Instruments and warning/indicator lights 17
9::;r: Engine oil pressure malfunction
The red engine oil pressure warning symbol
requires immediate service or repair . Driving
with a Low-oil-pressure indication is Likely to
inflict severe damage to the engine .
• Switch off engine and check oil level
If the indicator light t urns on the message ap
pears, the oil press ure is too low.
~ P ull off the road.
~ Stop t he ve hicle .
~ Turn off the engine.
~ Check the engine oil level¢ page 224 .
~ If the engi ne oil leve l is too low, add engine
o il ¢
page 225. M ake sure that the oil p res
s ur e warning symbol. appears no longer
in t he d is pl ay befo re y ou start driving aga in.
~ If the engine oil leve l is cor re ct an d the ind i
c a tor lig ht still tur ns o n, tur n t he eng ine
off
and do not contin ue d riving . Seek professio
nal assistance.
(D Tips
- The engine oil pressure symbol. is
not an indicator for a low engine oil lev
el. Do not rely on it. Instead, check the
oil level in your engine at regular inter
vals, preferably each time you refuel,
and always before going on a long trip.
- The yellow oil level warning indication
II requires oil refill or workshop serv
ice without delay. Do not wait until the
red oil pressure warning. starts to
flash before you respond to the low oil level warning
l!I. By then, your engine
may already have suffered seriou s dam
age .
~ . Engine oil level
• WARNING: Please add oil immediately
When t he sy mbo l and the dr iver message a p
pea r, the oil has to be reple nished r ight now
¢page 222.
If the indicator lig ht and th e message ap pear,
a d d engine o il i mm edi ate ly
¢page 225.
II Add oil , max . x qt (l). You may continue
driving
Whe n the symbol and the d river message ap
pear, add the amoun t of oil appear ing in the
display at the nex t oppo rtuni ty ¢
page 222.
® -Steering column lock
• Do not drive vehicle: Steering defective
If th e indic ator li ght turns on and the mes
sa ge appe ars, there is an e lectroni c steering
column lock malf unct ion . You cannot switch
the ignit ion on.
D o
not tow yo ur vehicle beca us e it cann ot b e
s tee red. See k profession al assistance .
!'J!I Steering lock : system fault . Please con
tact dealer
If the indicato r light turns on and the mes
sage appea rs , t here is an e lectronic stee ring
column lock malfunct io n .
Drive to your auth orized A udi dealer immedi
ately to hav e th e m alfunction corr ect ed .
A WARNING -
Your vehicle m ust not b e tow ed in t he
eve nt of a ma lfunction in the elec tronic
st eer ing col umn lo ck b eca use i t cann ot be
s teere d du e to the lock ed s tee ring. If it is
towe d wit h the steer ing lo cke d, there is
the r isk o f an acci dent.
© -Engine start system
• Engine start system fault. Please con
tact dealer
If the indica to r li ght tur ns on and the mes
sage a ppea rs, do
not switch the ignition off
because you may not be ab le to sw itch it on
again.
D rive to your autho rized A udi de aler imme di
ate ly to have the ma lfunction corrected.
• Engine start system fault . Plea se con
tact dealer
18 Instruments and warning/indicator lights
If the indicator light turns on and the mes
sage appears, there is a ma lfunction in the en
g ine start system.
Drive to your authorized Aud i dealer immedi
ate ly to have the malfunction cor rected .
0 Air suspension
• Air suspension: system fault. Can contin
ue slowly with max. 35 mph .
There is a malfunction that can result in re
stricted driving stability .
Ca refully drive at a maximum speed of 35
mph
(60 km/h) to your authorized Audi dealer
or qualified workshop to have the malfunction
corrected .
• Air suspension: service mode. Vehicle
can only be moved with restrictions
Carefully drive to your authorized Audi dealer
or qualified workshop immediately to have
the service mode deactivated.
Ill Air suspension fault
There is a system ma lfunction that can result
in restr icted driving stability or reduced
ground clearance.
Drive to your authorized Audi dea ler immedi
ate ly to have the malfunction corrected.
