2012 AUDI Q7 remove seats

192 Airbag sys tem
-the safety be lt is being properly worn and
that there is not a lot of slack in the safety
belt webbing,
- accessory seat covers or cushions or other
t h ings that may cause an incorrect reading
or impression on the weight-sensing mat
under the upholstery of the seat have been
removed from the front passenger seat,
- a safety belt extender has not been left in
the safety belt latch for the front passenger
seat.
In addition to the
PASSENG ER AIR BA G OFF
light in the center of the instrument panel,
the message
PASSENGER AIR BAG OFF or
PA SS ENGER AIR BA G ON will briefly appear
in the instrument cluste r display . T his is to in­
form the drive r of the current front passenger
a ir bag status.
Important safety instructions on
monitoring the Advanced Airbag System
A WARNING
An airbag system that is not funct ioning
prope rly cannot provide supplemental pro­
tect ion in a frontal crash.
- If the airbag indicato r light comes on, it
means that the re may be someth ing
wrong with the Advanced A irbag System.
It is possible that the airbag will inflate
when it is not supposed to, or w ill not in­
flate when it should.
- Have the airbag system inspected imme­
diately by your author ized Audi dealer .
A WARNING
If the front airbag inflates, a ch ild witho ut
a child restra int, or in a rearward-facing
child safety seat, or in a forward -facing
child restraint that has not been properly
installed will be seriously injured and can
be killed.
- Even though your veh icle is equipped
with an Advanced Airbag System, make
certain that a ll children , especially 12
years and younge r, a lways ride on the back seat properly
restrained for their
age and size.
- Always install forward o r rear-facing
child safety seats on the rear seat -even
with an Advanced A irbag System.
- If you must install a rearward-facing
child safety seat on the front passenger
seat because of exceptiona l circumstan­
ces and the
PASS ENG ER AIR BAG OFF
light does not appea r and stay on, imme­
diate ly install the rear-facing child safety
seat in a rear seat ing pos ition and have
the airbag system inspe cted by your au­
thori zed A udi dealer.
- A tight tether or other s trap on a rea r­
ward-facing child restraint att ached to
the front passenger seat can p ut too
m uch p ressure on the weight-sensing
mat in the seat and registe r more weight
than is actually on the seat. The heavier
weight registered can make the system
work as though an adult were on the seat
and deploy the Advanced Airbag when it
must be suppressed causing ser ious or
even fata l injury to t he ch ild.
- If, i n exceptiona l circumstances, you
m ust ins tall a forward-fac ing ch ild re­
straint o n the front passenger seat, al­
ways move the sea t in to its rearmos t po­
sition in the seat's fore and aft adjust­
ment range, as fa r away from the airbag
as possible. The backrest must be adjust­
ed to an upright pos ition. Make sure that
the
PASSENGER AIR BAG OFF light
comes on and stays on all the time when­
ever the ignit ion is switched on.
A WARNING
--
- If the PASSENGER AIR BAG OFF light
does not go out when an ad ult is sitting
on the front passenger seat after taking
the steps descr ibed above, make su re the
ad ult is properly seated a nd restra ined at
one o f the rea r seat ing pos itions.
- Have the airbag system inspected by
your author ized Audi dealer befo re tr ans­
port ing anyone on the front passenger
seat.
...

than 20 lbs. (9 kg) up to 40 lbs. (18 kg) must
always be properly restrained in a child safety
seat certified for their size and weight
c:> fig. 205 and c:> fig. 206.
The airbag on the passenger side makes the
front seat a potentially dangerous place for a
child to ride. The front seat is not the safest
place for a child in a forward-facing child safe­
ty seat.
It is a very dangerous place for an in­
fant or a larger child in a rearward -facing seat .
.,&. WARNING
Not using a child safety seat, using the
wrong child safety seat or improperly in­
stalling a child restraint increases the risk
of serious personal injury and death in a
collision or other emergency situation.
- Children on the front seat of any car,
even with Advanced Airbags, can be seri­
ously injured or even killed when an air­
bag inflates. A child in a rearward-facing
child safety seat installed on the front
passenger seat will be seriously injured
and can be killed if the front airbag in­
flates -even with an Advanced Airbag
System.
