2012 CITROEN C-CROSSER DAG display

VI
!
SAFETY
104 The ASC/TCL systems offer ex-
ceptional safety in normal driving,
but this should not encourage the
driver to take extra risks or drive at
high speed.
The correct functioning of these sys-
tems depends on observation of the
manufacturer's recommendations on:


- wheels (tyres and rims),

- braking components,

- electronic components,

- assembly and repair procedures.
After an impact, have these systems
checked by a CITROËN dealer or a
qualifi ed workshop.


Deactivation
In exceptional conditions (starting a ve-
hicle which is bogged down, stuck in
snow, on soft ground, ...), it may be ad-
visable to deactivate the ASC system,
so that the wheels can move freely and
regain grip.


)
Press the "ASC OFF"
button, locat-
ed to the left of the steering wheel,
until the ASC OFF symbol appears
on the instrument panel screen.
The display of this symbol in the top
right corner of the instrument panel
screen indicates that the ASC and TCL
systems are deactivated.
Reactivation
These systems are not reactivated au-
tomatically above 30 mph (50 km/h).


)
Press the "ASC OFF"
button again
to reactivate them manually.
Switching off of the symbol in the top
right corner of the instrument panel
screen indicates the reactivation of the
ASC and TCL systems.

Operating fault

The displaying of this mes-
sage on the instrument panel
screen indicates a malfunc-
tion of these systems.
Contact a CITROËN deal-
er or a qualifi ed workshop to have the
ASC/TCL systems checked.
TRAJECTORY CONTROL
SYSTEMS

Activation
These systems are activated automati-
cally each time the vehicle is started.
They operate when the vehicle speed is
higher than 10 mph (15 km/h).

Traction control and automatic
stability control
Traction control optimises traction to
prevent wheel spin, by acting on the
brakes of the driving wheels and on the
engine.
Automatic stability control acts on the
brake of one or more wheels and on the
engine to keep the vehicle on the tra-
jectory required by the driver.
They come into operation in
the event of a grip or trajectory
problem.
This is indicated by fl ashing
of this symbol on the instrument panel
screen.



Associated systems which guarantee
the directional stability of the vehicle
within the limits of the laws of physics:


- traction control (TCL),

- automatic stability control (ASC).

VI
SAFETY
106

Front seat belt not fastened/
unfastened warning lamp
When the ignition is switched
on, this warning lamp comes
on accompanied by an au-
dible signal for a few seconds
if the driver has not fastened
their seat belt.
Rear seat belts
Each rear seat is fi tted with a three-point
inertia reel seat belt with force limiter.

Fastening


)
Pull the strap, then insert the tongue
in the buckle.

)
Check that the seat belt is fastened
correctly by pulling the strap.


Unfastening


)
Press the red button on the buckle.

If the driver does not fasten their seat
belt within one minute after switching on
the ignition, the warning lamp fl ashes
accompanied by an intermittent audible
signal and a display on the instrument
panel screen.
The warning lamp, the audible signal
and the display stop after approximate-
ly 90 seconds and return until the driver
fastens their seat belt.
If the seat belt is unfastened while the
vehicle is moving
, you are alerted by
the same warnings.
Storing after use



1.
Pass the seat belt under the support A
located on each rear side pillar,

2.
Insert the tongue in the slot B
of the
support.


Rear buckles


)
Store the buckles in the locations A

and B
provided for this purpose in
the rear seat cushion.


Driver's seat belt
Outer rear seat belts
Front passenger's seat belt
When the ignition is switched on, this
warning lamp comes on the centre
console panel.
It is accompanied by an audible signal
for a few seconds if the passenger has
not fastened their seat belt.
If the seat belt is unfastened while the
vehicle is moving
, you are alerted by
the same warnings.

VI
!
!
SAFETY
109 If the airbag warning lamp and
the display come on continuously,
do not install a "rear facing" child
seat on the front passenger seat.
Contact a CITROËN dealer or a
qualifi ed workshop.

