2012 AUDI A8 ignition

windshield wipers react to moisture on the
windshield. You can deactivate rain sensor
mode in the MMI, which will then activate in­
termittent mode. Select:
ICARI function but­
ton
> Car systems control button > Driver as­
sist > Rain sensor> Off.
In intermitten t
mode, you can adjust the interval time using
the switch @.
@-Slow wiping
@-Fast wiping
©-Single wipe. If you hold the lever in this
position longer, the wipers switch from slow
wiping to fast wiping.
® -Clean the windshield . The wipers wipe
one time after several seconds of driving to
remove water droplets. You can switch this
function off by moving the lever to position ®
within 10 seconds after the afterwipe. The af­
terwipe function is reactivated the next time
you switch the ignition on.
Cleaning the headlights. The headlight wash­
er system* only functions when the lights are
sw itched on. The headlights and the night vi­
sion system camera* are cleaned automatical­ ly the first time the lever is press in position
® and every 8 times it is pressed after that.
They are also cleaned every time you hold the lever in position @for longer than 8 seconds .
A WARNING
- The rain sensor is only designed to assist
and support the driver.
It remains entire­
ly the driver's responsibility to monitor
outside weather conditions and to man­
ually activate the wipers as soon as rain
or drizzle reduces visibility through the
windshield.
- The windshield must not be treated with
water-repellent materials. They can in­
crease glare under poor visibility condi·
tions such as wetness, darkness, or when
the sun is low on the horizon. In addi­
tion, they can cause the windshield wip­
ers to chatter.
- Properly functioning windshield wiper
blades are required for a clear view and
Clear vision 49
safe driving ¢ page 50, Replacing
windshield wiper blades.
(D Note
- In the case of frost, check whether the
windshield wiper blades are frozen to the windshield. Switching on the wind­
shield wipers can damage the wiper
blades!
- Prior to using a car wash, the windshield
wiper system must be switched off (lever
in position @). This helps to prevent un­
intentional switching on and damage to
the windshield wiper system.
- Do not use the wipers to clear a frosted
window . Using the wipers as a conven­
ient ice scraper will destroy the wiper
blades.
@ Tips
- The windshield wipers are switched off
when the ignition is off . Activate the
windshield wipers after the ignition is
switched back on by moving the wind­
shield wiper lever to any position.
- Worn or dirty windshield wiper blades
result in streaking. This can affect the
rain sensor function. Check your wind­
shield wiper blades regularly.
- The washer fluid nozzles of the wind­
shield washer system are heated at low
temperatures when the ignition is on.
- When stopping temporarily, e.g. at a
traffic light, the set speed of the wind­
shield wipers is automatically reduced by
one speed.

50 Clear vis ion
Replacing windshield wiper blades
Wiper blades in good condition help keep the
windshield clear .
Fig. 45 Remov ing wi nds hield w ipe r blade s
Service p osition
"" Switch the w indshield wipe rs off (posit io n
@ ¢ page 48, fig . 44).
"" Se lect in the M MI:: !CAR !f unc tion button>
Car system s contro l button > Se rvicing &
checks > Wip er service position > On . The
windshield wipers move into the serv ice po­
s it ion.
O r
"" Switc h the ignition off and move the wind­
shield wiper lever to posit ion © ¢ page 48,
fig.
44.
Removing the wiper blade
"" Fold the windshield wiper arm away from
the windshie ld .
"" Press the locking knob
(D ¢ fig . 45 on the
wiper blade . Hold the wiper b lade firm ly.
"" Remove the w iper blade in the direction of
the arrow.
Installing th e wiper blade
"" Inse rt the new wiper b lade into the mount
on the wiper arm @until you hea r it latch
into place .
"" Place the wiper arm back on the windshie ld.
"" Switc h the ignition on .
"" Se lect : ICARI funct ion button >
Car sy stem s
control button > Servicing & checks > Wiper
servic e po sition
> Off .