- The inflating airbag will hit the child
safety seat or infant carrier with great
force and will smash the child safety seat
and child against the backrest, center
armrest, door or roof.
- Always install rear-facing child safety
seats on the rear seat.
- If you must install a rearward facing
child safety seat on the front passenger
seat because of exceptional circumstan­
ces and the
PASSENGER AIR BAG OFF
light does not come on and stay on, im­
mediately install the rear-facing child
safety seat in a rear seating position and
have the airbag system inspected by your
Audi dealer.
- The rear side of the child safety seat
should be positioned as close as possible
to the backrest on the vehicle seat. Ad­
just or remove the rear seat head re­ straint if it is difficult to install the child
Child Safety 207
seat with the head restraint in place
c:> page 77. Install the head restraint
again immediately once the child seat is
removed . Driving without head restraints
or with head restraints that are not prop­
erly adjusted increases the risk of serious
or fatal neck injury dramatically.
- Always read and heed all WARNINGS
whenever using a child restrained in ave­
hicle is being used
c:> page 170, Safety
belts,
c:> page 179, Airbag system and
c:> page 200, Important things to know.
.,&. WARNING
If exceptional circumstances require the
use of a forward-facing child restraint on
the front passenger's seat, the child's safe­
ty and well-being require that the follow­
ing special precautions be taken:
- Make sure the forward-facing seat has
been designed and certified by its manu­
facturer for use on a front seat with a
passenger front and side airbag .
-Always follow the manufacturer's in­
structions provided with the child safety
seat or infant carrier .
- Always move the front passenger seat in­
to the rearmost position of the passen­
ger seat's fore and aft adjustment range,
and as far away from the airbag as possi­
ble before installing the child restraint.
- Always make sure that nothing prevents
the front passenger's seat from being
moved to the rearmost position in its
fore and aft adjustment range.
- Always make sure the backrest is in an
upright position.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched on.
- If the light does not stay on, perform the
checks
c:> page 190, Monitoring the Ad­
vanced Airbag System.
- Take the child restraint off the front pas-
-
senger seat and install it properly at one ~
•
•

because of exceptional circumstances, be
properly restrained and as far away from the
airbag as poss ib le . By keep ing room between
the child's body and the front of the passen­
ger compartment, the airbag can inflate com­
p letely and provide supplemental protection
i n certa in frontal collis ions .
A WARNING
Not using a booster seat, us ing the boos­
ter seat imprope rly, i ncorrect ly ins tall ing a
booste r seat or using the vehicle safety
bel t improperly increases the risk of seri­
ous personal injury and death in a collision
or other emergency s ituation. To help re­
duce the risk of ser ious persona l injury
and/or death:
- The shoulder be lt must lie as close to the
center of the child's co llar bone as possi­
ble and must lie flat and snug on the up­
per body. It must never lie across the
throat or neck. The lap belt must lie
across the pelvis and never across the
stoma ch or abdomen. Make su re the bel t
lies flat and snug. P ull on the be lt to
t igh ten i f ne cessary.
- Failure to properly route safety belts
over a ch ild' s body will cause severe inju­
ries in an a cciden t or o ther emergency
situation ¢
page 170.
-The rea r side of the child s afety se at
sho uld be positioned as close as possible
to the back rest on the ve hicle seat. A d­
just or remove the rear seat head re­
straint if it is difficult to install t he child
seat with the head restrai nt in place
¢
page 77. Install the head restra int
agai n immed iate ly once the child sea t is
removed. Driving w ithout head rest raints
o r with head res traints tha t are no t prop­
e rl y adju sted incre ases the risk of ser ious
o r f atal neck injury dramat ica lly.
- Children on the front seat of any car,
even with Advanced A irb ags, can be seri­
o usly inju red or even killed when an a ir­
bag inf lates .
- Never le t a child st and or knee l on any
sea t, for examp le the front seat.
-
Child Sa fet y 209
-Never let a chi ld r ide in the cargo area of
your veh icle.
- Always remember t hat a c hild leaning
forward, sitting sideways or out of posi­
tion in any way d uring an accident can be
struck by a dep loying a irbag. This will re­
sult in ser ious personal inju ry or death .
