2012 AUDI A8 Neutral

110 Automatic Tran sm iss ion
• You may need to release the selector lever
l ock depending on which se lector lever posi ­
t ion is selected and which one you would
Like to select ¢
page 110, Selector lever
lock.
• To engage the nearest selector lever posi ­
t ion, move the selector lever forward/back
unti l you feel the first pressure point . The
selector lever will return to its original posi ­
t ion.
• To skip over one (or two) se lector lever posi­
tions, move the selector lever past the first
(and second) pressure point into the desired
pos it ion. The selector lever will return to its
origina l position.
For example, to move directly from the D se­
lector lever position to P when stopping the
vehicle, you can shift past the N and R selector lever positions.
S ele ctor l ever lock
The selector lever lock prevents you from se ­
lecting a position unintentionally, causing the
vehicle to roll. When engaging some selector lever positions, you must press the button on
the selector lever¢
fig. 116 and/or press the
brake pedal.
You must press the brake pedal to engage a
selector lever position when the engine is run­ n ing while the vehicle is stationary. The ar­
rows¢
fig. 117 indicate when you need to
press the button on the selector lever .
The selector lever does not lock if you sh ift
from D to R w ith in one second . Th is allows
you to "rock" the vehicle to free it when it is
stuck .
P- P ark
The whee ls are locked in th is position. Only
shift into park when the vehicle is stationary
¢ & .To engage the P selector lever position,
press the button on the selector lever and
shift into the P position .
You can only shift out of park when the eng ine
is running and you are press ing the brake ped­
al. Press the button on the selector lever to r
elease the parking lock and select the desired
selector lever position.
P engages automa tica lly when you sw itch the
engine off while D, Sor R is engaged o r in
manua l mode .
If you switch the eng ine off when N is engag­
ed, the transmiss ion remains in N for approxi­
mately 30 minutes and then Pis engaged .
You must use the emergency release proce­ dure to release the parking lock before towi ng
the vehicle
¢ page 113.
R- Reverse
The reverse gear is engaged in this posit ion .
Only select reverse when the vehicle is sta­
t ionary and the eng ine is running at id le speed
¢ & -To engage the R selector leve r pos ition,
press the button on the selector lever, press
the b rake pedal and move the selector lever
into the R position.
T he back-up lights turn on when you select
the R selector lever pos it ion wh ile the eng ine
. . 1s ru nning .
N -Neutral
The transm iss ion is in idle in this pos it ion . To
engage the N selector lever posit ion, press
the button on the selector lever and sh ift into
t h e N pos it ion.
If you switch the eng ine off when N is e ngag­
ed, the transmiss ion remains in N for approxi­
mately 30 minutes and then P is engaged .
You cannot se lect the N pos ition when the ig­
nition is sw itched off. When dr iv ing th rough
an automat ic car wash, first select the N posi­
t ion and then switch the engine off
¢page 204.
The veh icle cannot be locked when the selec­
tor lever is in the N position.
D - Dri ve
In this pos ition, the transmission sh ifts up
and down automatically depending on eng ine
load, veh icle speed and the dynamic shift pro -
gram (DSP) .
ll-

cloth or sponge. Use a clean, soft cloth to rub
dry .
Grease, tar or o il stains can be removed with a
clean cloth or sponge soaked w ith all-purpose
cleane r or with a solvent designed especially
to clean viny l.
Occasiona lly apply a colo rless v iny l or leather
prese rvat ive to reta in the mate rial's l uster
and pliability .
~ WARNING
Always read and heed a ll WARNINGS and
other information
r=; page 203.
Aluminum trim
Use only neutral -pH products to remove spots
and depos its from alum inum surfaces.
Chrome care products and alkaline cleaners
will attack alum inum su rfaces and can dam­
age them over time .
A WARNING
Always read and heed a ll WARNINGS and
other information
r=:; page 203.
Touch-up paint
Minor paint damages should be touched up
immediately.
.,. Use either a touch-up pa int stick or spray
paint to cover minor scratches and nicks .
