2012 AUDI A6 wheel

192 Intelligent technology
freezing conditions ice) on the brake pads. A
few careful brake applications should dry off
the brake pads or remove any ice coatings.
The effectiveness of the brakes can be reduced
when the vehicle is driven on a salt-covered
road and the brakes are not used . Here too
,
you should clean off accumulated salt coating
from brake discs and pads with a few careful
applications of the brake
Q & .
Corrosion
There may be a tendency for dirt to build up
on the brake pads and corrosion to form on
the discs if the car is not driven regularly or
only for short trips with little use of the brakes.
If the brakes are not used frequently, or if cor­
rosion has formed on the discs, it is advisable
to clean off the pads and discs by braking
f irmly a few times from a moderately high
speed
Q & .
Faults in the brake system
If you should notice a sudden increase in
brake pedal travel, then one of the two brake
circuits may have failed
Q & .
Low brake fluid level
Malfunctions can occur in the brake system if
the brake fluid level is too low. The brake fluid
level is monitored electronically.
Brake booster
The brake booster works with vacuum pres­
sure which is created only when the engine is
running
Q & .
Brake lining wear status
Brake lining wear may be checked by visual in­
spection of the condition of the brake pads
through the openings in the wheel. If neces­
sary, the wheel may be removed for this in­
spection
Q page 258, Changing a wheel.
WARNING
- You should perform braking maneuvers
for the purpose of cleaning the brake system only if road conditions permit.
Other road users must not be put at risk -
you may cause an accident!
- Before descending a steep grade, reduce
speed and shift transmission into a lower
gear or lower driving range. Do not ride
the brakes or hold the pedal down too
long or too often . This could cause the
brakes to get hot and diminish braking
efficiency.
- Do not "ride the brakes" by resting your
foot on the pedal when you do not intend
to brake. This may cause the brakes to
overheat, premature wear and increased
stopping distance.
- Under certain climatic and operating
conditions such as passing through wa­
ter, driving in heavy rain or after washing
the vehicle, the effectiveness of the brakes can be reduced. In winter, ice can
accumulate on the brake pads, linings,
discs and drums. Carefully apply brakes
for a test. Brakes will dry and ice coat­
ings will be cleaned off after a few care­
ful brake applications.
- Driving for an extended period of time on
salt-covered roads without using your brakes can also affect braking efficiency.
Clean off accumulated salt coating from
brake discs and pads with a few careful
brake applications.
- If you damage the front spoiler, or if you
install a different spoiler, be sure the air
flow to the front brakes is not obstruct­
ed. Otherwise the brake system could
overheat reducing the effectiveness of
the entire brake system.
- Failure of one brake circuit will impair
the braking capability resulting in an in­
creased stopping distance. Avoid driving
the vehicle and have it towed to the near­
est Audi dealer or qualified workshop.
- Never let the vehicle roll to a stop with
the engine shut off.
- If the brake booster is not working, for
example when towing your vehicle, or
because the brake booster has somehow
been damaged, the brake pedal must be
~

pressed considerably harder to make up
for the lack of booster assistance.
Electro-mechanical
power assist
The electro-mechanical power assist helps
the driver when steering.
Power steering adapts electronically based on
the vehicle speed .
Indicator lights and messages
• Steering defective! Stop the vehicle
If this indicator light turns on and stays on
and this message appears, the power steering may have failed.
Do
not continue driving. See your authorized
Audi dealer or other qualified repa ir facility
for assistance.
t -r- fl Steering: System malfunction! You may
c ontinue driving
If the indicator light turns on and the mes­
sage appears, the steer ing may be more diffi­
cult to move or more sensitive than usual.
Drive slowly to your authorized Audi dealer or
qualified workshop to have the malfunction
corrected.
@ Tips
If the . or t~fl indicator light only stays
on for a short time, you may continue driv­
ing .
Driving with your
quattro ®
Applies to vehicles: with all-wheel drive
With all-wheel drive, all four wheels are driv­
en.
General information
With all-wheel drive, power is distributed to
all four wheels. This happens automatically
depending on your driving sty le and the road
conditions at the time. See also¢
page 189. Intelligent technology 193
T
he all -whee l dr ive concept is designed for
high engine power. Your vehicle is exception­
ally powerfu l and has excellent driving charac­
teristics both under normal driving conditions
and on snow and ice. Always read and follow
safety precautions¢ ,&..
Winter tires
When driving in the winter, your vehicle with
all-wheel drive has an advantage, even w ith
regular tires. In winter road conditions it may
be advisable to mount winter tires (or all-sea­
son tires) for improved driveability and brak­
ing: these tires must be mounted on
all four
wheels.