- If you must install a booster seat on the
front passenger seat because of excep­
tional ci rcumstances the
PASSENGER
AIR BAG OFF
li ght m ust come o n and
s tay on, w henever the ign ition is switc h­
ed on.
- If the
PASSENGER AIR BAG OFF li ght
does not come on and stay on, pe rform
the c heck s descr ibed¢
page 190, Moni­
toring the Advanced Airbag System .
- Take the chi ld restraint off the fron t pas­
senger sea t and inst all it prope rly at one
of the rear sea t positions if the
PASSEN­
GER AIR BAG OFF
li ght does not stay on
whenever the ignit ion is switched on .
-A lways read an d heed a ll WAR NIN GS
wheneve r using a chi ld restrained in ave ­
hicle is being used
¢ page 170, Safety
belts,
¢ page 179, Airbag system and
¢ page 200, Important things to know.
Installing a child safety
seat
Securing a child safety seat using a
safety belt
Safety belts for the rear seats and the front
passenger con be locked with the convertible locking retractor to properly secure child
safety seats.
The safety belts emergency locking retractors
for the rear seats safety belts and for the
front passenger's seat safety be lt have a co n­
vertib le locking retractor for child rest raints.
T he safety belt must be locked so that be lt
webb ing cannot unreel. The retractor can be
activated to lo ck the safe ty belt and prevent
t h e safety be lt webbing from looseni ng up
during norma l dr iving . A chi ld safety seat can
o nl y be properly installed when the safety belt.,.. •
•

214 Child Safety
Attachment locator markers for lower
anchorages
The lower anchorage locations in the second
row of seats are indic ated by the attachment
locator marke rs of the lower anchorage brack­
ets
¢ fig. 209. Remove the covers to access
the lower anchorage brackets . C ircular locator
buttons on the th ird row of seats* ind icate the
l ower anchorage locations on the third row of
seats¢
fig . 210.
Lower anchorages
The lower anchorage attachment points are
located between the rear seatback and rear
seat cushion ¢
fig. 209 or¢ fig. 210 .
Lower anchorages secure the child restraint in
the seat without using the vehicle's safety
belts. Anchorages prov ide a secure and easy­
to-use attachment and m inimize the possibili­
ty of improper chi ld restraint installation.
All child restra ints manufactured after Sep­
tember 1,
2002, must have lower anchorage
attachments for the
LATCH system.
Remember that the lower anchorage points
are only intended for installation and attach­
ment of child restraints specifically certified
for use w ith
LATCH lower anchorages . Child
restraints that are not equipped with the low­
e r anchorage attachments can still be instal­
l ed in compliance w ith the child restraint
manufacturer's instructions on using vehicle
safety belts.
_&. WARNING
Improper use of LATCH lower anchorages
can cause serious personal injury in an ac­
cident.
- Always carefully fo llow the child re­
straints manufacturer's instruct ions for
proper installation of the child restraint
and proper use of the lower anchorages
or safety belts in your vehicle.
- Never secure o r attach any luggage or
other items to the
LATCH lower ancho­
rages . -
Always read and heed the important in·
formation about child restraints in this
chapter and WARNINGS ¢
page 200,
Child Safety.
Guidance fixtures for lower anchorages
App lies to vehicles: wit h third row seating
Special guidance fixtures increase the conven­
ience of the lower anchorages and are availa­
ble from your authori zed Audi dealer.
Fig . 211 Thir d row of seat s: in sta lling the guidance fix·
t u res
Fig. 212 Close-up : fitting the guida nce f ixture over t he
lowe r anchorage b racket
T he lower anchorage attachment poi nts are
located on the third row of seats between the
seatback and the seat cushion. Special guid­
ance fixtures increase the conven ience of the
lower anchorages and help protect the seat
material from possible damage when insta l­
ling child restraints.
Installing the guidance fixtures
" Push down on the seat cushion so that the
lower anchorages are visible.
" Hold the guidance fixture with the part
number facing downward and push it in the
direction of the arrow onto the anchorage
¢ fig. 212 .

.. Make sure that each of the two guidance fix ­
tures per seat snaps into p lace.
Rem oving the guidance fi xture s
.. Remove the child restrai nt according the
child restra int manufacturer's instruct ions .
.. Push down on the seat cushion so that the
lower anchorages are visib le .