IIJ Air suspension: vehicle too low. Ground
clearance reduced
The ground clea rance is ve ry low due to a sys
tem malfunct ion. Wait until the air suspen
sion system has restored normal ground clear
ance . Otherwise, conditions such as an uneven
road surface can lead to ve hicle damage.
~/ !f Safety systems
The fl (USA models) ;BI (Canada models) in
d icator light monitors the safety systems e.g.
a ir bags, pretensioners and illum inates for a
few seconds each time you switch the ignition
on .
If the
I (USA models) ;BI (Canada models)
indicator light does not go out, or if it illumi- nates while you are driving, or if it starts to
blink,
then there is a malfunction somewhere
in the system.
If the light does not illuminate
when you switch the ign it ion on, th is also
means there is a malfunct ion.
A WARNING '"--
If you have a ma lfunction in the safety sys-
tems, contact your authorized Audi dea ler
imme diately. Otherwise the safety sys
tems may not work properly in an acci
dent.
fJJ [}, Electronic Stability Control (ESC)
This warning/indicator light monitors the
Electronic Stability Control.
When you switch the ignition on, the indicator
light
G1 turns on briefly to check the function.
If the
J.iJ ind icator lamp blinks wh ile driving,
the ESC or ASR (Anti-Slip Regulation) is active
ly regulating.
If
the DJ ind icator lamp illuminates, the sys·
tern has switched the ESC off.
If the indicator light fi turns on, the ESC was
switched to ESC sport mode with the button
[!] c::, page 187. If this is case, you can reacti
vate the ESC by switching the ignition off and
then on aga in. The warning/indicator light
should go out to show that the system is fully
functional again .
Stability program and ABS fault! See own
er 's manual
If the indicator light DJ and the ABS indicator
li ght
m (USA models) ;II] (Canada models)
turn on and the message appears, there is a malfunction in the ABS system or electronic
differential lock. Th is also interrupts the ESC.
The brakes still funct ion wit h their normal
power, but ABS is not active .
Drive to your authorized Audi dealer immedi
ately to have the malfunction corrected .
If the battery terminals were disconnected
and re-connected, the vehicle was jump start-
ed or the battery is very weak, the ESC sensor .,,.
Instruments and warning/indicator lights 21
Bu Fuel level indicator
II Please refuel
If the indicator light turns on for the first
time and the message appears, there are
about 4 ga llons (15 liters) of fuel left in the
tank . T im e to refuel
<=>page 216.
II Tank system malfunction! Contact dealer
If the indicator light turns on and th is mes
sage appears, there is a malfunction in the
tank system.
Drive to your authorized Audi dea ler immedi
ately to have the malfunction corrected .
co Windshield washer fluid level
II Please refill washer fluid
If the symbol illuminates, add windshield
washer fluid to the washer system/headlight
washer system* <=>
page 234.
4I:> Windshield wipers
!I Windshield wiper defective
There is a malfunction with the windshield
wipers.
Drive to your authorized Aud i dealer immedi
ately to have the mal function cor rected .
~!}0 10$ Defective light bulb warning
I-If the indicator light turns on, a bulb has
fa iled. The message indicates the location of
the bulb.
II-if a fog lamp* has failed, the ind icator
light t urns on to indicate the location on the
vehicle.
[ti-if a rea r fog lamp has failed, the ind icator
light turns on to indicate the location on the
vehicle .
Vehicle lights: malfunction
If the message appears, there is a malfunc
tion in the headlights or light switch. Drive to
your authorized A udi dealer immedi
ate ly to have the ma lfunction corrected.
A WARNING
- Light bulbs are pressurized and could ex
plode w hile they are being changed ca us
ing serious personal injury.
- Work with due care when hand ling the
high-voltage sect ion of gas discharge
(xenon) lights. Failure to do so could re
sult in death or serious injury.
(1) Tips
Have the bu lb replaced or the connection
repaired by your authorized Audi Service
department.
i.lD Headlight range control
II Headlight range control: defective!
If the symbol illuminates, the headlight range
control is no longer work ing properly. Have
the system checked and repaired at your Audi
dealer .
~0 Adaptive Light
Applies to veh icles: w it h Adaptive light
ml Audi adaptive light: system fault
If the indicator light turns on and this mes
sage appears, there is a malfunct ion in the
adaptive light system. The headlights st ill
function.