Or
"" Press the w indshield wiper lever .
A WARNING
-If the windshie ld w ipers smear the wind­
sh ie ld, clean the wiper b lades w ith wind­
shie ld washer fluid .
If the wiper blades
are ext reme ly dirty, you can a lso clea n
them wi th a s oft sponge o r clo th.
- For your safety, you should replace the
wiper blades once o r twice a yea r. See
your author ized A udi de aler for re place­
men t blad es.
([) Note
-The windshield wip er b lades must only
be folded away when in the service pos i­
ti on! Ot herwise, you ris k damaging the
p aint on the hood o r th e windshie ld w ip­
er motor.
- Yo u should no t move your veh icle or
press the windsh ie ld wiper lever when
t he wipe r arms are folded away from the
w indshield. The windshie ld wipers wou ld
move back into their or iginal position
and co uld damage the hood and wind­
shield.
- To help prevent damage to the w iper sys­
tem, always loosen blades wh ich are fro­
zen to the windshield before operating
w ipers .
- To help prevent damage t o wiper blades,
do not use gasoline, kerosene, paint
thinne r, or o ther solven ts on o r near the
w iper blades .
- To help prevent damage to the w iper
arms or other components, do not at­
tempt to move the wipe rs by hand .
(j) Tips
- Comme rcial hot waxes appl ied by a uto­
matic ca r washes affect the cleanability
of t he windshie ld.
- Yo u can also use the se rv ice posi tion, for
example, if yo u want to p rotec t the
w indshield from icing by using a cover.
- Yo u cannot activate the se rv ice position
w hen the hood is ope n.

Mirrors
Adjusting the exterior mirrors
Fig . 46 Fo rwa rd section of d river's a rmrest: power m ir­
ror co nt rols
Turn the knob to the desi red position :
Q/P -In th is position, you can adjust the
driver's and front passenger's exter ior mir rors
by turn ing the knob in t he des ired direction .
® -The m irrors are heated depending on the
outside temperature .
8 -The exterior mirrors fo ld in. In the MMI,
you can select if the m irrors fold in automat i­
cally when you lock the vehicle
9 page 31.
Tilt function fo r th e pa sseng er' s mi rror
To help yo u see the curb when backing into a
parking space, the surface of the mirror tilts
slightly. The knob must be in the P position
for this to happen .
You can ad just the tilted mirror s urface by
turning the knob in the desired direction.
When you move out of reverse and into anoth ­
er gear, the new mirror posit ion is stored and
assigned to the key you are using.
The mirror goes back into its origina l posit io n
once you drive forward faster than 9 mph (15 km/h) or switch the ignition off .
A WARNING
-Curved ( i.e. convex) mirror s urfaces in­
crease your field of view . Remember that
vehicles or other objects will appear
small er and farther away than when seen
in a flat m irror.
If you use this mirro r to
est imate distances of following vehicles
Clear vi sion 51
when changing lanes, you co uld estimate
incorrectly and cause an accident.
(D Note
- If the m irror housing is moved uninten ­
tionally (for examp le, w hile pa rking your
vehicle), then yo u must first fold the mir­
ror electrically. Do not read just the mir­
ror housing man ually. You cou ld damage
the motor which controls the mirror.
- If you wash the vehicle in an automatic
car was h, you must fold the exter ior mir­
rors in to reduce the risk of damage to
the mirrors. Never fold power fold ing ex­
terior mirrors by hand. O nly fold t hem in
and out using the power controls.
(D Tips
- T he exterior m irror set tings are stored
w ith the m emory function*
9 page 62 .
- If there is a malfunction in the elect rical
system, you can st ill adjust the exterio r
mi rrors by pressing the edge of the m ir­
ror.
