-On -when the parking system is switched
on, either the visual display or the picture
from the rearview camera is disp layed .
Warning tones
- Front volume* -
front sensor vo lume
- Front frequency* -front sensor frequency
-Rear volume -rear sensor volume
-Rear frequency -rear sensor frequency
-In -ca r entertainment fader/Music volume
while parking -
when the parking system is
switched on, the volume of the active audio source is lowered.
The newly adjusted value is briefly heard from
the signal generator.
(D} Tips
- The warning tones can also be adjusted
direct ly by the v isual disp lay* or the pic
ture from the rearview camera*. Simply
press the
Settings* control button .
- Changed settings are activated when
parking system is switched on aga in.
- The settings are automatically stored
and ass igned to the remote control key.
Trailer hitch
Applies to vehicles: with rear park assist/Audi parking sys·
tem plus with rearview camera and trailer hitch
For vehicles with a factory installed trai ler
hitch, or a trai ler hitch installed according to
factory specifications, the parking system rear
sensors do not come on whenever you shift in
to reverse gear or when you press the P
11,
switch*. If you install a hitch yourself, th is
function may not work . In general the follow
limitations may come up:
Rear park assist*
There is no warning for distances to the rear.
Audi parking system plus with rearview
came ra*
There is no warning for distances to the rear .
The front sensors remain activated. The visual
display switches to the trailer towing mode.
The picture from the rearview camera will not
Parking system 149
show the orientation lines nor the blue surfa
ces.
Error messages
Applies to vehicles: with rear park assist/Audi parking sys
tem plus with rearview camera
There is an error in the system if the LED on
the
P" 1! switch* is blinking and you hear a con
tinuous alarm for a few seco nds after switch
ing on the park ing system or when the park
ing system is already activated. Have your au
thorized Audi dea ler correct the error .
(D Tips
If the error is not corrected before you
switch off the ignition, when you switch on
the parking system again, the LED in the
p,,1, switch* will blink .
156 Hom eli nk®
Homelink ®
Universal remote
control
General information
Applies to vehicles: with Home link® universal remote
control
The Homelink ® feature can learn up to three
radio frequency codes for most current trans
mitters used for operating garage doors, es tate gates, home or outdoor lighting sys
tems, and other devices.
You must first program the Homelink ® trans
mitter before you can use the system
~ page 157, Programming the Homelink ®
transmitter.
In order to program the Home link ® transmit
ter for devices utilizing rolling code, a second
person on a ladder who can safe ly reach the
garage door opener motor is recommended. I t is also necessary to locate the "learn" but
ton on your garage door opener motor . Refer
to the operating instructions for the opener,
as the location and color of this button may
vary by manufacturer.
You can still use the origina l remote control
for the device at any time .
.&_ WARNING
-
- Never use the Homelink ® transmitter
with any garage door opener that does
have not the safety stop and reverse fea
ture as requ ired by federa l safety stand
ards. Th is includes any garage door open
er model manufactured before April 1,
1982.
- A garage door opener which cannot de
tect an object, signa ling the door to stop
and reverse does not mee t current feder
al safety s tandards. Using a garage doo r
opener without these features increases
risk of serious inj ury or death.
- F or sa fety reasons never release the
parking brake or start the engine w hile
anyone is stand ing in front of the vehicle . -
A garage door or an estate gate may
sometimes be set in mot ion when the
Homelink ® remote control is being pro
grammed. If the device is repeatedly ac
tivated, this can overstrain motor and
damage its e lectr ical components -an
overheated moto r is a fire hazard!
- To avo id possible injuries or property
damage, please always make abso lutely
certain that no persons o r objects are lo
cated in the range of motion o f any
equ ipment being ope rated .
(D Tips
-If you would like more information on
Homel ink ®, where to purchase the
Homel ink ® compatib le produc ts, or
would like to purchase the Homelink ®
Home Lighting Package, please call to ll
free: 1-800-355-3515 .
- For Declaration of Compliance to United States FCC and Ind ustry Canada reg ula
tions~
page 322.