See also¢ page 250, Winter tires.
Tire chains
Where tire chains are mandatory on certain
roads, this normally also applies to vehicles
with all-wheel drive¢
page 251, Snow
chains .
Replacing wheels/tires
Vehicles with a ll-wheel drive must always
have tires of the same size. Also avoid tires
with different tread depths. For deta ils see
page ¢
page 246, New tires and replacing
tires and wheels.
Off-Road driving?
Your Audi does not have enough ground clear­
ance to be used as an off-road vehicle. It is
therefore best to avoid rough tracks and un­ even terrain as much as possible. Also refer to
¢page 197 .
A WARNING
Always adjust your dr iv ing to road and traf­
fic conditions. Do not let the extra safety
afforded by all-wheel drive tempt you into
taking extra risks.
-Although the all-wheel drive is very ef­
fective, always remember that braking
capacity is limited by tire traction. You
should therefore not drive at excessive
speeds on icy or slippery road surfaces.
•
•

194 Intelligent technolog y
-On wet road surfaces, be carefu l not to
dr ive t oo fast because the front wheels
could beg in t o slide on top of the water
(aq uaplaning). If this sho uld occur, you
will have no wa rning from a su dden in­
c rease in engine spee d as with a front­
wheel drive vehicle. A lways d rive at
speeds wh ich are suited to the road con­
di tions - ris k of crash.
Energy management
Starting ability is optimized
Energy management controls the distribution
of electrical energy and thus optimizes the
availability of electrical energy for starting
the engine.
If a vehicle with a conventional energy system
is not driven for a long period of time, the bat­
tery is d ischarged by idling current consumers
(e.g . immobilizer) . In certain circumstances it
can result in there being insufficient energy
avai lab le to start the engi ne .
Intell igent energy management in your veh i­
cle hand les the d istribution of electrical ener­
gy. Starting ab il ity is markedly improved and
the life of the battery is extended .
Basically, energy management consists of
battery diagno sis, idling curr ent manage­
ment
and dynami c energ y man agement .
Battery diagno sis
Battery diagnosis continuously determines
the state of the battery. Sensors determ ine
battery vo ltage, battery current and battery
temperature . This determ ines the current
state of charge and the powe r of the battery.
Idling current man agement
Idling current management reduces energy
consumption while the vehicle is stand ing.
W ith the ignition switched off, it contro ls the
energy supply to the various electr ical compo­
nents . Data from battery diagnosis is consid­
e red. Depend
ing on the battery's state of cha rge ,
individua l consumers are g radually turned off
to prevent excessive discharge of the battery and th us maintain starting capability.
Dynamic energy manag ement
While the vehi cle is being d riven, dynamic en ­
ergy management distributes the energy gen ­
erated accord ing to t he needs of the individ u­
al components . It regulates consumption, so
that more electrical energy is not being used
than is being generated and ensures an opti­
mal state of charge fo r the battery .
(D Tips
-But even energy management cannot
negate the limits of physics. Consider
tha t the powe r and life of a battery are
limited.
- If start ing ability is threatened , the indi­
cator light
(•i appears r:::;, page 17.
What you should know
The highest priority is given to maintaining
starting capability.
The battery is severe ly taxed in short-d istance
driv ing, in city traff ic and during the cold time
of year . Abundant electrical energy is re­
quired, but on ly a little is generated . It is also
c rit ical if the engine is not r unning and e lectri­
ca l components are tu rned on . In this in­
sta nce ene rgy is be ing consumed b ut none is
being gene ra ted.
It is in prec isely these s ituations that you will
notice ene rgy management a ctive ly regu lat­
i ng t he d istribu tion of ene rgy.
Vehicle stands for an extended period
If you do not drive your vehicle over a period
of several days or weeks, electr ica l compo­
nents a re g radually cut back or sw itched off.
T h is reduces energy consumption and ma in­
ta ins start ing capability over a longer pe riod .
Some of the convenience func tions may not
opera te, such as the interio r lights or the
power seat adjustment. The convenience
ll-

different weight distribution. Safety, perform ­
ance and economy w ill greatly depend on how
carefu lly you load yo ur trailer and operate
your rig.
B efore you actua lly tow your trailer, practice
turning, stopping and backing up in a n area
away from traffic. Keep practicing until you
have become comp letely fam iliar with the way
your veh icle- trailer comb inat ion behaves and
responds .
Backing up is d ifficu lt and requires practice .
Backing up with a tra iler genera lly requires
steer ing action opposite to that when backing
up your vehicle without a trailer .