Dimming the mirrors
Fi g. 47 Auto m atic d immin g rearv iew mirr or
.. To dim the rearview m irror and both exteri ­
or m irrors, press the@ button . The diode
@ tu rns on. The rearview and exterior mir­
rors dim automatically whe n light shines on
t hem, for examp le from headl ights on ave-
hicle to the rear . ..,.

Front passenger's seat
Always move the front passenger seat into the rearmost position .
To avoid contact with the airbag while it is de­
ploying, do not sit any closer to the instru­
ment panel than necessary and always wear
the three-point safety belt provided adjusted correctly . We recommend that you adjust the
passenger's seat in the following manner:
.. Bring the backrest up to an (almost) upright
pos it ion .
Do not ride with the seat reclined .
.. Adjust the head restra int so the upper edge
i s as even as possib le wit h the top of you r
head .
If that is not possib le, try to adjust
the head restraint so that it is as close to
this position as possible ¢
page 61.
.. Place your feet on the floor in front of the
passenger's seat.
Front seats
Controls
Moving the seat forward or back and adjust­
ing the height , backrest angle and seat an­
gle.
F ig . 50 Fron t seat: adju sting th e seat
@ -Mov ing the seat forward/back: press the
button forward/back ¢ .&, .
@ -Mov ing the sea t up/down : p ress the but­
ton up/down ¢& . To ad just the front sect ion
of the seat, press the front button up/down
¢ .&, .To adjust the rear sect ion of the seat,
press the rea r button up/down
c> ,& .
@ -Turn the massage function on/off. You
can select the type of massage using the mu l­
tifunct ion button
c> pag e 56.
Sea ts a nd s to rage 55
© -Backrest forward/back: press the button
forward/back ¢ .&, .
©-Comfort head restraints¢ page 61,
¢,& .
(D -Multifunction button¢& , ¢ page 56 .
A WARNING
-Never adjust the driver's or front pas­
senger's seat whi le the vehicle is moving.
If you do th is while the veh icle is moving,
you will be out of position. A lways adj ust
the dr iver's or front passenger's seat
when the vehicle is not moving.
- Be ca reful when adj usting the seat
height. Check to see that no one is in the
way, or serious injury cou ld resu lt!
- Because the seats can be electrically ad­
justed with the ignition off, never leave children unattended in the vehicle . Unsu­
pervised use of the electric seat adjust­
ments may cause serious injury.
- To reduce the risk of injury in the case of
sudden braking or accident, front pas­
sengers must never ride in a moving ve­
hicle with the back rest reclined . Safety
be lts and the airbag system on ly offer
maximum protection w hen the backrest
is upr ight and the safety belts are prop­
erly positioned on the body . The more
the backrest is reclined, the greater the risk of persona l injury from an incorrect
seating position and improperly posi­
tioned safety belts.

56 Seats and storage
Multifunction button
App lies to vehicles: wit h memory fu nctio n
You can adjust the massage function, upper
section of the backrest, lumbar support, side
bolsters, seating surface and safety belt
height using the multifunction button.
F ig. 51 MMI display : seat settings
Operating
• The M MI displays the possible seat settings
@ when yo u turn the mu ltifunction button
page 55, fig. 50 to the left or right
c:> fig. 51, c:> .&_.
• To select a seat setting, turn the multifunc­
tion button
is h ighlighted with a red border.
• The arrows @ indicate the possible adjust­
ments . For example, to move the lumbar
support down, press the multifunct ion but­
ton
l ights up .
The following seat settings @are possible:
Mas sage funct ion * -Massage type Wave,
K nock in g, Stretch, Lumbar , Sho ulder or Off .
You can set the massage strength level from 1
to 5 . You can turn the selected massage on/
off us ing the button @
c:> page 55, fig. 50 .
Safety belt h eight adju stment * -Moving the
safety belt up/down
c:> page 139, c:> .&..
Upper backre st -Moving the ang le of the up­
per section of the backrest forward/back
c:> &.
Lu mb ar support -Moving the lumbar support
up/down and making it firme r/softer
c:> .&. .
