Instruments and warning/indicator lights 19
!;.!~ Electronic stabilization program
(ESP)
This warning/indicator light monitors the
electronic stabilization program.
When you sw itch the ignition on, the indicator
light
G1 turns on briefly to check the function .
If thE:
G1 indicator lamp blinks while dr iving,
the ESP or ASR (Ant i- Slip Regulation) is active
ly regulating.
If thE:
hJ indicator lamp illuminates, the sys
tem has switched the ESP off.
If the indicator light
I turns on, the ESP was
switched to ESP sport mode with the button
I!]<=>
page 189. If this is case, you can reacti
vate the ESP by switching the ignition off and
then on again . The warning/indicator light
should go out to show that the system is fully
functiona l again.
Stability program and ABS fault! See own
er's manual
If the indicator light D] and the ABS indicator
light
m (USA mode ls) ;fl] (Canada models)
turn on and the message appears, there is a
malfunct ion in the ABS system or electron ic
differential lock . This also interrupts the ESP.
The brakes still function with their normal
power, but ABS is not active.
Drive to your authorized Aud i dealer immedi
ately to have the malfunction corrected .
If the battery term inals were disconnected
and re-connected, the vehicle was jump start
ed or the battery is very weak, the ESP sensor
system goes through a learning process for
the first few yards . The warning/ind icator
light illuminates . Th e warn ing/ indicator light
goes o ut as soon as the learning process is
comp lete.
For more informat ion about the ESP
<=> page 189. ABS/(
8) Anti-lock braking system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL) .
The warning/indicator light B (USA mod
els)
/ l(O] (Canada models) w ill come on for a
few seconds when the ignition is sw itched on .
The light will go out after an automatic check
sequence is comp leted.
There is a malfunction in the ABS when:
-The warning/indicator light does not illumi·
nate when you switch the ignition on.
- The warning/indicator light does not go out
after a few seconds.
- The warning/indicator light illuminates
while driving.
The ESP indicator light also illuminates if
there is a ma lfunction in the ABS . The mes
sage
Stability program and ABS fault! See
owner's manual
a lso appears in the instru
ment cluster d isp lay and a warning tone
sounds .
The brake system will still respond even
without the assistance of the ABS system.
See your authorized Audi dealer as soon as
possible to restore full braking performance.
Fo r more information regarding the ABS
<=>page 189.
Malfunction in the brake system
If the brake warning light<=> page 14 and the
ABS warning illum inate
together there may be
a malfunction in the ABS, and there may also
be a malfunction in the brake system itself
<=>
&. . The ABS will not work and you will no
tice a change in braking response and per·
formance .
In the event of a malfunction in the brake
system
the warning/indicator light _
(USA models)/ . (Canada models) in the in
strument cluster flashes <=>
page 14.
Malfunction in the electronic differential
lock (EDL)
T he EDL works t ogether w ith the ABS. The
ABS warning light will come on if there is a
26 Instruments and warning /indicator lights
Odometer
Fig . 10 In str ument cl uster: Odomete r an d reset but
ton
The odometer shows yo u how many mile s
(kilome ters) yo u have driven. You c an switch
the disp lay from mi les to kilome ters and vice
ve rsa via the M MI.
Upper odometer
Th e trip odom eter shows the d istance d riven
si nce i t was last rese t.
It can be used to meas
u re shor t distances. The l ast d igit in di cates
1/1 0 of a m ile ( 100 mete rs) .
You can reset th e trip o dom eter to ze ro by
p re ss ing the Reset button~-
Lower odometer
The lower odometer shows the total numbe r
of m iles (k ilometers) d rive n.
Malfunction message
If t here is a ma lfunction in the instrument
cluster ,
DEF will appear in the trip odometer
d isplay area. Contact your authorized Audi
deale r to have the p roblem corrected.