Your Audi dealer has touch-up paint for minor scratches and stone chips. Scratches should
be touched up soon after they occu r to pre­
vent co rrosion .
If a spot starts to rust, however, a simple
touch-up job w ill not be enoug h. The affected
surface must be sanded smooth and coated
with an a nti-rust pr imer befo re the pa inted
finish ca n be restor ed .
The number for the original vehicle paint ca n
be found on the vehicle ident ificat ion labe l
r=;page276 .
Cleaning and protec tion 207
A WARNING
A lways read and heed all WARNINGS and
other information
r=:; page 203.
, Windows
Clear vision to all sides .
Clean all windows regularly to remove road
film and car was h wax buildup.
.. Remove snow from w indows using a b rush .
.,. Use a p las tic ice s craper to remove ice from
windows and mirrors.
.. Remove other residue on the windows with
a spray-on g lass cleaner.
.. Wipe the windows dry with a clean piece of
cloth or kitchen paper towel.
The best way to remove snow from windows
and mirrors is to use a brush. Use a non-abra­
s ive
plastic ice scraper -better still, a spray
deicer - to remove
ice from w indows and mir­
ro rs .
Oil, grease or silicone residue can be removed
with
glass cleane r or silicone remo ve r. How­
ever, wax res idue requires the use of a spec ial­
ly formula ted so lvent . Please contact your Au­
di dealer for adv ice on safe products for wax
r emoval.
Windows should also be cleaned on the inside
at regu lar intervals .
Never dry windows with the same chamo is
that you use to dry painted surfaces. Wax resi­ due on the chamois can impa ir v is io n through
the windows .
A WARNING
-Always rea d and heed a ll WAR NINGS and
other info rmation
¢ page 203.
- The windsh ield must not be treated w ith
wate r-repellent mate rials. They can in­
crease glare unde r poo r vis ibility condi­
tion s such as wetness, d arkness, or when
the s un is low on the hori zon . In addi ­
tion, they can ca use the windshield w ip-
ers to chatter. ""'
•
•

substance use d for u ndercoating cou ld
overheat an d cause a fire.
- Always read and heed all WARNINGS and
other information
¢ page 203.
Exhaust tail pipes
Road sa lt and other corros ive materials will
damage the mater ial in the exhaust tail p ipes
if they are not cleaned regu larly . Do not clean
the ta il p ipes with wheel cleaner, paint polish,
chrome polish or othe r abrasive cleaners .
C lean the tail p ipes with ca r ca re products
that are s uita ble for stain less stee l.
Your authorized Audi dealer can provide clean­ i ng p rod ucts that have been tested and ap­
p roved fo r your vehicle.
Care of interior
Infotainment components
The MMI/RSE* disp lay may be cleaned with a
soft cloth and commercially-ava ilable "LCD
cleaner" . The cloth should be coated light ly
when the clean ing solution when cleani ng the
d isplay.
The MMI/RSE* contro ls must be cleaned first
with a brush so that dirt does not enter the
un it o r enter between the buttons and the
h ousing. Then w iping the controls with a clot h
dampened wi th d ish dete rgent and water is
recommended.
(D Note
To preve nt sc ratches, only clean the dis­
p lay when it is d ry.
- To p reven t damage, ma ke s ure fluids do
not enter the cont rols.
Aluminum trim
Use only neutral-pH produc ts to remove spots
and depos its from alum in um s urfaces.
C hr ome ca re products and alkaline cleaners
will attack alum in um s urfaces and can dam­
age them over time.
Cleaning and protec tion 209
A WARNING
A lways read and heed all WARNINGS and
other information
¢page 203.
Fabrics and fabric coverings
Fabr ics and fabric cover ings (e.g. seats, door
trim pa ne ls, etc.) shou ld be cleaned at regular
i n tervals w it h a vac uum cleaner. This removes
s ur face di rt particles which cou ld become em­
bedded in the fabri c throug h use. Ste am
cleaners sho uld not be used, beca use the
steam tends to p ush the dirt deeper into the
fabric and lock it there .