Programming the Homelink®
transmitter
A pplies to vehicles: with Home link® universa l remote
co ntrol
The transmitter is programmed in two phas·
es. For rolling code transmitters, a third
phase is also necessary .
.- :-::::: . ... ........ -. ----· . ...... ........ .l
-·-·-· -·-· -·..: ··-· ---- -·- ·· ..._~ -- · ····
111111
-
Fi g. 1 79 Overhead console: Homelink ® keypad
Fig. 1 80 Front bumper, d rive r side: loca tion of tra ns
mitter un it
Pha se 1:
programming the o verhead keypad
l. Make sure your vehicle is wit hin ope rating
range of the remote controlled garage
door ope ner .
2 . Set the pa rking brake
c:> .& in General in
formation on page 156.
3 . Turn the ignition o n. D o not sta rt the en
g ine!
4. Press and hold the two outs ide Home
Link ® buttons
(D and ® for approxi
mately 20 seconds until indicator light @
c:> fig. 179 begins to flash. Then release
both buttons. Do not hold the buttons for
l onger than 30 seconds .
~ This procedure only needs to be perfo rmed
on ce .
It erases the factory-set default codes
and does not have to be repeated to p ro
gram ad dit io na l remote contro ls .
Homelink ® 15 7
5. Press and ho ld the Homelink ® button (D ,
0 or ® until the indicator light@
starts flash ing
slowly . Release the button.
~ The system will remain in programming
mode for 5 minutes.
Go to the front of the
vehicle and proceed with phase 2 .
Phase 2 :
programming the bumper mounted trans
mitter
6 . Hold the
original remote control at a d is
tance between
0 -6 in. (0 -15 cm) from the
bumper below the appropr iate headligh t
f or yo ur vehicle
c:> fig. 180 (u se the short
est distance possible) .
7 . Aim the remote control just below the
driver s ide headlight.
8. Press and ho ld the activation button on
the remote control.
~ May be different in Canada. If so, press and
re-press (cycle) the activation button on your
remote cont ro l every two seconds .
9. The emergency flashers w ill flash
three
time s
(a fter about 15 -60 seconds) when
the programming is successful. Re lease
t h e button on the remote contro l.
~ To program more devices, repeat steps 4 to
9.
10. Press and hold the trained Homelink ®
button and observe the indicator light @
c:>fig . 179 .
~ If the indicator light is solid/contin uous,
programm ing is comp lete and your device
should a ctivate when you press and release
t he t rained Homelink ® bu tton.
~ If the ind icator light blinks rapidly for 2 sec
onds and is then a solid/continuous light,
proceed w ith phase 3 to program a rolling
code device.
Phase
3: rolling code programming
~ A se con d person o n a ladde r who c an safe ly
reach the garage door opener motor is rec
ommended .
11. Locate the "learn" button on the garage
door opener motor (refer to the operating
instruct ions for the opener, as the loca·
t ion of t his button may vary by manufac-
turer) . .,.
158 Homelin k®
12. Press and release the learn button on the
garage door opener motor.
• Note: once the button is pressed, there are
30 seconds in which to initiate the next
step.
13 . On the Homelink ® keypad inside the vehi
cle, firmly p ress a nd hold the Homelink ®
button previously p rogramm ed in phases
1 and 2 for two seconds and release. Re
pea t this sequence
twi ce .
• Some vehi cles may require the p ress/hold/
release sequence up to t hree times to com
plete the training p rocess.
• HomeLink ® should now activate your rolling
code equipped device.
If t h e 5 minute time limit is exceeded, the
emergen cy flashers will flash one time to in
d icate that the process has been terminated.
In th is case, repeat steps 4 through 9.
If t he emergency flashers do not flas h
three
times (after about 15-60 seconds), program
ming was not successful. In this case, repeat
steps 4 through 9.
Remote control units for ga rage doo r openers
in Canada are set to stop transmitting radio
frequency signals after two seconds. This time
may not be sufficient for the Homelink ® sys
tem to learn the radio frequency s ignal. Per
form all other steps as described above .