Time and date display
F ig. 11 I n str ume nt cluster : cloc k an d date
You can set the time and t he date disp lay in
the MMI. Refer to the M MI owne r's manual
f or instructions.
When yo u open the driver's door, the date and
time appea r in the inst rument cluster disp lay
for 30 seconds .
Service interval display
The service interval display reminds you when
your next service is due.
Fig . 12 Instrume nt c lu ste r: Se rvice inte rval disp lay
The schedule for the next o il change or inspec
tion is ca lculated automatically and disp layed
accord ingly . Th e d isp lay works in two stages:
Service reminder
30 days be fore the next service is d ue, a serv
ice reminder appears in the display when you
switch the ign ition on
¢ fig. 12.
After about 5 seconds the display switches
back to norma l. The distance and time re
mai ning are updated each t ime the ignit io n is
switched on until the date due for service is
r eached.
Service due
When the due date for se rvice is reached, the
message
Service due! appears in the instru
ment cluster immed iate ly after yo u sw itch the
ignition o n. Add it iona lly, a warning tone
sounds . After about 5 seconds the disp lay
switches bac k to normal.
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the MMI display by selecting
t h e service interval d isplay in the car menu.
II>
-When you leave the vehicle, always take
the ignition key with you. This will pre
vent passengers (children, for example)
from accidentally being locked in the ve hicle should they accidentally press the
power locking switch in the doors .
- Do not leave children inside the vehicle
unsupervised. In an emergency it would
be impossible to open the doors from
the outside without the key.
- Applies to vehicles with power side door
closer*:
- When closing a door, make sure noth
ing can interfere with the door. This
could cause serious personal injury.
- You can stop the door from closing at
any time by pulling on the inside or
outside door handle .
@ Tips
-In the event of a crash with airbag de
ployment all locked doors will be auto
matically unlocked to give access to the
vehicle occupants from the outside.
- If the power locking system should mal
function, you can lock the driver's door
using the mechanical key¢
page 36 .
-If the power locking system should fail,
you can still open the fuel tank flap in an
emergency ¢
page 218.
-You are well advised not to keep valua
bles inside an unattended vehicle, visible
or not . Even a properly locked vehicle
cannot provide the security of a safe .
- If the LED in the upper edge of the driv
er's door panel comes on for about 30
seconds after the vehicle is locked, there
is a malfunction in the power locking or
the anti-theft warning system. Have the
malfunction corrected by an authorized
Audi dealership or qualified repair facili
ty.
Opening and closing 33
Setting power locking
T he driver can determine the functions for
power locking in the MMI .
.,. Select: !CAR !function button> Car systems
control bu tton > Vehicle settings > Central
lo cking .
Unlock doors -
You can decide if All doors or
only the
Dri ver should unlock. The rear lid al
so unlocks when
All is selected . If you select
Driver in a vehicle with a convenience key* ,
only the door whose handle you pull will un
lock.
If you select
Driver , all the doors and rear lid
will unlock if you press the
ffi button on the re
mote control master key twice .
Lock exterior trunk handle -If you selec t On,
the rear lid handle is locked . In this case the
rear lid can be opened with the button
a on
the master key or with the
a button in the
driver's door . In vehicles with a convenience
key* , you can still open the rear lid using the
handle if an authorized master key is near the
proximity sensor .
Fold mirrors* -If you select On, the exterior
rearview mirrors fold in automatically when
you press the
(TI button on the remote contro l
master key or touch the sensor* in the handle .
Lock when driving -If you select On, the vehi
cle locks automatically when driving. All of
the doors and rear lid lock.
Tone when locking -When you select On, a
confirmation tone sounds when you lock the
vehicle.
42 Clear vision
visibility conditions. For example, fog cannot be detected by the light sensors.
So always switch on the headlights
io
under these weather conditions and
when driving in the dark.
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists . Always turn on
the headlights so that you can see ahead and so that others can see your car from
the back.
