2012 AUDI A8 lock

-Never w ash your ca r in bri ght sunlight.
Drops of water act as magnifying lenses
and may damage your paint.
- When yo u wash your car in the winter : if
you rinse your vehicle with a hose , be
careful not to aim the stream of water
direct ly at locks, or at door or hatch
openings -they can freeze shut.
- Never use sponges des igned to remove
i nsects, or any kitchen scouring sponges
or similar products . They can damage
you r paint finish .
- Never use a dry cloth or sponge to clean
the headlights . Only use wet cloths or
sponges to prevent scratches . It is best
to use soapy water.
- You should remove debris (such as in­
sects) from the headligh t lenses on a
regular basis , fo r example when refuel­
i ng yo ur vehicle. Never clean the he ad­
l ights w ith a dry clo th or sponge. Use a
wet cloth or sponge . It is best to use
soapy water.
@ For the sake of the environment
I n the interes t of the envi ronment, the ve­
hicle sho uld only be washed in specia l
wash bays.
Washing your vehicle with a power
washer
Cleaning the exter ior of your car with a high­
pressure power washer is safe as long as you observe a few simple rules.
~ Befo re using the power washe r, make sure
you have read and understood the WARN­
INGS
c> A in General information on
page 203 .
~ Always follow the operating instructions for
the power washer .
~ Make sure that the jet o n the spray hose
produces a "fan shaped spray ".
~ Do not hold the spray no zzle too close to
soft materia ls.
W hen clea ning the vehi cle w it h a powe r wash­
e r
always fo llow the operating instruc tions.
Cleaning and protec tion 205
This applies particu la rly to the operating
pre ssure and the spraying di stance. Keep a
distance from soft materia ls such as rubber
hoses or insulating material as we ll as sensors
and camera lenses.
Do not use a jet which sprays water in a direct
stream or one that has a rotating jet.
Water tempera ture sho uld no t exceed 140 ° F
(60 °().
A WARNING
N eve r wash t ires with a jet that sprays wa­
ter in a direct stream . T hi s could cause in ­
v isib le damage to the t ires and weaken
them, even i f the spray is from a re lative ly
long distance and for a sho rt time. Dam­
aged and weakened tires can fail and cause
accidents and personal i njury .
(D Note
To avoid damaging your vehicle, a lways
make sure that the re is suffic ient d istance
between the spray head and soft materials
li ke rubber hoses, plast ic pa rts and sound­
deaden ing ma ter ia ls as well as sensors
and camera lenses. Never a im th e sp ray
head at the same point for a long time .
This also applies to cleaning headlights
and painted bum pers. Remembe r: the
cl oser the nozzle is to the surface of the
mater ia l, the greater the stress on the ma­
terial.
Sensoren und Kameralinsen
- Entfernen S ie Schnee m it einem Handfeger
und Eis bevo rzugt mit einem losungsm ittel­
fre ien Enteisu ngsspray .
- Reinigen Sie die Sensoren (adaptive cruise
cont ro l*, Einparkhi lfe*) mit losungsm itte l­
fre iem Re inigungsmi tte l und einem weiche n
t ro ck enen Tuch .
- Befeuchten Sie die Kameralinse m it handel­
si.iblichem Glasrein ig ungsm ittel a uf Al ko­
holbasis und reinigen Sie die Linse mi t ei­
nem trockenen Tuch . Beim lane assist* wird
de r Bereich vor der Linse im Normalfall .,..
•
•

substance use d for u ndercoating cou ld
overheat an d cause a fire.
- Always read and heed all WARNINGS and
other information
¢ page 203.
Exhaust tail pipes
Road sa lt and other corros ive materials will
damage the mater ial in the exhaust tail p ipes
if they are not cleaned regu larly . Do not clean
the ta il p ipes with wheel cleaner, paint polish,
chrome polish or othe r abrasive cleaners .
C lean the tail p ipes with ca r ca re products
that are s uita ble for stain less stee l.