Go to an authorized dealersh ip to have the
headlights or the control unit for the Adaptive
Light repa ired .
@ Light/rain sensor
!I Automatic headlights/automati c wipers:
system fault
If the indicato r light turns on and this mes
sage appears, the light/rain sensor is not
funct io nin g correctly.
For safety reasons the low beams are turned
on permanently with the switch in
AUTO . liJI,
Instrument s and warning /indicator lights 23
Driver information
display
Overview
Fig. 4 Driv er in formation system in t he in strum en t
cl uster
Fig . 5 D isplay: e xample of th e informa tion line
The driver information system contains infor
mation
® that is displayed on tabs ®
c::> fig. 4. The follow ing content is possibl e de
pending on vehicle equipment:
®
Tab
1
2
---
®
Content
Vehicle functions:
On-board computer <=;>page 24
Digital speedometer
Cruise control*
c::> page 85
Adaptive cru ise control and Audi
braking guard*
c::>page 87
Audi lane assist* c::> page 96
Display darkened
Indicator lights and messages
Warning when a door, the hood or
the rear lid is not closed
c::> page 26
Service interval display¢
page 25
Speed warning system ¢ page 85
--
® ®
Tab Content
3 Night vision assistant* c::> page 106
4 Audio/video
s Telephone*
6 Navigation*
The second and th ird tabs are only v isible if at
least one indicator light or message is shown
o r i f that system is switched on .
The status line © is located in the bottom
part of the d isplay
c::> fig . 4. It displays the ex
terior temperature , time , selecto r lever posi
tion, trip odometer and odometer.
I
For some vehicle functions, you can access the
trip information from the temporary memory
r::!;> page 24 i n the line (D c::> fig. 5.
& WARNING ,.______ -
- Never re ly exclusively on the outside
temperature display to determine if a
road surface is icy or not. Keep in mind
that road surfaces, especia lly bridges
and overpasses, could be ice covered and
slippery even at an outside temperature
above 41 °F ( +S
0
() .
-Always remember, even if the "snow
flake" symbol (ice warning) does not ap pear in the display, black ice could be on
the road .
- Always reduce your speed and drive with
special care in cold weather conditions
when the chance of encountering icy road surfaces increases.
(i) Tips
-At temperatures below 14 °F (+ S 0
() a
snowf lake symbol appears ahead of the
temperature display .
It is intended to re
mind the driver to pay special attention
to
ice on the road c::> &. If the vehicle is
stationary, or if you are driving at a very
low speed, the temperature shown in the
display might be slightly higher than the
actual outside temperature. This is
Instruments and warning/indicator lights 25
For some vehicle functions, you can access the
trip information from the temporary memory
in the line
(I) c:;; page 23, fig. 5.
@ Tips
- All stored values will be lost if the vehi
cle battery is disconnected.
- Fuel consumptions (average and cur
rent), range and speed are displayed in
metric units on Canadian models.
Odometer
Fig. 8 Instrument cluster Odometer and reset b utto n
The odometer shows you how many miles
(kilometers) you have driven. You can switch
th e display from miles to kilometers and vice
versa via the MMI.
Upper odometer
The trip odometer shows the distance driven
since it was last reset.
It can be used to meas
ure short distances. The last digit indicates 1/10 of a mile (100 meters).
You can reset the trip odometer to zero by
pressing the Reset button~-
Lower odometer
The lower odometer shows the total number
of miles (kilometers) driven .
Malfunction message
If there is a malfunction in the instrument
cluster,
DEF will appear in the trip odometer
display area. Contact your authorized Audi
dealer to have the problem corrected .
Time and date display
...
I~
Fig. 9 Cente r console : analog clock
The date and time are shown in the instru
ment cluster display
c:;; page 23, fig. 4. There
is also an analog clock in the center console
¢fig . 9 .
:r
~
When you open the driver's door, the date and
time appear in the instrument cluster display
for 30 seconds. When the ignition is switched
on, the time is always displayed in the status
line © regardless of the current display.
You can set the time on both clocks and the
date display in the MMI. Refer to the MMI
owner's manual for instructions.