Operating the Homelink® transmitter
App lies to vehicles: with Home link® universa l remote
co ntrol
The HomeLink ® transmitter works in the
some manner as the original hondheld re mote control that come with the system.
- ·······-··
········-·· •••••• . -.-.----·-·..: ··-·-·-·-·-··
··-·-·-·-·-·· .. -.... - - - ~-. -
fillTI ffUll
-
Fi g. 18 1 Overhead co nsole: Homelink ® keypad
• Press the appropr iate programmed b utton
(D , ® or@ to activate the desired remote
cont ro l function
~ A in General informa
tion on page 156.
Reprogramming a single button
Applies to vehicles: wit h Ho meli nk® uni versal remote
contro l
A HomeLink ® button can be reprogrammed
individually wi thou t affe cting the o ther but
ton allocations .
Programming the overhead keypad
.. Press the appropr iate Homelink ® button
until the i ndicator light begi ns flashi ng
slowly .
Programming the bumper mounted trans
mitter
1. Hold the original remote control at a dis
tance between 0-6 i n. (0 -15 cm) from the
bum pe r below the appropr iate headlight
f or yo ur vehicle (use the shor test dis tance
possible).
2. Aim the remote control just below the
driver s ide headlight .
3. Press and ho ld the act ivation button on
the remote control.
4 . The emergency flashers w ill flash
three
tim es
(after about 15 -60 seconds) when
the p rog ramming is successful. Now re
l ease the button on the remo te control.
.. If the dev ice utilizes a rolling code, p lease
follow phase 3 of¢
page 157, Program
ming the Home Link ® transmitter
for ro lling
code programming.
This procedure will cause the existing pro
gramming on the Homelink ® button to be
erased !
Erasing the programming of the
Homelink® transmitter
Applies to vehicles: with Homelink® unive rsal remote
control
When you erase the programming, the pro
gramming on all three of the transmitter channels with be lost!
.,. Perform steps 1 to 4 as described on
¢page 157, Phase 1: program
ming the overhead keypad .
When completed, the Homelink ® system will
be in the programming mode and is then
ready to learn the codes for remote controlled
devices .
@ Tips
-Programmed buttons cannot be erased
individually.
- For security reasons you are advised to
erase the programming of the Home Link ® system before yo u sell your vehicle. Homelink
® 159
322 Consumer Information
Technical Modifications
Our guidelines must be complied with when
technical modifications are made .
Always consult an authori zed Audi dealer be
fo re starting work on any modifications .
This will he lp ensure that vehicle function,
performance and safety are not impaired
¢ &. .
Attempting to work on electronic components
and the software used with them can cause
malfunctions. Because of the way electronic
componen ts are interconnected with each
other, such malfunctions can also have an ad
verse affect on other systems that are not di
rectly involved . Th is means that you risk both
a substantial reduction in the operational
safety of your vehicle and an inc reased wea r of
ve hicle parts ¢
A:,..
Author ized Audi dealers will perform th is
wo rk in a p rofessiona l and competent manner
or, in special cases , refer you to a professional
company that specializes in such mod ifica
tions .
A WARNING
Improper repairs and modifications can
change the way vehicle systems work and
cause damage to the veh icle and serious
personal injury.
-
If emergency repairs must be performed
elsewhere, have the ve hicle examined by
an authorized Audi dealer as soon as possi
ble.
Declaration of
Compliance, Telecom
munications and
Electronic Systems
Radio Frequency Devices and Radio Communi
cation Equipment User Manual Notice .
The manufacturer is not responsib le for any
radio or TV interference caused by unauthor
i z ed modifications to this equipment.
D ev ices
The following dev ices each comply with FCC
Part 15.19, FCC Part 15.2 1 and RSS -Gen Iss ue
1:
- Adapt ive cru ise control
- Conven ience key
- Aud i side assist
- Cell phone package
- Electron ic immobili zer
- Homelink ® universal remote contro l
- Remote control key
FCC Part 15.19
This device complies with part 15 of the FCC
Ru les . Operation is subject to the fo llow ing
two conditions :
(1) This device may not cause harmful inter
ference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation .
FCC Part 15 .21
CAUTION:
Changes or mod ificat ions not expressly ap
proved by the party responsible for compli
ance could void the user 's authority to operate
the equipment .
RSS-Gen Issu e 1
Operation is subject to the fo llow ing two con
ditions:
(1) this device may not cause inte rfe rence ,
and
328 Index .:..:..:..::....::.....:..._ ___________________________ _
Declaration of compliance
Adaptive cruise control ............. 322
Audi side assist ................... 322
Cell phone package ....... .. .. .... . 322
Convenience key .......... .... .... . 322
Electronic immobilizer ......... .. ... 322
H omelink ® universal remote control .. 322
Remote control key ........... .. .. . 322
def What does this mean when it appears in
the trip odometer display? ..... .. .. .. 12
Defective light bulb warning . . . . . . . . . . . 23
Defrosting/defogging the windows . . . . . . 94
Defrosting/defogging windows ... .... .. 96
Determining correct load limit ... .. .. . 282
Diesel fuel . . . . . . . . . . . . . . . . . . . . . . . . . 2 5 1
Diesel particu late filter . . . . . . . . . . 37, 229
Digital clock . .. . ........ .. .. .. .. .. .. 11
Digital compass ........... .. .. .. .. .. 69
Digital speedometer ............ .... .. 22
Dimensions .. ................ ... ... 315
Dimming the rearview mirror .. .. ...... 69
Dipstick Reading the dipstick properly ..... .. . 263
Distance control system
refer to Adaptive cruise contro l .. .. .. . 113
Doors Power child safety lock .... .. .. .... .. 48
Driver information system ............. 21
Digital speedometer .............. . . 22
Driver information messages . . . . . . . . . 30
Open door or rear lid warning . . . . . . . . . 22
Outside temperature display .. .. .. .... 22
Sound system display ......... .. .. .. 21
Driver seat
refer to Seating position ... .. .. .... . 161
Driver's seat . . . . . . . . . . . . . . . . . . . . . . . . 72
Driver 's seat memory . . . . . . . . . . . . . . . . . 73
Activating remote control key ... .. .... 74
Recalling a seat posit ion . . . . . . . . . . . . . 73
Storing a seat position ....... .. .... .. 73
Driving message s . . . . . . . . . . . . . . . . . . . . 30
Driving mode
refer to Adaptive Air Suspension . 150, 152 Driving
offroad
Driving through water ............ .. 233
Driving tips . ... .. ... .......... .. .. 232
Ru les of behavior . ............. .... 232
Sand and mud ... ............. .... 233
Snow -covered g round ............. . 233
Unpaved roads ... ... ... .... ..... .. 233
Driving safe ly ... .. ... .......... .. .. 160
Driving through water ........... .... 233
Driving time . . . . . . . . . . . . . . . . . . . . . . . . 24
Duplicate key ..... .. ........... .. .. . 38
Dust filter Climate controls ............... .. .. . 91
E
Easy entry feature .. ... ... .... ..... .. 104
Efficiency program .............. .. .. . 26
Fuel economy messages ........ .. .. . 27
Memory levels . . . . . . . . . . . . . . . . . . . . . 25
Other equ ipment . .......... ...... .. 27
E lectric seat adj ustment
refer to Power seat . . . . . . . . . . . . . . . . . 72
El ectronic differential lock ( EDL )
How the system works .......... .... 221
Warning/indicator lights ........ .. .. . 18
Electronic immob ilizer ... ........... .. 40
E lectronic power contro l
(EPC) warning/indicator light . . . . . . . . . 15
Electronic speed limiter .......... .. .. . 28
Electronic Stability Control (ESC)
Hill descent control ............... . 219
How the system works .......... .. .. 219
Offroad mode .. .. ............. .. .. 219
Warning/indicator lights ........ .. .. . 16
Emergency flasher ........... ...... .. 60
Warning/indicator lights ........... .. 16
Emergency lock ing of doors ......... .. . 45