Your authorized Audi dealer can provide clean­ i ng p rod ucts that have been tested and ap­
p roved fo r your vehicle.
Care of interior
Infotainment components
The MMI/RSE* disp lay may be cleaned with a
soft cloth and commercially-ava ilable "LCD
cleaner" . The cloth should be coated light ly
when the clean ing solution when cleani ng the
d isplay.
The MMI/RSE* contro ls must be cleaned first
with a brush so that dirt does not enter the
un it o r enter between the buttons and the
h ousing. Then w iping the controls with a clot h
dampened wi th d ish dete rgent and water is
recommended.
(D Note
To preve nt sc ratches, only clean the dis­
p lay when it is d ry.
- To p reven t damage, ma ke s ure fluids do
not enter the cont rols.
Aluminum trim
Use only neutral-pH produc ts to remove spots
and depos its from alum in um s urfaces.
C hr ome ca re products and alkaline cleaners
will attack alum in um s urfaces and can dam­
age them over time.
Cleaning and protec tion 209
A WARNING
A lways read and heed all WARNINGS and
other information
¢page 203.
Fabrics and fabric coverings
Fabr ics and fabric cover ings (e.g. seats, door
trim pa ne ls, etc.) shou ld be cleaned at regular
i n tervals w it h a vac uum cleaner. This removes
s ur face di rt particles which cou ld become em­
bedded in the fabri c throug h use. Ste am
cleaners sho uld not be used, beca use the
steam tends to p ush the dirt deeper into the
fabric and lock it there .
Normal cleaning
Generally, we recommend using a soft sponge
o r a lint -free microfibe r clo th to the clean fab­
ric. Br ushes shou ld only be used for carpets
and floor mats, since other fabric surfaces
could be harmed by br ushes.
Norma l su rface s tains c an be cleaned using a
commerc ially availab le foam cleaner . Spread
the foam on the s urface of t he fabric with a
soft sponge and work it in gently. Do not satu­
rate the fabric. T hen pat the foam dry us ing
absorbe nt, dry cloths (e.g. m icrofiber cloth)
and vacuum it after it has dried completely.
Cleaning stains
Stains caused by beverages (e .g. coffee, fr uit
juice, etc.) can be treated with a mild deter­
gent solution. Apply the detergent sol ution
with a spo nge. In the case of stubborn stains,
a detergent paste can be applied directly to
the stain and worked into the fabric. After­
wards, use copious amounts of clean water to
remove the rem aining de terge nt. Apply the
w at er wit h a d am p clot h or sponge a nd pat
the fabric dry with an abso rbent, dry clot h.
Stains from choco late or makeup should have
de terge nt pa ste (e.g. o x-gall soa p) rubbed i n­
to them. Afterwa rds, remove the soap wi th
wa ter (damp sponge) .
Alcohol can be used to treat stains from grease, o il , lipstic k or a ballpoin t pen. M elted ..,_ •
•

Care and handling
Because of the exclusive nature of the types of
leather that Audi uses and their unique prop ­
erties (such as sensitivity to oils, grease, soi l­
ing, etc.), you will need to be somewhat care­
fu l with these leathers, and a certain type of
care is required. For examp le, dark cloth ing
materials can d iscolor leather seats (especial­
ly if such cloth ing is damp and was not dyed
correctly) . Dust and d irt part icles in pores,
fo lds, and seams can have a n ab ras ive effect
and can damage the leathe r sur face as well as
weaken seams.
The leather should be cleaned regularly as
n eeded . After having been used for a re lative ly
long t ime, yo ur leather seats will acqui re a
rich aged finish. This is a characteristic of nat­
ura l leather and a sign o f true quality .
I n o rder to maintain the va lue of th is natura l
p rod uct over the life of yo ur vehicle, you
should follow the recommendations below :
(D Note
-To keep you r leather from bleach ing out,
do not a llow i t to be exposed to bright
s unli ght for long periods of time. If you
have to leave the vehicle parked o utside
for long periods, cover the leather to protect it from d irect exposure to sun­
li ght.