.. Pull
off the guida nee fix t u res from the low­
er anchorages.
.,. Always remove the guidance fixtures and
keep them in a safe place when not in use.
You may find it easier to install child re­
straints equipped with hooks attached to
straps without the guidance f ixtures in place.
If this is the case, remove the guidance fix­
tures by pull ing them
off the anchorages .
H owever, the guidance fixtures can he lp you
to locate the
LATCH anchorages.
_& WARNING
Improper use of tether anchorages or low­
er anchorages can cause serious personal
injury in a crash .
- Always carefully follow the ch ild re­
straint manufacturer 's instruct ions for
proper installation and use of child re­
straint systems.
- Never use the
LATCH or tether anchorag ­
es to attach safety belts o r other kinds of
occupant restraints .
- Child restraint tether attachments and
lower attachments are only designed to
secure a child restraint that has been equipped to use these anchorages.
- Tether anchorages and lower anchorages
are designed to withstand only those
loads imposed by correctly fitted chi ld
restraints. Under no circumsta nces can
they be used safely for adu lt or chi ld
safety belts o r harnesses .
- Never mount more than one ch ild re­
st raint to a sing le tether or to a lower an­
cho rage point. Attach ing two ch ild re­
st raints to a single anchorage point can
ca use the anchorage to fail and cause se­
rious persona l injury in a crash .
Child Safety 215
(D Note
-Remove the g uidance fixtures before
folding the rear seatback to prevent damaging the seat cushion .
- If you leave the guidance f ixtures instal­
led for several days , they could leave a
mark on the upholstery on the seat cush­
ion and backrest in the area that the
guidance fixtures were installed . The up ­
holstery would also be permanently
st retched a round the guidance fixtures.
T hi s app lies especia lly to leather seats.
Installing a child restraint with LATCH
lower anchorages
Whenever you install a child restraint always
follow the child restraint manufacturer's in ­
structions.
F ig. 213 Lowe r anc horages : prope r mount ing
Mountin g
.. Make sure the seatback of the rear seat
bench is in t he upright position and securely
latched in place .
.. Attach both hook-on co nnectors with the
spring catch release on the child safety seat
onto the LATCH lower anchorage so that the
connecto rs lock into place
~ fig. 213.
.. Pull on the connector attachments to make
sure they are properly attached to the LATCH
lower ancho rage .
.. Pull straps tight fo llowing the child re­
straint manufacturer's instructions.
Relea sing
.. Loosen the tension on the straps following
the child restraint manufact urer's instruc ­
tions .

_& WARNING
Improper installation of child restraints
w ill increase the risk of injury and death in
a crash .
- Always follow the instructions prov ided
by the manufacturer of the ch ild re­
st raint you intend to install in your Audi.
- Improper use of ch ild restraint anchors
(including tether anchors) can lead to in­
jury in a co llision. The anchors are de­
signed to withstand only those loads im­
posed by correct ly fi tted ch ild restraints.
- Never mount two child restrai nt systems
on one LA TCH lowe r ancho r po int.
- Never attach two child restraint systems
to one tethe r strap or te ther anchorage.
- Never attach a tether st rap to a tie-down
hook in the luggage compartment.
- Never use ch ild restra int tether ancho­
rages to secur e safety belts o r other
k inds of o ccupant rest ra ints.
- Never secure o r attach any l uggage or
other items to the LATCH lowe r ancho­
rages or to t he tethe r ancho rs.
- If a tether o r othe r strap is used to at­
ta ch a child rest raint to the front passen­
ger seat, make sure that it is not so
t ight, th at it c auses the weigh t-sensing
mat to measure mo re weig ht than is ac ­
t u ally on the seat.
- T he heav ier we ig ht reg iste red can make
the Advanced Airbag System work as
though an ad ult were on the seat and de­
ploy the Advanced Airbag w hen it must
be suppressed causing serious or even
fatal injury to the child .
- If you must install a rearward facing child safety seat on the front passenger
seat beca use of exceptional circ umstan­
ces and the
PASSENGER AIR BAG OFF
light does not come on and stay on, im­
med iate ly install the rear -facing child
sa fety seat in a rear seating posi tion and
have the a irbag sys tem inspec ted by you r
Audi dealer .
