2012 Citroen C5 RHD ignition

X
!
173
CHECKS

Screenwash and headlamp
wash fluid

Fluid specifi cation
For optimum cleaning and to avoid
freezing, this fl uid must not be topped
up or replaced with plain water.
Reservoir capacities:


-
screenwash: approximately 3.5 litres,


- screenwash and headlamp wash:
approximately 6.15 litres.












Diesel additive level
(Diesel engine with particle
emission filter)

Topping up
This additive must be topped up by
a CITROËN dealer or a qualifi ed
workshop without delay.











Used products

Avoid prolonged contact of
used oil or fl uids with the
skin.
Most of these fl uids are harmful to
health or indeed very corrosive.
Do not discard used oil or
fl uids into sewers or onto the
ground.
Take used oil to a CITROËN dealer
or a qualifi ed workshop (France) or
to an authorised waste disposal
site. In the case of vehicles fi tted
with headlamp washers, the
minimum level of this fl uid
is indicated by an audible
signal and a message in the multi-
function screen.
Top up the level when you stop the
vehicle.

Coolant level


Coolant change
The coolant does not have to be
changed.

Fluid specifi cation
The coolant must conform to the
manufacturer's recommendations.
The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm,
the temperature of the coolant is
regulated by the fan. This can oper-
ate with the ignition off.

On vehicles which are fi tted with
a particle emission fi lter, the fan
may operate after the vehicle has
been switched off, even if the en-
gine is cold.

In addition, as the cooling system is
pressurised, wait at least one hour
after switching off the engine before
carrying out any work.
To avoid any risk of scalding, un-
screw the cap by two turns to
allow the pressure to drop. When
the pressure has dropped, remove
the cap and top up the level. The additive reservoir
low level is indicated
by fi xed illumination
of this warning lamp,
accompanied by an audible warning
and a message in the multifunction
screen.

XI
176
PRACTICAL INFORMATION











TEMPORARY PUNCTURE
REPAIR KIT
Using the kit

The kit is located in the boot under
the fl oor.

)
Switch off the ignition.

)
Affi x the speed limitation sticker
to the vehicle's steering wheel
to remind you that a wheel is in
temporary use.

)
Check that the switch A
is in
position "0"
.

)
Connect the pipe of the car-
tridge 1
to the valve of the tyre to
be repaired.

)
Connect the compressor's elec-
tric plug to the vehicle's 12 V
socket.

)
Start the vehicle and leave the
engine running. Complete system consisting of a
compressor and a sealant cartridge
which permits the temporary repair

of the tyre so that you can drive to
the nearest garage.
This repair kit is available from
CITROËN dealers or a qualifi ed
workshop.
It is designed to repair holes of a
maximum diameter of 6 mm, locat-
ed exclusively on the tyre tread or
shoulder. Avoid removing any for-
eign bodies which have penetrated
the tyre.

XI
!
181
PRACTICAL INFORMATION












Removing a wheel



)
Park the vehicle on stable, fi rm
ground that is not slippery. apply
the parking brake.

)
If your vehicle is equipped with
"Hydractive III+" suspension, with
the engine running at idle, adjust
the ground clearance to its maxi-
mum height.

)
Switch off the ignition and en-
gage fi rst gear or reverse gear
depending on any slope (for a
vehicle with automatic gearbox,
select position P
).

)
If your vehicle is fi tted with
"Hydractive III+" suspension, po-
sition the chock, whichever direc-
tion the gradient may be in, in front
of the front wheel diametrically op-
posite to the one to be replaced.
)
Position the jack at one of the four
jacking-points provided on the un-
derbody close to the wheels, then
use the wheelbrace to unwind the
jack until it reaches the ground.

)
Remove the protector from each
bolt using tool 3
.

)
Slacken the wheel bolts.

Before positioning the
jack:



)
Always adjust the vehicle’s
ground clearance to the "maxi-
mum height" position and re-
tain this adjustment for as long
as the jack is under the vehicle
(do not use the hydraulic ad-
justments),

)
Immobilise your vehicle on hor-
izontal, stable and non-slippery
ground,

)
Ensure that any passengers
have left the vehicle and are in
a safe place .


Never get underneath the vehicle if
it is supported only by the jack.
The jack and all of the tools are
specifi c to your vehicle. Do not use
them for any other applications.
Have the original wheel repaired
and refi tted as soon as possible.
)
Continue to extend the jack until
the wheel is a few centimetres
off the ground.