(D Note
The rear fog lights should only be turned
on in accordance with traffic regulation, as
the lights are bright for following traffic.
@ Tips
-In the event of a light sensor malfunc
tion, the driver is notified in the instru
ment cluster display~
page 22.
- You will hear a warning tone if you open
the driver door when the exterior lights
are switched on.
- Please observe legal regulations when
using the lighting systems described .
Emergency flasher
The emergency flasher makes other motorists
aware that you or your vehicle are in an emer
gency situation.
Fig. 33 Center console : emerge ncy flasher switch
• Press the switch~~ fig. 33 to turn the
emergency flashers on or off.
When the emergency flasher is on, all four
turn signals blink at the same time. The turn signal
indicato r lights ¢ Q in the instrument
cluster, as well as the light in the emergency
fl asher switch ~ blink likewise. The emergen
cy flashers also work when the ignition is
turned off.
The emergency flashers will turn on automati
cally if you are in an accident where the airbag
has deployed .
(D Tips
You should turn on the emergency flashers
when:
- you are the last vehicle standing in a traf
fic jam so that any other vehicles coming
can see you, or when
- your vehicle has broken down or you are
in an emergency situation, or when
- your vehicle is being towed by a tow
truck or if you are towing another vehicle
behind you.
· Adjusting the exterior lighting
The settings ore adjusted in the MMI.
• Select: I CAR I function button > Car systems
control button > Vehicle settings> Exterior
lighting.
Automatic headlights
You can adjust the following settings in the
Automatic headlights menu :
Headlights activation time -You can adjust if
the headlights switch on
Early , Med. or Late
according to the sensitivity of the light sensor .
Audi adaptive light* -You can switch adaptive
light
On and Off .
Daytime running lights
USA models:
You can switch the daytime run
ning lights
on and off.
Canada models:
The function cannot be
turned off.
It is activated automatically each
time the ignition is switched on. This menu
item is shown "greyed out".
By pressing the I START ENGINE STOPI button
without depressing the brake peda l, the igni
tion is on and switched
off by pressing it
again.
After a cold engine is started, the re may be a
brief period of increased noise because oil
pressure must first bui ld up in the hydraulic
va lve adjusters. This is normal and not a cause
for concern.
If the engine should not start immediately,
the starting process is automatically stopped
after a short time. Repeat starting procedure.
Driv er m essag e in th e in strument clu ste r
disp lay
Pr ess br ak e p ed al to start engin e
This message appears if you press the
I START ENGINE STOP ! button to start the en
g ine and do not depress the brake peda l. The
engine can on ly be started if the brake pedal
is depressed.
!!I C o nv enience ke y: I s ke y not in th e vehi
cle ?
This message appea rs a long with the !!I sym
bol if the maste r key is removed from the ve
hicle with the engine r unning . It is intended
to remind you (e .g . when changing drivers)
not to continue the journey witho ut the mas
ter key.
I f the master key is no longer in the vehicle,
you cannot sw itch on the ignition after stop
ping the engine and yo u also cannot start the
engine again. Moreover, you cannot lock the
veh icle from the outside with the key.
Shift to P , other wis e vehicle c an roll away.
Doo rs do not lock if le ver i s not in P.
This message appears for sa fety reasons
a long with an audib le warning tone if the
P
selector lever position is not engaged when
stopping the eng ine with the
I STAR T ENGINE STOP ! button. Select the P se
lector lever posit ion. Otherwise the veh icle
could roll and it can not be locked .
On th e ro ad 71
Ke y not r ecogni sed . Hold bac k of ke y again st
ma rked area. See owne r's manual.
If the indica tor l ight turns on and this mes
sage appears, there is a malf unct ion
¢ page 72.
Steering lock
The steering locks when you turn the engine
off using the I START ENGINE STOP ! button
and open the d river's doo r. T he locked steer
i ng helps p revent vehicle theft.