Service interval display
The service interval display reminds you when
your next service is due .
Fig. 10 Instrument cluster: Serv ice inte rval disp lay
The schedule for the next oil change or inspec
tion is calculated automatically and displayed
accordingly. The display works in two stages:
Service reminder
30 days before the next service is due, a serv
ice reminder appears in the display when you
switch the ignition on
¢fig. 10. ..,.
26 Instruments and warning /indicator lights
After abo ut 5 seconds the display sw itches
back to normal. The distance and time re
maining are updated eac h time the ignition is
switched on until the date due for service is
reached .
Service due
When the due date for service is reached , the
message
Serv ice due! appears in the instr u
ment cluster immediately after you switch the
ignit io n on . Additionally, a warning tone
sounds . After about
5 seconds the display
sw itches back to no rmal.
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the MMI d isplay by select ing
the service interva l display in the car menu .
Select the
!CAR ! function button> Car sys
tems
co ntrol button > Servicing & checks >
Service interval disp lays.
Re setting the service interval display
Your author ized Audi dealer w ill reset the cor
responding service sched ule after performing
the app rop riate se rv ice on you r vehicle . You
a lso have the possibili ty to reset the o il
change sched ule after having performed an
oil c hange a ccor ding to Audi s pecifications.
Selec t the
I CAR I func tion button > Car sys
tems
c on trol b utt on > Servicing & checks >
Service interval displays > Reset oil change
inte rval.
{[) Note
If you disconnec t the b attery termi nals, no
calc ulations can be made for the serv ice
interva l display during this t ime and no
service rem inder w ill appea r. Remembe r
that obse rv in g the prope r se rv ice interva ls
is vitally impo rtant to extend ing the life of
your v eh icle, part icu larly the eng ine, and
main taini ng its va lue . Ev en i f th e m ileage
driv en is low, th e maximum per iod o f one
yea r from o ne se rvi ce to the nex t mus t not
be e xcee ded.
(D Tips
- Do not reset the display betwee n oil
c h anges, otherwise the d isp lay w ill be in
co rrect.
- Th e info rmation in the Se rvice Remin der
remains stored even w hen t he vehicle
battery is disconnected.
Open door /hood /rear lid warning
F ig. 1 1 Display : doors and rea r lid open
Wi th the ig nition sw itched on, t he warn ing il
lu minates when at least
one doo r or th e hood
or the rear lid is not closed. The sym bo l also
shows you
which d oor(s) or lid is not closed.
In the illustration
r:!> fig. 11 it is the driver's
doo randt he leftrea rdoo ~
On-Board Diagnostic
system (OBD)
Malfunction Ind icator Lamp (MIL )
The Ma lf u nction Indicator Lam p (M IL) f-4 in
t h e instr ume nt cluster is part of t he On -Board
Diagnostic (OBD
II) system .
T he wa rn ing /indic ator lig ht ill uminates when
the ignitio n is switched on and goes ou t after
t h e engine sta rts and t he id le has sta bilized.
This ind icates that the MIL is working proper
ly.
If the light does not go out afte r the e ngine
is starte d, or illumi nates w hile you are driv
i ng, a mal function may exist in the engine sys
tem . If t he light illum inates, t he catalytic con-
verter could be damaged .
IIJ,-
Instruments and warning/indicator lights 2 7
Continue driving with reduced power (avoid
ing sustained high speeds and/or rapid accel
erat ions) and have the condition corrected.
Contact your author iz ed Audi dealer.
If the light ill uminates, the electronic speed
limiter may also be ma lfunctioning . For more
information ¢
page 2 7, Electronic speed
limiter .
An improperly closed fuel fi ller cap may also
cause the MIL light to ill uminate ¢
page 217.
On-Board Diagnostics
Fig. 12 Loca tion of Data Li nk Connector (DLC)
On-Board Diagnostics monitors the compo
nents of yo ur emission control system. Each
mon itored component in your engine system
has been assigned a code. In case of a ma l
function, the component will be identified and the fault stored as a code in the contro l
module memory.
The MIL light may a lso illuminate if there is a
l eak in the on-board fue l vapor recovery sys
tem. If the light illuminates after a ref uelling,
stop the veh icle and make sure the fue l filler
cap is properly closed ¢
page 217.