M aintain a g reater distance between your ve­
hi cle and the one in front of you. You will need
more room to stop. To compensate for the
trailer, you will need a larger than norma l
turn ing radius.
When passing, remember that yo u cannot ac ­
celerate as fast as you normally would be­
cause of the added load . Make s ure you have
e nough roo m to pass . After passing, allow
p lenty of room fo r your tra ile r befor e chang­
in g la nes aga in.
Avoid jerky sta rts, sharp turns or rapid lane
cha nges.
(D Tips
- Do not tow a tra iler during the break- in
period of you r vehicle.
- If you t ow a trailer, your A udi may re­
quire more frequent maintenance due to
the ext ra load
¢ page 2 78 .
Parking on a slope
Do not park on a slope with a trailer. If i t can­
not be avoided, do so only after doing the fol ­
lowing:
When parking:
.. Apply the foot b rake .
.. Have someone place chocks under both the
vehicle and the trailer wheels.
Trailer towin g 203
.. W ith chocks in place, slowly release t he
brakes unt il the whee l choc ks absorb the
load .
.. Turn the whee ls towards t he curb .
.. App ly the parking brake.
.. Select the
P selector lever position .
When restarting after parking:
.. App ly the foot brake.
.. Sta rt the engine .
.. Select the
D/S selector lever position.
.. Release the park ing brake and s low ly pull
out a nd away from the wheel c hocks .
.. Stop and have someone retr ieve the wheel
chocks .
(D Tips
If you move the selector leve r of the auto­
matic transmission to
P before applying
the p arking bra ke a nd before blo cking the
whee ls, y o u m ay h ave t o use more fo rce
lat er to move the lever out of the
P p osi­
tion .
•
•

204 Cleaning and protection
Cleaning and protect ion
General information
Regular core preserves vehicle value .
Any automobile is exposed to industr ial
fumes, corrosive road salt, etc. A well cared
for Audi can look like new many years after
p ur chase . Reg ular and correct care w ill con­
tr ibute to maintain ing the beauty and valu e of
your Aud i.
Furthermore, good care may be a condition
for substantiating a warranty claim should
corrosion damage or paint defects occur.
Your auth orized Audi dealer has a variety of
dedicated vehicle-care products and can ad ­
v ise wh ich ones to use for cleaning the ext eri­
or a nd inte rior o f you r vehi cle.
Whether you use products recommended by
Aud i or other commercially ava ilable clean ing
agen ts, pleas e make sure you apply t hem cor­
r ectly .
A WARNING
-Cleani ng agen ts m ay be poi sonous. Kee p
them o ut of t he rea ch of childre n.
- H eed a ll ca ution labels.
- Always read directions on th e co ntai ner
b efore using a ny produc t. Follow the di­
rec tions caref ully.
- Most chemical cleaners a re concentrat ed
and have to be diluted.
- Use spot removing flui ds only i n well
ventila ted areas.
- Do not use gasoline, ke rosene, d iesel
fuel, nail pol is h remov er or ot her volati le
fluid s. T hey may be to xic, flammab le or
h azar dou s in other w ays. D o not was h,
w ax or dry the vehicle wi th the ig nit ion
on or the eng ine running .
- D o not cl ean t he under sides of ch assis,
f en ders, wheel cove rs , etc. without pro­
tectin g your hands and a rms. You may
c u t yourself on s harp-ed ged metal parts . -
Moisture and ice on b rakes may impair
brak ing eff ic iency
c::> page 191 , General
information.
Test the brakes ca refully
each time you wash t he vehicle .
@ For the sake of the environment
Select on ly environ mentally frien dly clean ­
i ng products. Leftover cleaning pr oducts
s hou ld not d isposed of in the househo ld
waste .
Care of exterior
Washing
Frequent washing protec ts the vehicle .
The best p rotection against environmen tal i n­
fluences is
frequ ent wash ing and waxing . H ow
often t his is requ ire d d epends o n:
- How much t he ve hicle is used
- W he re the veh icle is parked (garage, i n the
open under trees, etc .)
- The seasona l and weather conditions
- Environmental infl uences
T he longer b ird d roppings, inse cts, tree res in,
r oad and indus trial grime, t ar, soo t, ro ad salt
and other mater ials remain on the veh icle
body, the mo re lasting their destr uctive ef­
f ects w ill be . Hig h temperatures ca used by ex ­
pos ure to intense su nlight i ntens ify the c orro­
s ive effect, particular ly when hum id ity is high
as wel l.
U nder certa in circumstances,
weekly washing
may be necessary. Unde r other cond itions, a
monthly washing and waxi ng may be ade­
quate .