Normal cleaning
Generally, we recommend using a soft sponge
o r a lint -free microfibe r clo th to the clean fab­
ric. Br ushes shou ld only be used for carpets
and floor mats, since other fabric surfaces
could be harmed by br ushes.
Norma l su rface s tains c an be cleaned using a
commerc ially availab le foam cleaner . Spread
the foam on the s urface of t he fabric with a
soft sponge and work it in gently. Do not satu­
rate the fabric. T hen pat the foam dry us ing
absorbe nt, dry cloths (e.g. m icrofiber cloth)
and vacuum it after it has dried completely.
Cleaning stains
Stains caused by beverages (e .g. coffee, fr uit
juice, etc.) can be treated with a mild deter­
gent solution. Apply the detergent sol ution
with a spo nge. In the case of stubborn stains,
a detergent paste can be applied directly to
the stain and worked into the fabric. After­
wards, use copious amounts of clean water to
remove the rem aining de terge nt. Apply the
w at er wit h a d am p clot h or sponge a nd pat
the fabric dry with an abso rbent, dry clot h.
Stains from choco late or makeup should have
de terge nt pa ste (e.g. o x-gall soa p) rubbed i n­
to them. Afterwa rds, remove the soap wi th
wa ter (damp sponge) .
Alcohol can be used to treat stains from grease, o il , lipstic k or a ballpoin t pen. M elted ..,_ •
•

@ Tips
- The discharged battery must be properly
connected to the vehicle's electrical sys­
tem. When jump start ing or charging the
battery, never connect the negative
ground cable to the battery negative post because the battery manager sys­
tem must be able to detect the battery's
state of cha rge. A lways connect the neg­
ative g round cab le to the negative
gro und post o f the battery manage r con­
trol uni t.
Use of jumper cables
Make sure to connect the jumper coble
clomps in exactly the order described below!
Fig. 2 08 Engine compartment: connecto rs for jump
start cables and charger
Fi g. 209 Jump start ing w ith the battery of another ve ­
hicle: @-booste r batte ry, @ -discharged vehicle bat ­
te ry
The procedure described below fo r connecting
jumper cab les is intended to provide a jump
start for your veh icle.
Vehicle with discharged batt ery:
.. Turn off lights and acc esso ries, move leve r
of automat ic t ransm ission to N (Neutral) o r
P (Park) and set pa rking brake .
Emergenc y situ ation s 2 71
Connect POSI TIVE(+) to POSITIVE (+ )
(red )
.. Open the red cover on the positive terminal
¢fig. 208.
1. Connect one end of the red positive cable
on the
jump sta rt bolt ¢ fig. 209 (D (bolt
under the red cover = "positive") of the ve­
hicle to be started @.
2. Co nnect th e other end to the pos itive ter-
mina l@ of the booster battery @.
Connect NEGATIVE( -) to NEGATIVE(-)
(black )
3. Connect one end of the black negative ca­ ble to the negat ive termina l@ of the
booster b attery @.
4 . Connect the othe r end to the
jump start
pin @ (bolts with hex head bolt = "nega­
tive") of the vehicle to be started @.
Starting the engine .. Sta rt the engine of the veh icle w ith the
booste r ba ttery @. Ru n the engine at a
moderate speed .
.. Start engine wit h discha rged vehicle battery
@ in the usual manner .
.. If the eng ine fails to start, do not keep the
starter cranking for longer than 10 seconds.
Wait for about 30 seco nds a nd the n try
aga in .
.. With engi ne runni ng, remove j umper cab les
from both vehicles in the exact
reverse o r­
de r .
.. Close the red cover on the positive term inal.
T he battery is vented to th e outside to p revent
gases from en ter ing the veh icle in ter io r. Ma ke
s ur e th at the j umper clamps are well connec t­
ed with their meta l parts in full con ta ct w ith
the battery term inals.
A WARNING
To avoid se rious personal injury and dam­
age to the veh icle, heed all warnings and
instructions of the jumper cable man ufac­
turer. If in doubt, call for road service .
- J umper cables m ust be long enough so
that the veh icles d o not touch.
-