Emergency operation Rear lid ... .... .. .. ........... .. .. . 48
Emergency starting ..... .. ... ..... .. 308
Emergency towing .............. .... 310
En ergy management .............. .. 225
Battery power ... .. ........... .. .. 227
Driver notification . . . . . . . . . . . . . . . . . 22 7
Rear seats (four-zone automatic comfort
air conditioning) ....... ... ... ... ... 101
Steer ing whee l ... ....... ... .. .. .. . 101
Washer jets . . . . . . . . . . . . . . . . . . . . . . . 63
H eat ing
Climate controls . . . . . . . . . . . . . . . . . . . . 91
H eavy clothing and safety belts ... . ... . 173
High beam...................... S7, 60
Warn ing/ indicator lights ............. 18
H igh voltage warning label . ... .. .. .. . 3 14
H ill descent control ........ .. .. .. .. . 219
Hill hold Starting on hills .............. ..... 110
H omelink ® universal remote control
H ood 156
Opening . .. .. ........... .. .. .. ... 258
Release lever ................ ..... 258
Horn ............................... 8
H ow are c hild restra int system anchors re
l ated to child safety . . . . . . . . . . . . . . . . . 212
H ow many airbags does my vehicle have? 186
How often sho uld I check my tire pres-
sures? ............................ 281
H ow sa fety belt pretensioners work ... . 17 7
H ydroplan ing .. ........... .. .. .. .. . 285
I
Ignition key ............... ........ . 105
I gnition lock ... .... .... ... .. .. .. ... 105
Malfunction . . . . . . . . . . . . . . . . . . . 34, 37
I gnition lock pos itions ............... 105
Important things to do before driving .. 160
I mproperly worn safety be lts ... .. .. .. . 17 7
Indicator lights . . . . . . . . . . . . . . . . . . . . . . 14
A irbag system ........... ......... 190
PASSENG ER AIR BAG OFF ........... 190
Infant seats .................... ... 205
I nflatable spare tire ..... ... .. .. .. .. . 296
Inflating ... .. .... .... ... .. .. .. ... 297
I nstal ling c hild safety seats
Safety belts ................. ..... 209
Install ing the upper tether strap on the
anchorage . . . . . . . . . . . . . . . . . . . . . . . . . 217
Instrument cluster illumination . ... .. .. 13
I nst rumen ts and controls ............. 10
General illus tra tion ........... ....... 8
Inde x 331
Interior lights
Front ... .. .. .. .... . ... ...... ... .. . 61
Rear ... .. .. .. .. .. . .. ... .... ... .. . 61
Intermitten t wiping
Rain sensor . . . . . . . . . . . . . . . . . . . . . . . . 63
J
Jack .............................. 295
Jump-starting ...................... 308
Jumper cables ... .. .. . ... ...... ... .. 309
K
Key ............................... . 38
Battery replacement . . . . . . . . . . . . . . . . 40
Coded settings ... .. . ... ...... ... .. . 91
Convenience opening and closing of win -
dows ... .. .. .. .. .. .. .. .. .... ... .. . 53
Emergency key ..................... 38
Key replacement .................. . 38
Master key . . . . . . . . . . . . . . . . . . . . . . . . 38
Vale t key . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Key coded settings
Climate controls .................... 91
Keyless entry remote contro l ........... 38
K ick-down
t iptron ic® ... .. .. .. . .. ....... ..... 140
L
LATCH
Desc ription .. .. .. .. .. ............ .
Gu idance fixtures for lower anchorages
Installing a ch ild restra int .......... . 212
213
214
215
Loca tion ......................... 213
Mo unting and releasing the anchorage
hook ... .. .. .... .. . .. .. ..... ... .. 215
Latera l ang le .. .. ... ... ............. 232
Leather . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
Cleaning ......................... 247
Leve l adjustment
refer to Adaptive Air Suspension . 150, 152
Lifting jack ... .. .. .. . .. ....... ... .. 300
Lifting vehicle ...................... 312
•
•