Side bol ster s* -Increasing/reducing the side
support in the seat using the side bolsters on
the seating surface and backrest
c:> &.
Seat ing surfa ce -Making the seat ing s urface
longer/shorter
c:> A .
A WARNING
-
-Never ad just the driver's or front pas­
senger's seat whi le the vehicle is moving.
If you do this while the vehicle is moving,
you will be out of position. A lways adjust
the dr iver's or front passenge r's seat
when the vehicle is not mov ing.
- Be careful when adjusting the seat
he ight . Check to see that no one is in the
way, or serious injury cou ld result!
- Because the seats can be electrically ad­
justed with the ignition off, never leave
children unattended in the veh icle. Unsu­
perv ised use of the e lectr ic sea t adj ust­
men ts may cause serious injury.
- To reduce the risk of injury in the case of
sudden b raking or acc iden t, front pas­
sengers mus t
never ride in a movi ng ve­
hicle with the backrest reclined . Safety
be lts and the airbag system only offer
maximum protection when the backrest
is upright and the safety belts are prop­
erly positioned on the body . The more
the backrest is reclined, the greater the risk of personal injury from an incorrect
seating position and improperly pos i­
tioned safety belts .
@ Tips
-The massage function switches off auto­
matically after approximately 10 mi­
nutes.
- In vehicles w ith the reclining rear seat,
only the safety belt he ight and the seat­
ing surface can be adjusted on the front
passenge r sea t using the mul tifunc tion
butto n.

58 Seats and storage
© -Switching front passenger seat adjust ­
ment on/off: this function must be activated
in the MMI ¢
page 60, ¢& .To switch front
passenger seat adjustment on, press the but­
ton. You can now adjust the front passenger
seats us ing the buttons @ and @. If you do
not press the buttons @ or@ , front passen­
ger seat adjustment switches
off automatica l­
ly after approximate ly ten seconds.
& WARNING
- T he power adjustment for the individ ual
seats also works with the ignition . For
this reason, children should never be left
unattended in the vehicle -th ey could be
injured!
- Exercise caution when adjusting the
seats. Uns upervised or careless seat ad­
justment can p inch fingers or hands
causing injur ies.
- Vehicles with a pass through in the cen­
ter console have seat ing for four. The
long center console between the two
Reclining rear seat overv iew
Applies to vehicles: with reclining rear seat
----------------- T ® ------ -
Fi g. 54 Rear doo r: ad justi ng the recli ning posit ion
(D -Adj usting the reclining posi tion
@ -Adjusting the standard position rear seats is
n
ot a seat ing position.
Therefore, a safety belt is not provided.
(D Note
If a child seat is attached to one of the rea r
seats, this seat must not be adj usted using
the power controls under any circumstan­
ces. The easy entry funct ion for this seat
must also be deactivated in the MMI
¢
page 60 . The child seat as well as the
r ear seat can be damaged by the adjust­
ment process.
© Tips
The massage function switches off auto­
matically after approximately 10 minutes.
- If you cannot
move the front passenger
seat, it may be because
- the front passenge r's seat memory
f u nction is swi tched off ¢
page 63 or
- the child safety lock is switched on (the
@ b utton ¢ page 38 or t he righ t t
button ¢ page 38 lights up in the d riv ­
er's door), or
- the front passenger seat adjustment is
switched
off in the MMI ¢ page 60.
@ -Fold ing the leg support up/down
@ -Leg support steeper/flatter
i :c ., a,

64 Seats and storage
Full-length center
console
Overview
Appl ies to vehicles: with full-len gth ce nter console
Fig. 61 Rear: full -length center console
@ · 115 volt socket ¢ page 64
@ · cupholder <=> page 71
© · 12 volt socket c:> page 70
@ · Folding table ¢ page 65
®·center armrest and storage com part ·
ments: to open the deep compartment, press
the right button and fold the center armrest
upward. To open the compartment for the
massage function remote control*
c:> page 60
and for the telephone*, press the left button
and fold the center armrest upward.
