Media Center 730N/430/430N (RHR/RER/
RBZ/RHB) CD/DVD/HDD/NAV — If
Equipped ............................ 245
▫ Operating Instructions (Voice Command
System) — If Equipped ................ 245
▫ Operating Instructions (Uconnect™ Phone)
— If Equipped ...................... 245
Media Center 130 (Sales Code RES) ......... 246
▫ Operating Instructions — Radio Mode ..... 246
▫ Operation Instructions — CD Mode For CD
And MP3 Audio Play ................. 249
▫ Notes On Playing MP3 Files ............ 251
▫ Operation Instructions - Auxiliary Mode .... 254
Media Center 130 With Satellite Radio (Sales
Code RES+RSC) ....................... 254
▫ Operating Instructions — Radio Mode ..... 255
▫ Operation Instructions — CD Mode For CD
And MP3 Audio Play ................. 260
▫ Notes On Playing MP3 Files ............ 262
▫ List Button (CD Mode For MP3 Play) ...... 265
▫ Info Button (CD Mode For MP3 Play) ...... 265
196 UNDERSTANDING YOUR INSTRUMENT PANEL
Page 199 of 506
▫Uconnect™ Multimedia (Satellite Radio) — If
Equipped .......................... 266
iPod/USB/MP3 Control — If Equipped ..... 270
▫ Connecting The iPod Or External USB
Device ............................ 271
▫ Using This Feature ................... 272
▫ Controlling The iPod Or External USB
Device Using Radio Buttons ............. 272
▫ Play Mode ......................... 272
▫ List Or Browse Mode ................. 274
▫ Bluetooth Streaming Audio (BTSA) ........ 276
Steering Wheel Audio Controls —
If Equipped .......................... 277 ▫
Radio Operation ..................... 278
▫ CD Player ......................... 278
CD/DVD Disc Maintenance .............. 279
Radio Operation And Mobile Phones ....... 279
Climate Controls ...................... 280
▫ Manual Heating And Air Conditioning ..... 280
▫ Automatic Temperature Control (ATC) — If
Equipped .......................... 284
▫ Operating Tips ...................... 290
4
UNDERSTANDING YOUR INSTRUMENT PANEL 197
Page 200 of 506
INSTRUMENT PANEL FEATURES
1 — Air Outlet5 — Lower Glove Compartment/Beverage Cooler –
If Equipped 9 — ESC OFF Switch – If Equipped
2 — Instrument Cluster 6 — Climate Controls 10 — Storage Bins
3 — Radio 7 — Heated Seat Switches – If Equipped 11 — Power Outlet
4 — Passenger Airbag 8 — Hazard Warning Flasher
198 UNDERSTANDING YOUR INSTRUMENT PANEL
Page 220 of 506
NOTE:If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary, repeat this procedure.
EVIC Functions
Press the EVIC button until one of the following func-
tions are displayed on the EVIC:
•Compass/Temperature/Audio
•Average Fuel Economy
•Distance To Empty (DTE)
•Elapsed Time
•Tire Pressure Monitor (TPM)
•Personal Settings
To Reset The Display
Pressing and holding the EVIC button once will clear the
function currently being displayed. Reset will only occur
if a resettable function is currently being displayed.
Compass/Temperature/Audio
Press and release the EVIC button to display one of eight
compass headings to indicate the direction the vehicle is
facing, the outside temperature, and the current radio
station.
EVIC Button
218 UNDERSTANDING YOUR INSTRUMENT PANEL
Page 223 of 506

RKE Unlock
When Driver Dr. 1st Press is selected only the driver’s
door will unlock on the first press of the Remote Keyless
Entry (RKE) transmitter UNLOCK button and require a
second press to unlock the remaining locked doors.
When All Doors 1st Press is selected, all of the doors will
unlock at the first press of the RKE transmitter UNLOCK
button. Press and hold the EVIC button when in this
display until “All Doors 1st Press” appears to make your
selection.
Sound Horn with Lock
When ON is selected, a short horn sound will occur when
the RKE transmitter LOCK button is pressed. This feature
may be selected with or without the Flash Lamps feature.
Press and hold the EVIC button when in this display until
“ON” or “OFF” appears to make your selection.
Flash Lamps Lock
When ON is selected, the front and rear turn signals will
flash when the doors are locked or unlocked using the
RKE transmitter. This feature may be selected with or
without the Sound Horn with Lock feature selected. Press
and hold the EVIC button when in this display until
“ON” or “OFF” appears to make your selection.
Headlamp Off Delay
When this feature is selected, the driver can choose to
have the headlights remain on for 0, 30, 60, or 90 seconds
when exiting the vehicle. Press and hold the EVIC button
when in this display until 0, 30, 60, or 90 appears to make
your selection.
Key-Off Power Delay
When this feature is selected, the power window
switches, radio, Uconnect™ phone, power sunroof, and
power outlets will remain active for up to 10 minutes
after the ignition switch has been turned off. Opening
4
UNDERSTANDING YOUR INSTRUMENT PANEL 221