Child Safety 21 7
Installing the upper tether strap on the
anchorage
Fig . 21 6 Tet her s trap: prope r rout ing a nd m ounti ng
Fi g. 217 Tet her st rap fo r seco nd row se ats: prope r
rou ting and moun tin g
Installing the tether strap
... Release or deploy the tether strap on the
child res traint accord ing to the child re ­
st raint manufacture r's ins tructions .
... Guide the upper tether strap
und er the rear
head restraint and into the rear ca rgo area
(raise the head restraint if necessary) .
... Fo r the second row o f seats: Pull the floor­
ing back, in order to reach the anchor brack­
et
c:::> fig. 217 .
... For the third row of seats :* Remove the
plastic cover cap with a screw drive r, in orde r
t o reach the anchor bracket
c:::> page 216,
fig . 215.
... Slide the tether s trap hoo k over the anchor
bracket .
... Pull on the tether strap hook so that the
spring catch of the hook engages .
.,. Tighten the tether strap firmly fo llow ing
the child restra int manufacturer's instruc­
tions.
.,. For the second row of seats: Push the floor­
ing forward into place again.

The MMI control console should be cleaned
with a brush first so that no dirt is trapped be ­
tween the buttons and the housing . We rec­
ommend giv ing the MMI control console a fi­
nal w ipe with a cloth mo istened with water
and d ish washing detergent.
Q;) Note
To prevent damage, make sure that no flu­
id ever gets into the MMI control console .
Aluminum trim
Use only neutr al- pH products to remove spots
and depos its from alum inum surfaces.
C hr ome ca re products and alkaline cleaners
will attack alum in um s urfaces and can dam­
age them ove r time.
& WARNING
Always read and heed a ll WARNINGS and
other information
¢ page 239 .
Fabrics and fabric coverings
Fabrics and fabric coverings (e .g. seats, door
trim panels, etc.) should be cleaned at regu lar
intervals with a vacuum cleaner . Th is removes
surface dirt particles which could become em­ bedded in the fabr ic through use. Steam
cleaners should not be used, because the
steam tends to push the dirt deeper into the
fabric and lock it there.
Norm al cleaning
Generally, we recommend using a soft sponge
or a lint-free microfiber cloth to the clean fab­
ric. Brushes should only be used for carpets
a nd floor mats, since other fabric surfaces
could be harmed by b rushes.
Normal surface sta ins can be cleaned using a
commercia lly available foam cleaner . Spread
the foam on the surface of the fab ric with a
soft sponge and work it in gently. Do not sat u­
r ate the fabric. Then pat the foam dry using
absorbent, dry cloths (e .g. microfiber cloth)
and vacuum it after it has dried comp lete ly.
Cleaning and protec tion 245
Cl ean ing sta in s
Stains caused by beverages (e.g . coffee, fruit
juice, etc.) can be treated with a mild deter ­
gent solution. Apply the detergent sol ution
with a sponge. In the case of stubborn stains, a detergent paste can be applied directly to
the s tain and worked into the fabric . After­
wards, use copious amounts of clean water to
remove the rema ining detergent . Apply the
water with a damp cloth or sponge and pat
the fabric dry with an abso rbent, dry cloth.
Stains from chocolate or makeup should have detergent paste (e .g . ox -gall soap) rubbed in ­
to them . Afterwards, remove the soap with
water (damp sponge).
Alcohol can be used to treat stains from
grease, o il, lipstick or a ballpoint pen . Melted
grease or dye must be patted off using ab­
sorbent mater ial. It may be necessa ry to re­
treat the areas with detergent paste and wa­
te r.
In the case of general soiling of the uphols­
tery and cover material, we recommend hir ing
a specia list that has the eq uipment to clean
the seat cove rs and othe r fabr ic surfaces by
shampooing and spray extraction.
A WARNING
A lways read and heed all WARNINGS and
the information
¢ page 239.
(D Tips
Open Ve lcro fas teners on yo ur cl othing can
damage the seat cover . Please make sure
that Ve lcro fasteners are closed .
Plastic parts and instrument panel
Always use a clean cloth moistened in clear
water to clean these areas. For persistent d irt
use an Aud i approved
s olvent-fre e plastic
clea ner/protectant . .,.. •
•