& WARNING ~
- Never allow the engine to run in confined
spaces -danger of asphyxiation .
- Never turn
off the engine un til the vehi
cle has come to a complete stop .
- The brake booster and power steering
only work when the eng ine is r unning . If
the engine is
off, you have to use more
force when steering or braking. Because
you cannot steer and brake as you usual ly would, this cou ld lead to crashes and
serious injuries.
(CT) Note
- Avo id h igh engine rpm, full thrott le and
heavy engine loads until the engine has
reached operating temperature -other
w ise you risk engine damage .
- The engine cannot be started by pushing
or towing the vehicle.
- If the engine has been under heavy load
for an extended per iod, heat builds up in
the engine compa rtment afte r the e n
gine is switched
off -there is a risk of
damaging the engine. Allow the engine
to run at idle fo r about 2 minutes before
switching it
off.
(D Tips
- If you open the d river 's doo r with the ig
nition on, a buz ze r sounds and the mes
sage
Ignition i s on appears in the instr u
ment cl uste r display . Sw itch the ignition
off . Ill-
Emergency braking
In the event that the conventional brake system fails or locks .
11-In an emergency, pull the switch(®) and
conti nue to pull it to slow your vehicle down
with the parking brake .
11-As soon as you release the sw itch (®) or ac-
celerate, the braki ng p rocess stops.
If you pull the sw itch
(®) and hold it above a
speed of about 5 mph (8 km/h), the emergen
cy braking function is in itiated. The vehicle is
b ra ked at a ll four wheels by activating the hy
d raul ic br ake system. The b ra ke performance
i s sim ilar to making an emergency stop~.&. .
I n o rder not to activate the emergency brak
i ng by m ista ke, an audible warning tone (bu z
z er) sounds when the switch<®> is p ulled. As
soon as the switch(®) is released, or the accel
erator pedal is dep ressed, emergency braking
stops .
.&_ WARNING
Emergency braking shou ld only be used in
an eme rgency, when the normal foot brake
has failed or the brake pedal is obstructed.
Using t he parking brake to perform emer
gency braking will slow you r vehicle down
as if you had made a fu ll brake applicat ion.
The laws of phy sic s ca nnot be s uspended
eve n w ith ESP and its associated compo
nents (ABS, ASR, ED L) . In co rners and
when road or weather conditions are bad,
a full brake application can cause the vehi
cle to skid or the rear end to b reak away -
r isking an accident.
Speed warning system
Introduction
The speed warning system helps you to stay
under a specified maximum speed.
The speed warning system warns you if you
are exceed ing the max imum speed that you
h ave set . You will hea r a warn ing tone when
your speed exceeds the stored va lue by ap-
On th e ro ad 75
proximately 3 mph ( 3 km/h) . An indicator
light . (USA
models) ;a (Canada mode ls) in
the instr ument cluster d isp lay also turns on at
the same time. The indicator light./.
turns off when the speed decreases be low the
stored maximum speed .
Setting a t hreshold is recommended if you
would like to be rem inded w hen you reach a
certain maxim um speed . S ituations where you
may wa nt to do so include driv ing in a country
with a general speed limit o r if the re is a
specified maximum speed for w inte r tires .
(D Tips
Even though your vehicle is eq uipped w ith
a speed warn ing system, you sho uld still
watch the speedometer to ma ke sure you
a re not dr iv ing faster t han the speed limi t.
Setting the threshold
You can set, change and delete the threshold
in the MMI.
11-Select: I CAR! function button > Car systems
control butto n > Driver assist > Speed warn
ing .
You can set any threshold between 20 mph
(30 km/h) and 150 mph (240 km/h). Sett ings
can eac h be ad justed in increments of 5 mph
(10 km/h).
-they are not in an upright position, for
examp le if they are s itting, crouching
or lying down and/or
- if the outline in the display is incom
p lete or interrupted, for example be
cause the person is partially hidden by
a parked veh icle .