After the winter, the unders ide of the vehicle
sho uld be thoroughly washed, preferab ly in a
professional ca r wash.
A WARNING
-A lways read and heed all WARNINGS a nd
other info rma tion
c::> page 204.

Automatic car wash
The vehicle can be washed in almost any
modern automatic car wash .
The vehicle paint is so durable that the vehicle
can normally be washed without problems in
an automatic car wash. However, the effect on
the paint depends to a large extent on the de­
sig n of the fac ility, the filte ring of the wash
water, the type of wash and care mater ial , etc.
If the pa int has a dull appearance afte r go ing
through the car wash or is scratched, bring
this to the attention of the operator immedi­
ately. If necessary, use a different car wash.
Before going through a ca r wash, be s ure to
take the usual precautions such as closing the
windows and power roof. Factory installed an­
tennas m ust not be removed.
If you have installed additional accessor ies on
the vehicle -such as spoilers, roof rack, etc. -
it is best to ask the car was h operator if these
should be removed .
A WARNING
Always read and heed a ll WARNINGS and
other information
¢ page 204.
(D Note
- Fo ld the exterior mirro rs -flat there is a
r isk of damaging the exterio r mirrors .
Power folding exterior mirrors must not
be fo lded in or out by hand. Use the pow­
er function!
- Compare the track of your vehicle w ith
the d istance between the guide ra ils of
the facility- there is a risk of damage to
t h e wheels and tires .
- Compare the width of your vehicle wit h
the width of the tu nnel at the fac ility .
Cleaning and protec tion 205
Washing the vehicle by hand
A lot of water is needed when washing a vehi­
cle by hand .
.,. Before you start washing, make sure you
have read and u nderstood the WARNINGS
¢ .&. in General information on page 204 .
.,. First soak all dried d irt unt il it is soft, then
r inse it off.
.,. As you clean yo ur vehicle , start w it h the
roof and wor k your way down to the bottom,
using a sponge, a sponge g love or a clean
brush.
.,. Rinse the sponge o r the sponge g love often,
flushing it clean each time.
.,. Use specia l car shampoo only for
very per­
sistent d irt .
.,. Rinse the car thoroughly with water .
.,. Use a chamo is leather to gent ly w ipe the ex-
ter ior d ry.
Use a separate sponge for cleaning the
whee ls, door sills and othe r regions exposed
to road dirt . In this way, you w ill not scratch
the pa int w it h coarse par ticl es imbedded in
the sponge the next time you wash the ca r.
& WARNING ~ -
- Do not clean the underside of the chas­
sis, fenders, wheel covers , or other hard
to reach parts witho ut protecting yo ur
hands and arms . You may cut yourself on
sharp-edged metal parts.
- Always read and heed a ll WARNINGS and
other information
¢ page 204.
(D Note
- Never try to remove dirt, mud or dust if the surface of the ve hicle is dry . Never
use a dry cloth or sponge, s ince this
cou ld scratch your vehicle's paint or win ­
dows.
- Never wash your car in bright sunlight. Drops of water act as magn ifying lenses
and may damage your paint .
- When you wash your car in the winter: if you rinse your vehicle with a hose, be careful not to aim the stream of water •
•

-To he lp prevent d irt from scratching the
window, always scrape in a forward di­ rection -pushing the scraper away from
you -never back and forth.
Cast (light) alloy wheels
Cast (light) alloy wheels require special care.
.,. Wash the whee ls with a sponge o r hose
brush every other week.
.. For deep cleaning afterwards, use only a
dedicated
a ci d-fr ee cast alloy wheel cleaner .
.,. Rub a coat of
liquid w ax onto the r ims every
three month. Be sure to reach and treat all parts of the rim .
To preserve the decorative appearance of the
cast alloy wheels, some special care is neces­
sary . In add it ion to road dirt and salt, brake
dust is also corros ive. If left on for too long,
brake dust ca n cause pitting .
Use only special
acid-free cleaners formulated
for alloy rims . Safe products are available at
your Aud i dealer. Never leave the cleaner on
the r ims longer than spec ified on the label. If
not rinsed off p romptly, the acid co nta ined in
some cleane rs can attac k the th reads on the
wheel bo lts.
Never use abras ive or metal polishing clean­
i n g agents. If the protective coat ing has been
chipped, e.g. by k icked up road dirt, touch it
up as soon as possib le.
A WARNING
- Moist ure and ice on brakes may affect
braking efficiency~
page 191, General
information .
Test the brakes caref ully
each time you wash the vehicle.
