2012 CITROEN C-CROSSER tow

II
COMFORT
58
REAR BENCH SEAT (ROW 3)

The rear bench seat can be folded. It is
stowed in a location in the fl oor of the
vehicle.

The label on the bench seat back illus-
trates the various steps to the followed
when unfolding and folding the rear
bench seat.

1.
Open the tailgate and the lower tail-
gate (refer to the "Access" section).

2.
Pull the cover A
from the rear and
fi x it to the seat back using the press
stud of the band B
.
Unfolding the bench seat

For comfort, it is advisable to stow
the bench seat when its is not is use.

II
COMFORT
60


1.
Open the tailgate and the lower tail-
gate (refer to the "Access" section).

2.
Lift the cover A
and fi x it to the seat
back using the press stud of the
band B
.
3.
Unlock the head restraints by slid-
ing the controls C
and fold them
onto the seat back.
4.
Pull the grey strap D
and bring the
bench seat towards you. Press on
the bench seat to lock it.

5.
Tilt and push the bench seat for-
wards.
6.
Pull the black strap E
located at the
centre of the seat back to fold the
seat back.
Undo the press stud of the band B
to
put the cover back in place.


Folding the bench seat

II
70
BOOT FITTINGS



1.
12 V socket (120 W max).

2.
Open storage compartment.

3.
Right-hand side enclosed storage
compartment.

4.
Storage compartment in the fl oor * .

5.
Stowing rings.

6.
Left-hand side storage
compartment or audio equipment.

7.
Load space cover.


*
5-seat version only.

II
!
COMFORT
71
*
On 5-seat version only. Raise the boot fl oor to gain access to
this compartment.



Right-hand side enclosed storage
compartment
This storage compartment contains the
tools for changing a wheel.


Storage compartment in the fl oor *







12 V socket (120 W max)
There are four stowing rings in the boot
for securing luggage:


- two rings are located on the boot fl oor,


- two rings are located on the rear
side pillars.

This operates when the ignition switch
is in the "ON" or "ACC" position.
Lift the cover to gain access to the
socket.
Check that the electrical equip-
ment operates on 12 V and that
its maximum electrical power is
120 W.
The prolonged use of electrical equip-
ment without running the engine may
discharge the battery.







Stowing rings

II
!
COMFORT
72
Second installation position
The load space cover can be secured
in two different positions B
, so that the
row 2 seat backs can be tilted.


1.
Reel in the load space cover.

2.
Move one of the slides C
towards
the inside of the vehicle and insert
the tab D
in the installation hole to
be used.
Move the opposite slide in the same
way.

3.
After changing the position, check
that the load space cover is secured
correctly.

Removing the load space cover


1.
Reel in the load space cover.

2.
Move one of the slides C
towards the
inside of the vehicle and raise it.
Release the opposite slide in the
same way.

To put the load space cover in place, carry
out the operations in reverse order.







Load space cover
Unroll the load space cover and install it
in the housing A
.
To store the load space cover, release it
from the housing, it reels in to its initial
position.
Take care not to place heavy
objects on the load space cover
when it is unfolded.
The load space cover can be stored
along the lower tailgate, unless audio
equipment is present.

III
81
"Tailgate open" warning


This warning lamp comes on on
the instrument panel screen when
the tailgate is not closed correctly.
LOWER TAILGATE

Openin
g



)
Push the handle C
to the right and
tilt the tailgate D
gently.



Closing



)
Raise the tailgate D
, push it to close
it, then check that it is secured
correctly. Before opening the tailgate, ensure
that no one is within the radius of
opening.
For reasons of safety and correct op-
eration, do not drive with the tailgate
open.
If the battery is disconnected, the
tailgate cannot be opened.
Do not climb onto the lower tailgate
and do not subject it to heavy knocks,
it may be damaged.
Always close the lower tailgate and
check that it is secured correctly be-
fore closing the main tailgate.
When closing the lower tailgate, en-
sure that no person or object is in the
proximity of the moving parts to avoid
any risk of injury or damage.
Do not open the lower tailgate when
a towbar is fi tted.
Maximum authorised weight on the
lower tailgate when open: 200 kg
.
Tailgate release

This enables the tailgate to be unlocked
in the event of a central locking fault.


- Fold back the rear seats to gain ac-
cess to the tailgate release from in-
side the boot.

- Remove the plastic cap from the
opening A
in the tailgate interior
pillar.

- Move the control B
to the right to
unlock and open the tailgate.

IV
VISIBILITY
86
LIGHTING STALK

Additional lighting

Other lamps are installed to fulfi l the re-
quirements of particular driving conditions:


-
rear foglamps to be seen from a distance,


- front foglamps for even better visibility,

- daytime running lamps to be seen
during the day.
Certain functions of the lighting stalk
(automatic illumination of headlam-
ps, sensitivity) can be confi gured
via the colour screen "Equipment"
menu.

Manual controls

The lighting is controlled directly by the
driver by means of the ring A
and the
stalk B
. Lamps off.





Automatic illumination of head-
lamps.
Sidelamps.

B.
Stalk for switching headlamps: pull
the stalk towards you to switch the
lighting between dipped and main
beam headlamps.
In the lamps off and sidelamps modes,
the driver can switch on the main beam
headlamps temporarily ("headlamp
fl ash") by maintaining a pull on the
stalk.

Displays

Illumination of the corresponding indica-
tor lamp in the instrument panel confi rms
that the lighting selected is on.
A.
Main lighting mode selection ring:
turn it to position the symbol re-
quired facing the mark.
Dipped headlamps or main
beam headlamps.

Main lighting

The various front and rear lamps of the
vehicle are designed to adapt the driv-
er's visibility progressively in relation to
the climatic conditions:


- sidelamps, to be seen,

- dipped beam headlamps to see
without dazzling other drivers,

- main beam headlamps to see clearly
when the road is clear.

IV
VISIBILITY
90
WIPER CONTROLSManual controls
The wiper commands are issued direct-
ly by the driver by means of the stalk A

and the ring B
.
single wipe.
Windscreen wipers

A.
wiping speed selection stalk:
park.
intermittent (the speed can be
set manually),
slow.
fast.




B.
intermittent operation or rain sensor
sensitivity adjustment ring.
You can increase or decrease:


●
the wiping frequency when the in-
termittent mode is active,

●
the sensitivity of the rain sensor
when the automatic mode is active.


- "+": high sensitivity.

- "-": low sensitivity.

Headlamp wash
Press the end of the lighting stalk to
activate the headlamp wash, when the
dipped beam headlamps are on.

Programming
An automatic control mode is also avail-
able, the automatic rain sensitive wind-
screen wipers.











Windscreen wash
Pull the wiper stalk towards you. The wind-
screen wash then the wipers operate for a
set time.
The headlamp wash is also activated if
the dipped
beam
headlamps are on
. Certain windscreen wiper func-
tions (intermittent operation, ...) can
be confi gured via the colour screen
"Equipment" menu.



Model with intermittent wiping



Model with AUTO wiping
or

automatic rain sensitive wipers
(the speed can be set manually).