(D Tips
-Pedestrian detection and the pedestrian
warming are lim ited to objects that are
detected as pedestr ians. The system
does not detect animals . Even though
the shape and warmth radiated by each
object det ected is evaluated, the system
does have lim itations and it can give in
correct warnings.
- Fo r techn ical reasons , the image pauses
in split second interva ls.
Switching on and off
Appl ies to vehicles: with night vision assistant
Fig . 103 Area a round the light switch: n ight v ision as
sistant button
.. Switch the ignition on and turn the light
switch to the
AUTO position or io.
.. To switch night vision assistant on, press
the
EJ button Q fig. 103. The image from
the night vision camera appears in the in
strument cluster d isplay.
.. Press the button
EJ again to switch night vi
s ion assistant off .
Night vision assistant 99
Settings in the MMI
Applies to vehicles: with night vision assistant
Fig. 104 Display : exa mple of pedest rian detectio n and
warn ing to n e switched off
.. Select: I CAR I function button > Car systems
cont rol button > Driver assist > Night vision
assist.
Highlight pedestrians -
You can switch pedes
trian detect io n
on and off . If you switch pe
destrian detection off, the pedestrian warning
tone also switches off . The symbols
I) and r2J
appear in the upper right area of the instru
ment cluster disp lay ¢
fig. 104.
Warning tone -You can switch the tone for
the pedestrian warning
on and off. When the
warning tone is sw itched off, a yellow symbol
for the deactivated warning tone with a line
through it appears in the upper right of the in
strument cluster display¢
fig. 104.
Contrast -When the night vision assistant is
switched on and the image is visib le in the in
strument cluster display, you can adjust the
contrast in the image from
Min to Max .
Driver messages
Applies to vehicles: with night vision assistant
Night vision assistant: system malfunction!
The system cannot work properly and is
switched off. See your authorized Audi dealer
for assistance.
Night vision assistant: not available
The system cannot detect properly under cur
rent conditions and is switched off temporari-
~ ~
116 Parking system
-Never use warm or hot water to remove
snow or ice from the rear view camera lens -this could cause the lens to crack!
- When cleaning the lens, never use prod
ucts that are abrasive.
Switching on and off
Applies to vehicles: with pa rk in g system plus w it h rear
view ca mera
The rear view camera switches on automati
cally together with the acoustic and visual
park assist when you put the vehicle in re vers e.
Switching on
• Switch the MMI on
• Activate
comfort or auto mode in Audi drive
select
r::!;) page 95.
• Shift into reverse or
• Press the switch
l""I in the center console
r::!;)page 113, fig. 119. A short confirmation
tone sounds and th e indicator light in the
switch lights up.
Switching between the rear view camera
and visual display
• Press the Graphic control button
r::!;) page 117 , fig . 12 S @ to see the visual
display .
• Press the
Rearview control button to see
the rear view camera image
r::!;) page 113,
fig . 120 .
Switching off
• Drive faster than 6 mph (10 km/h), or
• press the switch
I"" I or
• switch
off the ignition.
A WARNING
-The MMI display cannot show, or cannot
adequately show, certain objects (such as
small posts or grating), recesses in the
ground and protruding parts on another
car.
- Only use the rear view camera to assist
you if it shows a good, clear picture. For
example, the image may be affected by the sun shining into the lens, dirt on the
lens or if there is a defect .
- Use the rear view camera only with the
rear lid completely closed. Make sure any
objects you may have mounted on the
rear lid do not block the rear view cam
era .
(!) Tips
-The sensors must be kept clean and free
of snow and ice for the park assist to op
erate.
- If your vehicle is near an obstacle, an ad
ditional visual indicator appears in the
rearview camera image . This superim
posed image is there to help you to de
termined which area of the vehicle is af
fected.
- You can change the volume and pitch of
the signals as well as the display
r::!;) page 118.
-What appears in the display is time-de
layed .