In order to make an accurate diagnosis, the
stored data can only be displayed using spe
cial diagnostic equipment (gener ic scan tool
for OBD).
In order to connect the special diagnostic
eq uipment, push the plug into the Data Link
Connector (DLC). The DLC is located to the right of the hood release¢
fig. 12.
Your authorized Audi dea ler or a qualified
service station can interpret the code and per
form the necessary repair.
A WARNING
Do not use the diagnostic connector for
personal use. Incorrect usage can cause
malfunctions, wh ich can increase the risk
of a collision!
Electronic speed limiter
-
Your vehicle may be factory equipped w ith
t ir es that are rated fo r a maximum speed of
130 mph (210 km/h). This is less than the
maximum speed of your vehicle . To reduce the
risk of sudden tire fai lure and loss of control if
the vehicle is operated at excessive speeds,
your vehicle a lso has an e lectronic speed limit
er . The e lectronic speed limiter prevents your
vehicle from going faster than the tire speed rating . For more information ¢
page 246.
If the engine contro l unit receives faulty vehi
cle road speed signa ls, the Ma lfunction Indi·
cator Lamp (MIL)
fllllij w ill illuminate. If this
occurs, contact the nearest authorized Audi
dealer for assistance .
A WARNING
-
Always observe the posted speed limits
and adjust your speed to suit prevailing road, traffic and weather conditions. Never
drive your vehicle faster than the maxi
mum speed rating of the tires installed.
Tire service life
The service life of tires depends on a lot of
different things including proper installation
and balancing, correct tire pressure and driv
ing style.
F ig. 185 Tire tread: tread wea r ind ica tors (TWI)
f r-------~
{ \ .___ _____ ___,,
Fi g. 186 Rotat ing t ires fo r m ore even wea r
Tread Wear Indicator (TWI)
The origina l tires on your veh icle have
1/16 in ch (1.6 mm) high "wear ind icators"
c::> fig . 185 run ning across the tread. Depend
ing on the make, there will be six to eight of
them evenly p laced around the t ire . Marks on
the t ire s idewall (for example "TWI" or other
symbols) indicate the positions of the tread
wear ind icators . Worn t ires must be replaced.
Different fig ures may apply in other countries
c::> & .
Tir e pressure
Incorrect tire pressure causes premat ure wear
and can cause sudden tire blow-out . For th is
reason, tire pressure must be checked at least
once a month
c::> page 241.
Dri ving sty le
Driving fast around curves , heavy acceleration
and hard braking increase tire wear. Tires and wheels 245
Rotating tires for more even wear
For all four tires on your ve
hicl e to have the
same service life, we recommend that the
front and rear tires are rotated according to
the tire manufacturer 's suggested tire rota
tion inte rvals. Please remember the follow
ing :
- Tire rotation intervals may differ from the
veh icle service inte rva ls o utlined in your
Warranty & Maintenance booklet.
- The longer one tire is used in one location
on the vehicle, the more it wears at certain
points ; therefore, we recommend that you
follow the tire manufactu rer 's suggested
tire rotation intervals .
- Vehicles w ith front-wheel dr ive exper ience
more tread wear on the front wheels com
pared to all -wheel d rive (quattro ®).
- Please rotate tires as shown
c::> fig. 186.
-Extra care must be taken when rotat ing di-
rection-specific tires
c::> page 264 .
Wheel balancing
The wheels on new veh icles are balanced .
However, various situations during everyday
driving can cause them to become unba l
anced, resulting in vibrat ions you can usually
feel through the steer ing wheel.
Unbalanced wheels must be rebalanced to
avoid excessive wear on steering, s uspension
and t ires. A whee l must also be reba lanced
when a new tire is insta lled.
Inco rrect wheel alignment
Incorrect wheel alignment can cause exces
sive tire wear, impair ing the safety of the vehi
cle . If tires show excessive wear, have the
whee l alignment checked by an authori zed
Audi dealer or qualified workshop.
All Wh eel Driv e
Vehicles wi th quattro ® mus t always have tires
of the same size, construction and tread type. For details see
c::> page 191.