)
Undo the bolts, remove the wheel.

XI
195
PRACTICAL INFORMATION
FUSEBOX C



Fuse N°



Rating



Function




F1



15 A

Rear screen wipe (Tourer)


F2



30 A

Locking and deadlocking relay


F3



5 A

Airbags


F4



10 A

Automatic gearbox - additional heater unit (Diesel) -
electrochrome rear view mirror


F5



30 A

Front window - sunroof - passenger door lighting -
passenger door mirror adjustment


F6



30 A

Rear window


F7



5 A

Vanity mirror lighting - Glove box lighting - interior lamps -
torch (tourer)


F8



20 A

Radio - CD changer - Steering mounted controls - Screen - Under-infl ation detection -
Electric boot ECU


F9



30 A

Cigar lighter - front 12 V socket


F10



15 A

Alarm - Steering mounted controls, signalling and wiper controls


F11



15 A

Low current ignition switch


F12



15 A

Driver’s electric seat - instrument panel - seat belt not fastened warning lamps -
air conditioning controls


F13



5 A

Engine relay unit - Hydraulic suspension pump cut-off relay -
airbag ECU supply


F14



15 A

Rain and sunshine sensor - parking sensors - passenger’s electric seat -
trailer relay unit - HIFI amplifi er ECU - Bluetooth system -
Lane Departure Warning System


F15



30 A

Locking and deadlocking relay


F17



40 A

Heated rear screen - heated door mirrors


FSH



SHUNT

PARK SHUNT

XI
196
PRACTICAL INFORMATION

Fuses under the bonnet


After a repair, carefully refi t the
cover.


Any repairs on the MAXI fuses
(that give additional protection),
located in the fuseboxes, must
be left to a CITROËN dealer or a
qualifi ed workshop.

Access to the fuses


)
Undo each screw by a 1/4 turn.

)
Replace the fuse.

Table of fuses



Fuse N°



Rating



Function




F1



20 A

Engine control unit


F2



15 A

Horn


F3



10 A

Screen wash pump


F4



10 A

Headlamp wash pump


F5



15 A

Starter


F6



10 A

Airfl ow sensor - Directional headlamps -
Diagnostic socket


F7



10 A

Automatic gear lever lock -
Power steering


F8



25 A

Starter motor


F9



10 A

Clutch switch - Stop switch


F10



30 A

Actuator motors


F11



40 A

Air conditioning blower


F12



30 A

Wipers


F13



40 A

BSI supply (ignition on)


F14



30 A

-


F15



10 A

Right-hand main beam


F16



10 A

Left-hand main beam


F17



15 A

Right-hand dipped beam


F18



15 A

Left-hand dipped beam


F19



15 A

Actuator motors


F20



10 A

Actuator motors


F21



5 A

Actuator motors

XI
!
199
PRACTICAL INFORMATION

Starting using another
battery


)
Lift the pins to remove the front
left headlamp cover (V6 HDi en-
gine).

)
Connect the red cable to the
positive terminal (+) of the fl at
battery A
, then to the positive ter-
minal (+) of the slave battery B
.

)
Connect one end of the green or
black cable to the negative ter-
minal (-) of the slave battery B
.
V6 HDi engine: the positive ter-
minal (-) is located under the red
cover.

)
Connect the other end of the
green or black cable to the earth
point C
on the broken down ve-
hicle.

)
Operate the starter, let the en-
gine run.

)
Wait until the engine returns to
idle and disconnect the cables.



Charging the battery using a
battery charger
The batteries contain harmful
substances such as sulphuric
acid and lead. They must be
disposed of in accordance
with regulations and must not, in
any circumstances, be discarded
with household waste.
Take used remote control batteries
and vehicle batteries to an autho-
rised collection point.
It is advisable to disconnect the
battery if the vehicle is to be left un-
used for more than one month. Do not disconnect the terminals
while the engine is running.
Do not charge the batteries without
disconnecting the terminals fi rst.
Do not touch the clips during the
operation.
Do not lean over the batteries.
Disconnect the cables in the re-
verse order to connection, ensur-
ing that they do not touch.

Before disconnecting the
battery
Wait 2 minutes after switching off
the ignition before disconnecting
the battery.
Close the windows and the doors
before disconnecting the battery.

Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit
initialisation of the electronic sys-
tems. However, if slight malfunctions
remain following this operation, con-
tact a CITROËN dealer or a qualifi ed
workshop.
Referring to the corresponding sec-
tion, you must yourself reinitialise:


- the remote control key,

- the glass panoramic roof blind,

- the GPS satellite navigation
system.



)
Disconnect the battery from the
vehicle.

)
Follow the instructions for use
provided by the manufacturer of
the charger.

)
Reconnect starting with the neg-
ative terminal (-).

)
Check that the terminals and
connectors are clean. If they are
covered with sulphate (whitish or
greenish deposit), remove them
and clean them.


The Stop & Start battery does not
have to be disconnected for charging.

226








EMERGENCY OR ASSISTANCE CALL


EMERGENCY CALL


In an emergency, press this button for more than
2 seconds. Flashing of the green indicator lamp and a
voice message confi rm that the call has been made to the
CITROËN Emergency team * .

Pressing this button again immediately cancels the request. The green
indicator lamp goes off.


ASSISTANCE CALL


When the ignition is switched on, the green
indicator lamp comes on for 3 seconds
indicating that the system is operating
correctly.

If the orange indicator lamp fl ashes: there is a
system fault.
If the orange indicator lamp is on continuously:
the backup battery must be replaced.
In either case, contact a CITROËN dealer or a
qualifi ed workshop.
Pressing this button again immediately cancels the request.
The cancellation is confi rmed by a voice message.

Press this button for more than 2 seconds to request
assistance if the vehicle breaks down.
A voice message confi rms that the call has been made * .


OPERATION OF THE SYSTEM


The green indicator lamp remains on (without fl ashing) when
communication is established. It goes off at the end of communication.

This call is dealt with by the CITROËN Emergency team which receives
locating information from the vehicle and can send a detailed alert to the
appropriate emergency services. In countries in which the team is not
operational, or when the locating service has been expressly declined,
the call is dealt with directly by the emergency services (112) without the
vehicle location.

If an impact is detected by the airbag ECU, and independently
of the deployment of any airbags, an emergency call is made
automatically.


* These services are subject to conditions and availability.
Consult a CITROËN dealer.
If you purchased your vehicle outside the CITROËN dealer network,
we invite you to have a dealer check the confi guration of these services
and, if desired, modifi ed to suit your wishes. In a multi-lingual country,
confi guration is possible in the offi cial national language of your choice.

If you benefi t from the CITROËN eTouch offer, you also have available
additional services in your MyCITROEN personal space, via the CITROËN
Internet website www.citroen.co.uk.

254
07
1
3
42ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK2
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK
5
7
8
6
9
RADIONAV ESC TRAFFICRADIO
MEDIAMEDIAMEDIA
2 ABC 3 DEF 5 JKL 4 GHI 6 MNO 8 TUV 7 PQRS 9 WXYZ 0 * #
1 RADIO MEDIA NAV ESC TRAFFIC
SETUP ADDR BOOK RADIONAV ESC TRAFFICRADIO
MEDIAMEDIA
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK

Select "Jukebox management" then
"Add fi les" and press OK at each step
to confi rm.
Press the MEDIA button. Press the
MEDIA button again or select Media
Menu and press OK to confi rm.
Insert an audio/MP3 CD, a USB
memory stick or an SD card.







JUKEBOX


Add fi les


Check that the active MEDIA source is that of the medium used
(CD, USB or SD card).

Select "Add fi les from MP3-Disc" for
example and press OK to validate.
Select the tracks required then "Rip
selection" or select all of the tracks using
"Rip all".


Select "[New folder]" to create a new
folder or select an existing folder
(created previously).

Add fi les from MP3-Disc


[New folder]



"Do you want to change the names of
the tracks that will be ripped?": select
"Yes" to change them or "No".

To copy an MP3 CD, then select "Real
time ripping", "Fast ripping"/"High quality
(192 kbit/sec)" or "Standard quality
(128 kbit/sec)" then select "Start ripping".


Confi rm the warning message by
pressing "OK" to start the copy.

OK



Ye sNo

When copying is in progress, switching off the ignition will interrupt the
process but it will resume directly when the ignition is switched on again.

MUSIC MEDIA PLAYERS


COPYING A CD, A USB MEMORY STICK OR AN SD CARD
ONTO THE HARD DISK