Operating fault
If this warning lamp comes on on the
instrument panel and this display ap-
pears on the instrument panel screen,
contact a CITROËN dealer or a qualifi ed
workshop to have the system checked.
The airbags may no longer be deployed
in the event of a serious impact. To ensure the safety of your
child, the passenger's airbag
must be deactivated when you
install a "rear facing" child seat on
the front passenger seat.
Otherwise, the child would risk being
seriously injured or killed if the airbag
were triggered.
This warning lamp comes on in the cen-
tre console panel when the ignition is
on and until the airbag is reactivated.
Reactivation
When you remove the child seat, turn
switch A
to the "ON"
position to reacti-
vate the airbag and so ensure the safe-
ty of your front passenger in the event
of an impact.
The associated warning lamp goes off.
Deactivation
Only the front passenger's airbag can
be deactivated:


)
with the ignition off
, insert the key
in the passenger airbag deactiva-
tion switch A
,

)
turn it to the "OFF"
position,

)
remove the key.

VI
!
SAFETY
11 0
Lateral airbags
System which protects the driver and
passenger in the event of a serious side
impact in order to limit the risk of injury
to the chest.
Each lateral airbag is fi tted in the front
seat back frame, on the door side.

Activation
The lateral airbag is triggered unilater-
ally in the event of a serious side impact
applied to all or part of the side impact
zone B
, perpendicular to the longitudinal
centreline of the vehicle on a horizontal
plane and directed from the outside to-
wards the inside of the vehicle.
The lateral airbag infl ates between the
front occupant of the vehicle and the
corresponding door trim panel.

System which protects the driver and
passengers (with the exception of the
rear centre passenger and the passen-
gers in row 3) in the event of a serious
side impact in order to limit the risk of
injury to the head.
Each curtain airbag is fi tted in the pillars
and the upper section of the passenger
compartment.
Deployment
The curtain airbag is deployed at the
same time as the corresponding lateral
airbag in the event of a serious side im-
pact applied to all or part of the side impact
zone B
, perpendicular to the longitudinal
centreline of the vehicle on a horizontal
plane and directed from the outside to-
wards the inside of the vehicle.
The curtain airbag infl ates between the
front or rear occupant of the vehicle and
the windows.
In the event of a minor impact or
bump on the side of the vehicle
or if the vehicle rolls over, the
airbag may not be deployed.
In the event of a rear or front colli-
sion, the airbag is not deployed.
Impact detection zones


A.
Front impact zone.

B.
Side impact zone.



Operating fault

If this warning lamp comes on in the instru-
ment panel and this display appears in the
instrument panel screen, contact a CITROËN
dealer or a qualifi ed workshop to have the
system checked. The airbags may no longer
be deployed in the event of a serious impact.

VII
DRIVING
11 2
PARKING BRAKE


Releasing


)
Pull the lever up and press the button
A
to release the parking brake.

5-SPEED MANUAL GEARBOX


Engaging 5 th or 6 th gear


)
Move the gear level fully to the right
to change to 5 th or 6 th gear.


Applying


)
Pull the parking brake lever up to
immobilise your vehicle.
When parking on a slope, direct your
wheels towards the pavement and apply
the parking brake.

When the vehicle is being
driven, the display of this
message indicates that the
parking brake is still on or has
not been properly released.

6-SPEED MANUAL GEARBOX


Engaging reverse


)
Lift the sleeve below the gear knob
and move the gear lever to the left
and then towards the front.

Reverse gear can only be engaged
when the vehicle is stationary with
the engine idling.

VII
DRIVING
11 4

Stopping - Starting on a slope


Do not use the accelerator pedal to im-
mobilise the vehicle on a slope, apply
the parking brake instead.
When starting on a slope, accelerate
gradually while releasing the parking
brake.


Switching to sequential mode

Once you have moved off, you can
switch to sequential mode by selecting
position +/-
.

"D"
disappears and the gears engaged
appear in succession in the instrument
panel screen.
The gear change requests are only carried
out if the engine speed permits it.
Take your foot off the accelerator pedal
gently to engage the gear.

Switching to automated mode


Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position D
.

