2012 Citroen DS4 bulb

CHECKS PRACTICAL
INFORMATIONTECHNICAL DATA AUDIO AND
TELEMATICS
233 Bonnet
234Running out of fuel (Diesel)
235Petrol engines
236 Diesel engines
237 Checking levels
240 Checks
246Te m p o r a ry puncture repair
kit
251 Changing a wheel
258 Changing a bulb
265Changing a fuse
271 12 V battery
274 Energy economy mode
275Changing a wiper blade
275Very cold climate screen
276Fitting roof bars
277 Towing the vehicle
279To w i ng a trailer
281 Accessories
286 Petrol engines
287 Petrol weights
288Diesel engines
289Diesel weights
290Dimensions
291Identifi cation markings
295 Emergency or assistance
297 eMyWay
349 Audio system
012012013013010010011011

Automatic adjustment of xenon headlamps
Do not touch the xenon bulbs. Contact a CITROËN dealer or a
qualified workshop. This s
ystem adjusts the height of the xenon
headlamp beams automatically and when
stationary, according to the load in the vehicle, so
as to avoid causing a nuisance to other road user.
I
f a malfunction occurs, this
warning lamp is displayed in the
instrument panel, accompanied byan audible signal and a message in the screen.
The system then places your headlamps in the lowest position.







Manual adjustment
of halogen
headlamps
To avoid causing a nuisance to other road
users, the height of the halogen headlampsshould be adjusted according to the load in the
vehicle.0.1 or 2 people in the front seats. -.3 people.1. 5 people.-.Intermediate setting. 2.
5 people + maximum authorised load. -.Intermediate setting. 3.
Driver + maximum authorised load.
The initial setting is position "0".

Use
)Extract the torch from its location pulling it upwards.)Press the switch, located on the back,
to switch the torch on or off. )Unfold the suppor t, located on the back,
to set down and raise the torch; for
example, when changing a wheel.



Storing
)
Put the torch back in place in its locationstarting with the lower part.
If you have forgotten to switch off the torch,
this switches it off automatically.
Storage box
)Raise the boot carpet for access to
the storage box.
This has areas for the storage a box of spare
bulbs, a first aid kit, two warning triangles...
It also contains the vehicle tools, the temporarypuncture repair kit...
It the torch is not engaged correctly, it may not charge and may not come onwhen the boot is opened.

Changing a bulb

The headlamps are fitted withpolycarbonate glass with a protectivecoating:)do not clean them using a dryor abrasive cloth, nor with adetergent or solvent product,)use a sponge and soapy water, )when using a high pressurewasher on persistent marks, do not keep the lance directed towards the lamps or their edges for too long, so as not to damage their protective coating and seals.
)Do not touch the bulb directly withyour fingers, use lint-free cloths.Changing a bulb should only be doneafter the headlamp has been switched off for a few minutes (risk of seriousburns).It is imperative to use onlyanti-ultraviolet (UV) type bulbs in order not to damage the headlamp.
Always replace a failed bulb with anew bulb with the same type and specification.


Risk of electrocution

Xenon bulbs (D1S-35W) must be replaced by a CITROËN dealer or aqualified workshop.


Bulbs with lugs, type H1, H7... take careto position them correctly to ensure thebest lighting.

Practical information
Model with xenon and directional
headlamps
1.Directional dipped/main beam
headlamps
(D1S-35W).2. Direction indicators (PY21W amber).3.Daytime running lamps (P21/5W XL).4.Sidelamps (LEDs).5.Foglamps (H11- 55W).
Model with halogen headlamps
1.Direction indicators (H21 clear).2.Dipped beam headlamps (H7-55W).
3.Main beam headlamps (H1- 55W).4. Daytime running lamps (P21/5W XL).5.Sidelamps (LEDs).6.Foglamps (H11- 55W).


Access to bulbs

Depending on the engine and only on the left
hand side, you must first carry out the following operations for access to the protective covers on the bulbs.) Remove the air deflector by unclipping each of its three attachment points.)
Unclip the bonnet release cable at its two
fixings. ) Move the cable down.
After changing the failed bulb, remember to
put everything back in place (cable and air
de
flector).

Front lamps

Changing dipped beam headlamp
bulbs (only on models with
halogen headlamps)
)Remove the protective cover by pulling on
the tab. )Disconnect the bulb connector. )Spread the springs to release the bulb.)Extract the bulb and change it.
To reassemble, carry out these operations in
r
everse order.
Changing direction indicator
bulbs
When refitting, close the protectivecover carefully to preser ve the sealing
of the headlamp.


Amber coloured bulbs, such as thedirection indicators, must be replacedwith bulbs of identical specificationsand colour.

Rapid flashing of the direction indicator warning lamp (right or left) indicates thefailure of a bulb on that side.
Model with Xenon headlamps)
Remove the protective cover by pulling on
its tongue. ) Disconnect the electrical connector. )
Separate the springs to release the bulb.)
Pull the bulb out and replace it.
To r e a s s e m b l e , c a r ry out these operations in reverse order.Model with halogen headlamps)Turn the bulb holder a quarter of a turn and extract it. )Pull out the bulb and change it.
To reassemble, carry out these operations inreverse order.

Practical information
Changing daytime running lamp bulbs
) Remove the protective cover by pulling on
the tab.) Disconnect the bulb connector. )
Turn the bulb holder a quar ter of a turn and extract it.)
Pull the bulb and change it.
To reassemble, carry out these operations in
reverse order.

Changing main beam headlamp
bulbs (only on models with
halogen headlamps)
)Remove the protective cover by pulling on
the tab. )Disconnect the bulb connector. )Squeeze the springs to release the bulb. )Pull out the bulb and replace it.
To reassemble, carry out these operations in
reverse order.

Changing integrated directionindicator side repeaters
)
Insert a screwdriver towards the centre of
the repeater between the repeater and the
base of the mirror. ) Tilt the screwdriver to extract the repeater and remove it. )
Disconnect the repeater connector.
To reassemble, carry out these operations in
r
everse order.
Contact a CITROËN dealer or a qualified
workshop to obtain replacement repeaters.

Changing the side spotlamps
For the replacement of this type of LED lamp,contact a CITROËN dealer or a qualified
workshop.


Changing the LED lamps/sidelamps

For the replacement of this type of LED lamp, contact a CITROËN dealer or a qualified
workshop.
Changing foglamp bulbs
)Introduce a flat screwdriver in the hole in
the finisher. )Pull and lever to unclip the bumper finisher (the parking sensor stays with the finisher).)Remove the two module fixing screws and remove it from its housing. )Disconnect the bulb holder connector. )Turn the bulb holder a quarter of a turn andextract it. )Pull the bulb and change it.
To r e f i t , c a r ry out these operations in reverse order.
To replace these bulbs you may also contact a
CITROËN dealer or a qualified workshop.