115-volt socket
Applies to vehicles: with 115 -vo lt socket
The 115-volt socket can only be used when
the engine is running¢
A. When you push
the connector all the way into the socket, the
child safety mechanism releases and current
flows through the socket .
Equipment that can be connected
Electrical devices can be connected to the 115
volt socket in the vehicle. Power consumption
at the 115-volt socket must not exceed 150
watts (300 watts peak) . Check the power con·
sumption of the equipment on the model
plate .
LED on the socket
-The socket is ready for use when the LED is
green.
- If the LED blinks red, there is a malfunction.
The socket will switch off automatically due
to overcurrent or overheating. The socket
will switch on again automatically after a cool-down period. Any devices that are con­
nected and switched on will activate again
automatically
c:> A .
A WARNING
-
- The sockets and the electrical accessories
connected to them operate only when
the ignition is switched on. Incorrect us­
age can lead to serious injuries or burns.
To reduce the risk of injuries, never leave
children unattended in the vehicle with
the vehicle key.
- Heavy equipment or plugs with integrat­
ed power supply units can damage the
socket and lead to injuries.
- Store a ll connected equipment securely
while the vehicle is moving so that they
cannot be thrown through the vehicle in
the event of a braking maneuver or an
accident.
- Never spill any liquids on the socket. If
any moisture gets into the socket, make
certain that all the moisture has dried up before using the socket again.
- Equipment that is connected to the vehi·
cle socket can heat up more than it does
when connected to the public grid .
- When using adapters and extension
cords, the child safety for the 115-volt
socket is disabled and the socket is live.
- Never insert anything other than the
plug of an appropriate electrical accesso·
ry into the socket, especially things that
conduct electricity, e.g. metal pens, knit­
ting needles, etc. into the contacts of the
115-volt socket.
- Turn the electrical equipment off if the
socket has switched off because of over·
heating.

70 Seats and storage
-Never exceed the maximum permissible
load carrying capacity of the roof of your
vehicle, the permissible axle weights and
the permissible total weight of your vehi­ cle
c::, page 276, Weights .
@ For the sake of the environment
As a result of the increased wind resist­
ance created by a roof rack, your vehicle is
using fuel unnecessarily. So remove the
roof rack after using it.
12-volt sockets
Applies to vehicles: 12-volt soc kets
Electrical accessories can be connected to ev­
ery 12-volt socket.
Fig. 71 Sect io n of the trim panel of th e lu ggage com­
part ment: 12 -vol t soc ket
Fig. 72 Rear center conso le: 12-vo lt soc ket
... Open the socket cover c::, fig. 71 or c::, fig. 72 .
... Insert the plug of the electrical device into
the socket.
There is an additional 12 volt socket in the
front center console~
page 71, fig. 73.
The 12 volt sockets may be used for 12-volt
appliances with maximum consumption of up
to 100 watts . Before you purchase any accessories, always
read and follow
the information in
c::, page 282, Additional accessories and parts
replacemen t.
A WARNING
The sockets and the electrical accessories
connected to them operate only when the ignition is switched on . Incorrect usage
can lead to serious injuries or burns. To re­
duce the risk of injuries , never leave chil­
dren unattended in the vehicle with the ve­
hicle key.
(D Note
To avoid damaging the socket, only use plugs that fit properly.
- Never connect equipment that generates
electrical current, such as a solar panel
or battery charger, to the 12 volt socket .
This could damage the vehicle 's electri­
cal system.
- The 12 volt socket should only be used
for a short period of ti me as a power
source for electrical equipment. Please
use the electrical sockets in the vehicle
when connecting equipment for longer periods.
@ Tips
When the engine is off and accessories are
still plugged in and are on, the vehicle bat­
tery can still be drained.