"D"
appears in the instrument panel
screen.
The gearbox then operates in auto-active
mode, without any action on the part of
the driver.
It continuously selects the gear most
suited to the conditions of:


- driving style,

- road characteristics,

- vehicle load.
To optimise driving comfort and obtain
the most suitable gear, avoid sharp
variations in the pressure on the accel-
erator pedal.

Auto sequential mode
In the automated mode, you can take
over control temporarily at any time using
the steering mounted controls.
The use of these controls permits manual
selection of the gears in situations which
require a faster changedown than that
offered in automated mode (arrival at a
roundabout, exit from a car park with a
steep gradient, overtaking...). Stopping the vehicle
Before switching off the engine, you
can:


- move to position N
to leave the
gearbox in neutral.

- leave a gear engaged, such as fi rst
or reverse.
In both cases, you must apply the parking
brake to immobilise the vehicle.
Operating anomaly

With the ignition on, if the message "Slow
down"
or "Maintenance required"
ap-
pears in the multifunction screen, this indi-
cates a gearbox malfunction.
When a message is displayed, carry
out the following operations:


- slow down and stop your vehicle in
a safe place,

- place the lever in position N
and let
the engine run,

- open the bonnet to allow the engine
to cool.
If the message disappears for a long
period, you can set off again.
If the message remains displayed or
appears frequently, contact a CITROËN
dealer or a qualifi ed workshop without
delay.
Press the brake pedal fi rmly
while starting the engine.

Start the engine. "N"
appears in the in-
strument panel screen.

Select fi rst gear (position D
or +/-
) or reverse
(position R
).

Release the parking brake.
Release the brake pedal then accelerate.

"D"
or "1"
or "R"
appear in the instrument
panel screen. The gearbox engages the gear re-
quested if the engine speed permits it.
The gear engaged appears.
To return to the automated mode, press
the back of the "+/OFF"
control for ap-
proximately 2 seconds.
At low speeds, when approaching a
stop or traffi c lights for example, the
gearbox changes down to fi rst gear au-
tomatically.

VII
DRIVING
115
DCS GEARBOX
The six-speed electronically controlled
gearbox offers a choice between the
comfort of automatic regulation or the
pleasure of manual gear changing.
This gearbox has three driving modes:


- a manual
mode for changing of the
gears by the driver using the steering
mounted controls or the gear lever,

- a " Normal
" automatic mode for eco-
nomical control of the gears (every-
day use),

- a " Sport
" automatic mode which
permits a more dynamic style of
driving, with improved acceleration
and optimised engine braking.
When you move the lever in the gate
to select a position, the corresponding
indicator or message is displayed in the
instrument panel.

P.
Park.

R.
Reverse.

N.
Neutral.

D.
Drive (Automatic mode).

NORMAL.
Normal mode.

SPORT.
Sport mode.

1,2,3,4,5,6.
Gear engaged during manual
operation.


Displays in the instrument panel


P
: park.
Gear lever positions

With your foot on the brake, this
position permits starting of the
vehicle.
To exit position P
, raise the ring on the
gear lever.

R
: reverse gear.
With the vehicle stationary, keep your
foot on the brake pedal and push the
gear lever forwards.

N
: neutral.
With your foot on the brake, this position
also permits starting of the vehicle.

D
: automatic mode.
Move the lever rearwards.

+/-
: manual mode with gear changing
using the lever.

VII
DRIVING
118

Operating fault

Reverse gear
Flashing of the indicator R
in the instru-
ment panel screen, accompanied by an
audible signal, indicates a malfunction
on engaging the gear:
Press the brake pedal, position the gear
lever in position N
and engage reverse
gear again.

With the ignition on, if this warning
light comes on, accompanied by vi-
bration in the pedals and the message
"Maintenance required"
on the in-
strument panel display, this indicates a
gearbox malfunction.
If the message is displayed, carry out
the following operations:


- slow down and stop your vehicle in
a safe place,

- place the lever in position P
or N
,
apply the parking brake and let the
engine run,

- open the bonnet to allow the engine
to cool.
If the message disappears for a long
period, you can set off again.
If the message remains displayed or
appears frequently, contact a CITROËN
dealer or a qualifi ed workshop without
delay.

Overheating of the engine may re-
sult in unwanted declutching of the
gearbox.