- Always read and heed all WARNINGS and
other information
c:> page 204.
-
Cleaning and protec tion 209
Body cavity sealing
The body cavity sealing does not need to be
checked .
All body cav ities which could be affected by
corros io n have been thoroughly protected at
the factory .
This sealing does not require any inspection or additional treatment. If any wax should seep
out of the cavity when the ambie nt tempera­
ture is high, it can be removed with a plastic
scraper and a su itable solvent .
A WARNING
Solvents can be dangero us.
- Benz ine is flammab le and toxic. If you
use benz ine fo r removing the wax, keep
sparks, flame and lighted cigarettes
away. Never dump ben zine on the
groun d, into open streams or down sew­
age drains .
- Be s ure to obse rve all safe ty and environ­
men tal reg ulations. Fo llow all instruc­
tions on the container.
- Always read and heed all WAR NINGS and
o ther information
c:> page 204.
Chassis
Have the undercoating checked for damage
from time to time.
The lower body shell of your Aud i is also thor­
oughly p rotec ted against cor ros io n.
Any damage to the undercoat ing caused by
road hazards should be repaired promptly .
A WARNING
Too much undercoating in the wrong pla­
ces can cause a fire.
- Do not apply additional undercoating or
rustp roofing on or nea r the exhaust
manifold, exhaust pipes, catalyti c con­
ver ter or heat shields. While driving, the
substance used fo r undercoating could
overheat and cause a fire.
•
•

210 Cleaning and protec tio n
-Always read and heed all WARNINGS and
other information
c> page 204.
Exhaust tail pipes
Road salt and other corrosive materials will
damage the material in the exhaust tail pipes
if they are not cleaned regularly . Do not clean
the tail p ipes with wheel cleaner, paint pol ish,
chrome po lish or other abrasive cleaners.
C lean the tail p ipes with car ca re p roducts
that are su itable for stain less stee l.
Your author ized Audi dealer can provide clean­
ing p roducts that have been tested and ap­
p roved fo r you r vehicle.
Care of interior
Infotainment components
The MMI/RSE* display may be cleaned with a
soft cloth and commercially-ava ilable "LCD
cleaner" . The cloth should be coated lightly
when the clean ing solution when cleaning the
d isplay.
The MMI/RSE* contro ls must be cleaned first
with a brush so t hat dirt does not ente r the
un it or enter between the buttons and the
housing. Then wiping the controls with a cloth
dampened with dish detergent and water is recommended.
CJ) Note
- To avoid sc ratch ing the disp lay, you
shou ld never clean it dry.
- To prevent damage, ma ke sure fluids do
not enter the controls.
Aluminum trim
Use only n eutral-pH products to remove spots
and deposits from aluminum surfaces.
Chrome ca re products and alkaline cleaners
will attack aluminum s urfaces and can dam­
age them over time.
A WARNING
A lways read and heed all WARNINGS and
other information
c> page 204.
Fabrics and fabric coverings
Fabr ics and fabric cover ings (e .g. seats, door
trim panels, etc.) should be cleaned at regular i ntervals w ith a vacuum cleaner. This removes
su rface di rt particles which could become em ­
bedded in the fabri c through use. Steam
cleaners should not be used, because the
steam tends to p ush the dirt deeper into the
fabric and lock it there.
Normal clean ing
Generally, we recommend using a soft sponge
o r a lint-free microfiber clo th to the clean fab­
ric. Brushes shou ld only be used for carpets
and floor mats, since other fabric surfaces
could be harmed by brushes.
Norma l su rface stains can be cleaned using a
commercially available foam cleaner . Spread
the foam on the s urface of the fabric with a
soft sponge and work it in gently. Do not satu­
rate the fabric. Then pat the foam dry using
absorbent, dry cloths (e.g. m icrof iber cloth)
and vacuum it after it has dried completely.
Cle anin g sta ins
Stains caused by beverages (e .g. coffee, fruit
juice, etc.) can be treated with a mild deter­
gent solution. Apply the detergent solution
with a sponge. In the case of stubborn stains, a detergent paste can be applied directly to
the stain and worked into the fabric. After­
wards, use copious amounts of clean water to
remove the rema in ing deterge nt. Apply the
water wit h a damp clo th or sponge an d pat
the fabric dry with an abso rbent, dry cloth .
Stains from choco late or makeup should have
detergent paste (e.g. ox-gall soap) rubbed in­
to them. Afterwa rds, remove the soap with
water (damp sponge) .
Alcohol can be used to treat stains from grease, o il, lipstick or a ballpoin t pen . Melted ..,.