2012 CITROEN C-CROSSER ECU

17
FAMILIARI
S
AT I
ON

PASSENGER SAFETY

Front passen
ger’s airbagChild lock
1.
Insert the key.
2
. Select the "OFF"position.
3.
Remove the key. This prevents openin
g of the door con-cerned from the inside.
L
ower or raise the control A to lock or unlock.

109101



ISOFIX mountings

Two rings A, located between the seatAback and seat cushion of the vehicle’s seatare used to install an Isofi x child seat.
A rin
g B
is used to secure the upper strap referred to as the TOP TETHER .
98

II
!
COMFORT
50
FRONT SEATS

Forwards-backwards adjustment
Raise the control bar and slide the seat
forwards or backwards.
When your seat is at the correct dis-
tance, move it forwards and backwards
slightly without using the control bar to
check that it is secured correctly.
Driver's seat cushion height and
angle adjustment
Pull and/or push the control several
times to adjust the height of the seat.
Seat back angle adjustment
Pull the control upwards to adjust the
seat back.
When the seat back is at the correct angle,
release the control.

Manual mode

To prevent the seat back from
moving forward sharply and
knocking you, press on it with
your back or push it with your hand
while operating the lever.

II!
COMFORT
53
REAR SEATS (ROW 2)

Seat back angle adjustment
Pull the control and adjust.
When the seat back is at the correct
angle, release the control.
Sit in the centre of the rear bench seat
to check that the two seats are at the
same level and that the angle of their
seat backs is the same.
Forwards-backwards adjustment
Pull the control towards the outside and
adjust.
When your seat is at the correct dis-
tance, release the control.
To ensure that the seat is secured cor-
rectly, move it forwards and backwards
slightly without using the control. When operating the seats, en-
sure that no person or object
is in the vicinity of the moving
parts to avoid any risk of injury or
damage.
To prevent the seat back from moving
forwards sharply and knocking you,
press on it with your back or push it with
your hand while operating the lever.

The rear seats can be folded in two parts
(1/3 - 2/3).

II
!
COMFORT
55
Folding the second row *



1.
Raise the rear seat lever A
, or
Pull the button in the boot B
for at least one second, or
Pull the rear seat releasing strap C
towards you.

2.
The seat backs fold forwards then the cushion rises and folds forwards.

3.
After carrying out these operations, press on the seat lightly to check that it is secured correctly. Before folding the seats, lower the head restraints fully.
Before folding the seat backs forwards, insert the seat belt buckles in the slots provided for this purpose in the rear seat
cushion.

Before

folding

the



seats

,

ensure that no object

or person is hindering

the execution of the operations.

Do not place luggage on the folded seats.

*
According to version.

II
COMFORT
56

Returning the second row to the normal position



1.
Lower the seat pulling simulta-
neously on the releasing strap A

located at the rear of the cushion
and supporting the seat with your
hand.
Force may be necessary to carry out these operations.
On vehicles fi tted with a third row, the rear of the cushion of the second row is fi tted with a low level lamp B
.
When the releasing strap is pulled, the lamp comes on for approximately 10 seconds to illuminate the fl oor at the base of
the third row.
2.
Press on the cushion to put it in
place until it engages.
3.
Pull the seat back upright pulling si-
multaneously on the releasing strap
located at the rear of the seat back.

4.
After putting the seat back back in
place, push the seat and the seat
back lightly to ensure that they are
secured correctly.

II
!
!
63
STEERING WHEEL MANUAL
HEIGHT ADJU
STMENT



)
Pull the locking lever downwards
(position B
) while supporting the
steering wheel.

)
Adjust the steering wheel to the re-
quired height.
)
Lock the steering wheel adjustment by
pushing the lever upwards (position A
).

The sun visors fold forwards, and to the
side when they are unhooked.
They are fi tted with a courtesy mirror
and a ticket holder.
As a safety precaution, these op-
erations must only be carried out
while the vehicle is stationary.
AREAS FOR TOLL CARDS/CAR
PARK TICKETS


The athermic windscreen has a non-
refl ective zone located above the base
of the rear view mirror.
It is intended for affi xing toll cards and/
or car park tickets.
MAT


When removing the mat on the driver's
side, move back the seat as far as pos-
sible and remove the fi xings.
When refi tting, position the mat cor-
rectly on the pins and clip the fi xings.
Check that the mat is secured fi rmly.
To prevent any risk of jamming
under the pedals:


- only use mats suited to the
fi xings already present in
the vehicle; it is imperative
that these fi xings are used.

- never fi t one mat on top of
another.

II
!
COMFORT
71
*
On 5-seat version only. Raise the boot fl oor to gain access to
this compartment.



Right-hand side enclosed storage
compartment
This storage compartment contains the
tools for changing a wheel.


Storage compartment in the fl oor *







12 V socket (120 W max)
There are four stowing rings in the boot
for securing luggage:


- two rings are located on the boot fl oor,


- two rings are located on the rear
side pillars.

This operates when the ignition switch
is in the "ON" or "ACC" position.
Lift the cover to gain access to the
socket.
Check that the electrical equip-
ment operates on 12 V and that
its maximum electrical power is
120 W.
The prolonged use of electrical equip-
ment without running the engine may
discharge the battery.







Stowing rings

II
!
COMFORT
72
Second installation position
The load space cover can be secured
in two different positions B
, so that the
row 2 seat backs can be tilted.


1.
Reel in the load space cover.

2.
Move one of the slides C
towards
the inside of the vehicle and insert
the tab D
in the installation hole to
be used.
Move the opposite slide in the same
way.

3.
After changing the position, check
that the load space cover is secured
correctly.

Removing the load space cover


1.
Reel in the load space cover.

2.
Move one of the slides C
towards the
inside of the vehicle and raise it.
Release the opposite slide in the
same way.

To put the load space cover in place, carry
out the operations in reverse order.







Load space cover
Unroll the load space cover and install it
in the housing A
.
To store the load space cover, release it
from the housing, it reels in to its initial
position.
Take care not to place heavy
objects on the load space cover
when it is unfolded.
The load space cover can be stored
along the lower tailgate, unless audio
equipment is present.