2012 Citroen C1 RHD Owner's Manual

8
63 Child safety
ISOFIX child seats recommended by CITROËN and approved for your vehicle
FAIR Bimbofix ISOFIX (size category: C
or A)A
Group 0/1: up to 18 kg

Can be installed facing for ward or rear ward using an ISOFIX base whichis attached to the rings A
and includes a stay which extends
down to the floor of the vehicle. 6 seat body angle positions.
Can be installed facing for ward, attached to the seat using a three-point seat belt.
RÖMER Duo Plus ISOFIX
(size category B1 )

Group 1: from 9 to 18 kg


Is installed in the forward-facing position. Is attached to the rings A
and the upper ring B, referred to as the Top Tether, using an upper strap. Three seat body angles: sitting, reclining, lying down.
Can be installed facing for ward, attached to the seat using a three-point seat belt.
Follow the instructions for fitting child seats contained in the seat manufacturer's installation guide.

64Child safety
Locations for ISOFIX child seats
IUF: seat approved for a Universal Isofix seat, "For ward facing" with the "Top Tether" upper
strap.
IL-SU : seat suitable for the installation of asemi-universal ISOFIX seat, that is:


- "rear facing" fitted with an upper strap or a support

- "forward facing" fitted with a suppor t

- an infant carrier fitted with an upper strap
or a suppor t.
X
: seat not suitable for the installation of
an ISOFIX child seat of the size categoryindicated.



In accordance with the European regulation,
this table indicates the options for the
installation of ISOFIX child seats on the vehicle seats fitted with ISOFIX mountings.
In th
e case of the universal and semi-universal
ISOFIX child seats, the child seat's ISOFIX size category, determined by a letter A, B , B1, C , D,E , F, FG, is indicated on the child seat next to the
ISOFIX logo.
Weight of the child/ indicative age
Less than 10 kg (group 0)Up to 6 months approx
Less than 10 kg (group 0)
Less than 13 kg (group 0+)Up to 1 year approx
From 9 to 18 kg (group 1)From 1-3 years approx
Type of ISOFIX child seatInfant carrier * "rear facing""rear facing""for ward facing"
ISOFIX size categoryFGCDECDABB1
Universal ISOFIX child seats which can be installed on the rear seatsXXXXXIUFIL- SU

*

The ISOFIX infant car seat is fixed to the
lower rings of an ISOFIX seat and occupies
the two rear seats.

9
65 Practical information
)As far as possible, immobilise the vehicle
on level, stable, non-slippery ground. )Apply the parking brake, switch off the
ignition and engage first gear or reverse
for the manual gearbox, position Nfor theelectronic gearbox. The followin
g tools are installed in a carrier,
located in the centre of the spare wheel:
1
. Wheelbrace 2.Jack with handle 3.Removable towing eye

Access to the spare wheel and
the jack in the boot
) Remove the carpet then the plastic cover using the handle.



Tyre pressures

These are indicated on the label positioned on the inner pillar of the left door, see
"Identification markings".



























Changing a wheel
)
If necessary, chock the wheel diagonally
opposite the wheel to be changed.) You must ensure that the occupants leave
the vehicle and wait in a safe location.

Parking the vehicle
To o l s

66Practical information
1. Position the wheel.2.Screw in the bolts fully by hand.1.
Remove the trim. 2.
Slacken the wheel bolts using the
wheelbrace 1.
3. Place the jack 2in contact with one of
the four locations A provided on the
underbody, the one closest to the wheel to
be changed.
4.Extend the jack 2 until its base is in contact
with the ground. Ensure that the centrelineof the jack base is directly below thelocation A
used.
5.Lift the vehicle.
6. Remove the bolts and detach the wheel.3.Pre-tighten the bolts * using the wheelbrace 1.4.
Fold the jack 2
and detach it. *

If your vehicle is fitted with alloy wheels, when tightening the bolts it is normal to notice that the
washers do not come into contact with the spare wheel. It is still fixed securely.
Removing the wheel
Refi tting the wheel

9
67 Practical information
























Changing a bulb
)
Turn the bulb holder A
one quar ter of a turn and remove it. )
Remove the bulb and change it.

5
.Tighten the wheel bolts using the wheelbrace 1.6.Refit the trim. 7. Store the tools and the wheel in the boot.
1
.Sidelamps2.Direction indicators3.Dipped beam / Main beam headlamps
Never go underneath a vehicle suppor tedonly by a jack (use an axle stand). The jack and the tool kit are specific to your vehicle. Do not use them for other
purposes.
In cer tain climatic conditions (low temperatures, humidity), the presence
of condensation on the internalsur face of the headlamps is normal ; it disappears a few minutes after the lighting is switched on.
Front lamps
1. Sidelamps (W5 W)
After changing a wheel: -have the tightness of the bolts and thepressure of the spare wheel checked as soon as possible,
-have the punctured wheel repaired andrefit it on the vehicle as soon as possible. Contact a CITROËN dealer or a qualifiedworkshop.

68Practical information
) Disconnect the connector. )
Remove the rubber cap C.)
Push the side of the tongue D.)
Remove the bulb holder and change thebulb. )
Refit the bulb holder, the tongue then the
rubber cap.
If
you encounter any difficulties, contact a CITROËN dealer or a qualified workshop.



LED daytime running lamps

For the replacement of these lamps, contact aCITROËN dealer or qualified workshop.

Front foglamps

For replacement of these bulbs, contact a CITROËN dealer or a qualified workshop.

)Turn the bulb holder Bone quar ter of a turnand remove it.)Turn the bulb one quar ter of a turn.)Remove the bulb and change it.
If you encounter any difficulties, contact aCITROËN dealer or a qualified workshop.

2. Direction indicators(PY 21 W amber)3. Dipped / Main beam headlamps(H4 - 60/55W)

9
69 Practical information
Rear lamps
1.Brake lamps / sidelamps (P 21/5 W)2. Direction indicators (P 21 W)3.Reversing lamp (P 21 W), left-hand sideFoglamp (P 21 W), right-hand side
These 3 bulbs are changed by removing thelamp unit:) open the boot,)
unscrew the two lamp unit fixing nuts A , )
remove the lamp unit by pulling outwards, )
unclip the harness,
When refittin
g, proceed in the reverse order
and take care to position the bulb holder, the
tabs and the lamp unit correctly.
) remove the bulb holder by spreading the four tongues B
, )
remove the bulb and change it.

70Practical information
repeaters (WY 5 W amber)
Third brake lamp
(Four W 5 W bulbs) Number
plate
lamps (W 5 W)
Do not tighten the screws more than isnecessary, to avoid the risk of breaking
the lamp.
)Pass your hand under the bumper. )Remove the bulb holder turning it onequar ter of a turn.)Remove the bulb and change it.
)
Unscrew the 2 fixing screws A.)
Release the lamp unit by pushing the two
tabs Binwards.)
Disconnect the connector and the rear screen wash pipe.)
Remove the bulb holder.)
Remove the bulb and change it.
When refitting, proceed in the reverse order
and ensure that the lamp unit seal and the rear
screen wash pipe have been put back in place correctly.
)Push the repeater forwards or rearwardsand detach it by pulling towards you. )Disconnect the bulb holder and change it.