- Sharp objects on clothing, such as zip­
pers, rivets or sharp pieces on be lts can
l eave permanent scratches or scrape
marks on the surface of the leather.
(D} Tips
- After each time you clean the leather and
at regular interva ls, use a leather preser­
vat ive creme that conta ins UV-blockers
and that works into the leather . This
creme w ill nou rish and moistur ize the
l eather, helping it to b reath e and stay
supple. It al so helps to b uild up a pro tec­
tive coat ing o n the s urface.
- Clean the leathe r every 2 -3 months,
and clean a ny a reas that get soiled .
Cleaning and protec tion 21 1
- Remove fresh ma rks made by ballpo int
pens, ink, lipstick, shoe po lish, etc. as
soon as poss ible .
- Preserve the color of the leather as need­
ed by using a specia l co lored leather care
creme to touch up areas of uneven color.
Cleaning and caring for leather
upholstery and trim
App lies to vehicles: with natural leather
Natural leather requires special care and a t­
tention .
Normal clean ing
.. Clean soiled areas with a slightly moistened
cotton or woolen cloth .
More stubborn dirt
.,. More s tubborn di rt ca n be removed using a
cloth sa turated wi th a mild soap sol ution (2
tablespoons mild liq ui d soap) .
.. Never a llow the soap so lution to saturate
the leather, and make certain that no water
s oak s in to the seam s.
.,. Wipe off the soap so lu tion with a soft, d ry
cloth .
Cleaning spots
.. Remove fresh wate r-based spots (such as
coffee, tea, juices, blood) with an absorbent
cloth or paper towel.
.,. Remove fresh
grease or oil -based spots
(such as butter , mayonnaise, chocolate) with
an absorbent clot h or paper towel, or use
the cleaner from the leather care kit if the
spot has no t yet penetrated into t he surface
of the leather .
.,. Use an oil/grease dissolving spray, i f
oil/
grease spot s have d ried on.
.. Remove specific kinds of spots (ballpoint
pen, fe lt marker, fingerna il polish, water ­
based pa int, shoe po lish, etc.) with a spot
remover specifically formu lated for lea ther.
Leather care
.. Every half yea r use an approved leather care
product (available from your Audi dea ler) to
care for the leather . .,.
•
•

-Wh en cl eaning your safety belts, inspect
them for damage. If you discover dam ­
age, see your Audi dealer .
- Always read and heed all WARNINGS and
other information ¢
page 203.
Cooler
Applies to veh icles: with coole r
A layer of ic e or frost in th e cool er interfer es
with its cooling performanc e.
Cleaning
The refr igerator sho uld be cleaned reg ula rly .
.,. Wash the cooler w ith lukewarm water a nd a
mild cleaning so lution, if necessary .
.,. The n w ipe the coole r dry.
.. Dust and dir t will acc umu late near the ven ­
t il ation openings in the luggage compar t­
me nt due to normal coole r usage. This
sho uld be cleaned reg ularly.
Defrosting
.,. Switc h the coo ler off ¢ page 72.
.. Remove any food or beverages and al low
the coole r to defrost with the door open .
.. Wipe the inside of the coo ler dry and clean
the cooler , if necessary .
D efrost the cooler if yo u will no t be using it
for ex tended periods of time .
Q) Note
-Do no t try to speed up the defrosting
p rocess by applying heat.
- To red uce the risk of pe rsonal injury or
dam age to the refrige rator,
- do not use any abrasive cleaners, sol­
vents, wax, aggressive cleaning solu­
tions , so lutions with strong fragrances,
etc.,
- do not clean the coo ler with cleaning
tools such as stee l wool.
l ) U se o nly the co rr ec t cl ean in g so lu tio ns. Ne ve r use ga s­
o line or d ie sel fuel.
Cleaning and protec tion 213
Engine compartment
Be especially careful when cleaning the en­
gine compartment.
Always switch off the ignit ion before clean ­
ing the engine
¢ .& .
Plenum panel
Remove leaves from the plenum panel in front
of the windshield under the engin e compart­
ment . This prevents the water drain holes
from becoming b locked , and it preve nts de­
bris from entering the vehicle interio r through
the heat ing and ventilat ion ducts .
Corrosion protection
The eng in e compartm ent and transmission
have been corrosion-protected at the facto ry .
Good anti -corrosion treatment is very impor ­
tant , partic ularly in the w inte r.
If the vehicle
is frequently d riven on salt treated roads, th e
entire engine compartment and p lenum panel
shou ld be thoroughly cleaned at the end of
winter a nd retreated to p revent salt damage .
At the same time, the unde rside of the vehicle
shou ld be washed as well.
If the engine compar tment is cleaned at any
time with grease remov ing solutions
1> , or if
you have the engine washed, the ant i-corro­
s io n treatment is almost always removed as
well.
It i s therefo re essentia l to have a long­
lasti ng cor rosion pro tect ion rea pplied to all
s u rfaces , seams, joints and components in the
engine compartment .
A WARNING
Be aware: The engine com partment of any
motor veh icle is a potentially hazardous
area.
- Before work ing in the engine compart­
ment, be sure to read the information
¢ page 219 .
•
•

216 Fuel supply and filling your fuel tank
-Blend must contain not more than 15%
MTBE.
Seasonally adjusted gasoline
Many gasoline grades are blended to perform
espec ially we ll for winter or summer driv ing.
During seasonal change-over, we suggest that
you fill up at busy gas stat ions where the sea­
sonal adjustment is more likely to be made in
time.
(CT) Note
- Methanol fuels which do not meet these
requirements may cause corrosion and
damage to plastic and rubber compo­
nents in the fuel system .
- Do not use fuels that fai l to meet the
specified criteria in this chapter.
- If yo u are unable to determine whether
or not a particular fuel blend meets the
specifications, ask your service station or
its fuel sup plier.
- Do not use fuel for which the contents cannot be identified.
- Fuel system damage and performance
problems resulting from the use of fuels
different from those specified are not
the respons ibility of Audi and are not
covered under the New Vehicle or the Emission Control System Warranties.
- If you experience a loss of fuel economy
or driveability and performance prob­ l ems due to the use of one of these fuel
blends, we recommend that you switch
to unblended fuel.
Gasoline additives
A major concern among many auto manufac ­
turers is carbon deposit build- up caused by
the type of gasoline you use.
A lthough gasoline grades differ from one
manufacturer to another, they have certain
things in common. All gasoline g rades contain
substances that can cause deposits to co llect
on vital engine parts, such as fuel injectors
and intake valves. Although most gasoline
brands include additives to keep engine and fuel
systems clean, they a re not equally effec­
tive .
A udi recommends using TOP TIER Detergent
Gasoline. For more information on TOP TIER
Detergent Gasoline, please go to the official
website (www.toptiergas.com).
After an extended period of using inadequate
f uels, carbon deposit build-ups can rob yo ur
engine of peak performance.
(D Note
'
Damage or malf u nct ion due to poor fuel
quality is not covered by the Aud i New Ve­
hicle Limited Warranty.
Fuel tank
Fuel filler neck
The fuel filler neck is located on the right rear
s ide panel behind the fuel filler flap.
If the power locking system should fail, you
can still open the flap manually- for detailed
instructions see
¢page 218.
You can find the fuel tank capacity of your ve­
hicle in
Technical Data ¢ page 278.
The label on the inside of the fuel fi ller flap
tells you the correct fue l for your veh icle. For
more information about fuel specifications,
see
¢ page 215.
Your vehicle fuel tank has an on board refuel­ li ng vapor recovery system. This feature helps
to prevent fuel vapors from escaping from the
tank and polluting the environment while you refuel your vehicle . In order to fill the tank
properly wh ile protecting the environment,
please fo llow this refueling procedure careful­
ly.
.8, WARNING
Under normal operating cond itions, never
carry additional fuel containers in your car.
Gas canisters and other containers used to
transport fuel can be dangerous. Such con­
tainers, full or empty, may leak and could
cause a fire in a collision. If you must

transport fuel to use for your lawn mower,
snow blower, etc., be very careful and al­
ways observe local and state laws regard­
ing the use, transportation and storage of
such fuel containers. Make certain the con­
tainer meets industry standards (ANSI/
ASTM F8S2 -86) .
@ Note
Never drive your vehicle until the fuel tank
is completely empty. The irregular supply
of fuel can cause misfiring. Gasoline could
enter the exhaust system and damage the
catalyt ic converter.
Refuelling
Fig. 169 Right rear vehicle s ide: Opening the fuel filler
flap
Fig. 170 Fuel filler flap with attached fuel cap
When activating the central locking, the fuel
f ill er flap is automatically un locked or locked.
Refuel the vehicle with the ignition switched
off.
Taking the fuel cap off
• Press the left side of the fuel filler flap to
open it¢
fig. 169 -arrow-.
• Unscrew fuel filler cap counter-clockwise
and hang it on the fuel filler flap
~ fig. 170 .
Fuel supply and filling your fuel tank 217
Refuelling procedure
• Insert the fuel nozzle from the gasoline
pump into the fuel filler neck as far as it will
go.
• Select a medium refuelling rate so that the
nozzle switches off automatically when the
tank is full.
Putting the fuel cap back on
• After filling your tank, twist the fuel filler
cap clockwise as far as it will go.
• Close the fuel filler flap.
To avoid fuel spill ing or evaporating from the
fuel tank always close fuel filler cap proper ly
and completely. An improperly closed fuel fill­
er cap may also cause the MIL lamp ¢
page 26
to come on.
A WARNING
Improper refueling or handling of fuel can
cause fire, explosion and severe burns.
- Fuel is highly flammable and can cause
severe burns and other injuries.
- Failure to shut the engine off while refu­
eling and/or to insert the pump nozzle
fully into the fuel filler neck could cause
fue l to spray out of filler neck or to over­
flow. Fuel spray and overflowing fuel can
cause a fire.
- Never use a cellular telephone while re­
fue ling. The electromagnet ic radiation
can cause sparks that can ignite fuel va­
pors and cause a fire.
- Never get back into your vehicle while re­
fueling.
If in exceptional circumstances
you must get back in your vehicle while
refueling, make certain that you close
the door and touch metal to discharge static electricity before touching the fill­
er nozzle again. Static electricity can
cause sparks that can ignite fuel vapors
released during refueling.
- Never smoke or have an open flame any­
where in or near your vehicle when refu­
eling or filling a portable fue l container.
- For your safety, we strongly recommend
that you do not travel with a portable

218 Fuel supply and filling your fuel tank
fuel container in your vehicle. The con­
tainer, full or empty may leak and could
cause a fire, especially in a crash.
- If, under exceptional circumstances, you
must transport a portable fuel container,
please observe the following:
- Never fill a portable fuel container
while it is anywhere in or on the vehicle
(for example, in the luggage compart­
ment, or on the trunk). Static electrici­
ty can bui ld up while filling and can ig­
nite fuel vapors causing a fire .
- Always place a portable fuel container
on the ground before filling.
- Always keep the filler nozzle complete­
ly inside the portable container before
and during filling.
- If filling a portable container made of
metal, the filler nozz le must always be
in contact with the container. This will
help prevent static electricity from dis­
charging and cause a fire .
- Never spill fuel inside the vehicle or
luggage compartment. Fuel vapors are
highly flammable.
- Always observe local and state/provin­
cial laws regarding the use, storage
and transportation of fuel conta iners .
- Make certain the fuel container meets
industry standards (ANSI/ ASTM
F8S2 -86) .
d) Note
If any fuel has spilled onto the car, it
should be removed immediate ly to prevent
damage to the paint.
@ For the sake of the environment
As soon as the correctly operated noz zle
switches off automatically for the first
time, the tank is full. Do not try to add
more fuel because fuel may spill out. In
addition, the expansion space in the fuel
tank will be filled -causing the fuel to
overflow when it becomes warm and pol­
lute the environment.
(D Tips
-Running your engine whi le refue lling
may cause vapors to escape or even
cause fuel to spi ll out of the tank. This
would then shut off the fuel nozzle be­
fore the tank is full.
- Do not refuel your vehicle with the igni­
tion switched on. The fuel gauge may otherwise not ind icate the correct fuel
level after refuelling .
- The fuel filler flap of your vehicle is not
locked when you lock the vehicle from
the ins ide .
Fuel filler flap emergency release
You can open the fuel filler flap by hand if the
power locking system should fail.
Fig. 171 Rig ht s ide t rim p an el in t he luggage compart·
men t: emerge ncy re le ase mechan is m
The emergency release mechanism is located
behind the right side trim panel in the lug ­
gage compartment .
.,. Loosen the loop
¢fig. 171 from the retain­
er and then pull on the loop carefully
¢ (D.
.,. Press on the left side of the fuel filler door
to open
¢ page 217, fig . 169 .
(D Note
Only pull on the loop until you feel resist­
ance . You w ill not hear it release . Other ­
wise you could damage the emergency re­
l ease mechanism.

220 Check ing and filling
- Never smoke or work near heaters or
open flames. Fluids in the engine com­
partment could start a fire.
- Keep an approved fire extinguisher im­
mediately available.
- To avoid electrical shock and persona l in­
jury while the engine is running or being
started, never touch:
- Ignition cables
- Other components of the high voltage
electronic ignition system.
- If you must perform a check or repa ir
with the engine running:
- First, fully apply the parking brake,
move selector lever to "P" (Park) .
- Always use extreme caution to prevent
clot hing, jewe lry, or long hair from get­
ting caught in the radiator fan, V-belts
or other moving parts, or from contact­ ing hot parts. Tie back hair before
start ing, and do not wear cloth ing that
will hang or d roop into the eng ine.
- Min imize exposure to emission and
chem ica l hazards c:> &. .
A WARNING
California Propos ition 65 Warning:
- Engine exhaust, some of its constituents,
and certa in veh icle compone nts co nta in
o r emit chemicals known to the State of
Californ ia to cause cancer and b irth de­
fects a nd rep roduct ive ha rm. In addition,
c ertain f luids con ta ine d in vehicles and
c ertain pro ducts of component wear co n­
tain or emi t chemicals known to the
State of California to cause cancer and
birth defects or other reproductive harm.
- Battery posts, terminals and re lated ac ­
cessories contain lead and lead com- pounds, chemica
ls known to the State of
California to cause cancer and reproduc­
tive harms. Wash hands after handling.
(D Note
When adding f luids, always make su re that
they are poured into the proper conta iner
or f iller opening, otherwise serious dam­
age to vehicle systems w ill occur.
® For the sake of the environment
To detect lea ks in time, inspect the vehicle
floor pan from underneath regularly. If
you see spots from oil or other veh icle flu­
i ds, have you r vehicle inspected by a n au­
thorized Audi dealer.
Closing the engine hood
.. Pull the hood down until the pressure from
the struts is reduced.
.. Let the hood
drop down an d latc h in place.
Do not try to push it shut; it may fail to en­
gage 9 /]}. .
A WARNING ,_ -
A hood that is not completely latched
could fly up and b lock your view while dr iv­
i ng.
- When you close the engine hood, check it to make sure the safety catch has proper­ly engaged. The hood shou ld be flush
wit h the surrou nding vehicle body pa rts .
- If you notice while driv ing that the hood
is not secured properly, stop at once and
close it.