2012 AUDI A6 light

Vision
Sun visors
( J
Fig. 38 Sun v isor
The sun visors for the driver and passenger
can be released from their brackets and
turned toward the doors
c::> fig. 38 @.
The mirror light switches on when the cover
over the vanity mirror @opens.
Sun shad e
Applies to vehicles: with s un shade
Fig . 39 Sun s hade pulled up on th e rear w indow
Fig. 40 Cockp it: sun shade sw itc h
Rear door sunshade*
.,. Pu ll the sun shade out and attach it to the
hoo ks on the upper doo r frame
c::> fig. 39.
Clear vi sion 45
Rea r window sun shad e*
.,. To extend/retract the sun shade, press the
button~
c::> fig . 40 .
You can adjust the settings for the rea r sun
shade so the shade re tracts automatically
when you select the reverse gea r. Select:
CAR
function button > Car system s control b utton
> V ehicle settings > Automatic re ar blind >
O n. The settings are automatically stored and
ass igned to the remote control key. The sun
shade extends again as soon as the vehicle be­
gins traveling forward at a speed greater than
9 mph (15 km/h), as long as the ig nition has
not been sw itched off in the meantime.
,&. WARNING
When lowering or ra is ing the sunshade,
make sure there is nothing in its way and
that it has a free path to travel. This co uld
cause persona l inj ury .
(j} Tips
- If the sun shade is ope rated repeatedly
w ithin a short t ime, the built- in overlo ad
pro te ct io n circuit may be tripped . If th is
occurs, you will have to wait briefly be­
fore yo u can operate the shade again.
- Because of the decrease in the f lexibility
of the shade materia l at temperatures
below freezing, t he e lectr ica l circuit
w hich operates the shade shuts off when
the temperature in the vehicle falls be­
low
14 °F (-10 °C). The shade cannot be
operated until the passenger compart­
ment warms up above t his temperature .

46 Clear vis ion
Wiper and washer
system
Switching the windshield wipers on
F ig. 4 1 Windsh ie ld wipe r lever
Move the windshield wiper lever to the corre­
spond ing pos ition:
@ -Windshie ld wipers off
(I) -Rain sensor mode . The windshield w ipers
switch on once the vehicle speed exceeds ap­
proximately 2 mph (4 km/h) and it is raining.
The higher the rain sensor sens it ivity is se t
(switch @to the right), the earlier the wind ­
shield wipers react to moisture on the wi nd­
shie ld. You can deact ivate rain sensor mode in
the MMI, which w ill then activate intermi ttent
mode. Selec t:
ICAR I function bu tton > C ar s ys­
t e m s
contro l bu tton > Dri ver a ssis t > Rain
se nsor
> Off . In intermittent mode, you can
adjust the interval time using the switch @.
@-Slow wiping
@-Fast wiping
©-Single wipe. If you hold the lever in this
posi tion longer, the wipers sw itch from slow
wiping to fast wip ing .
® - Clean the windshield . The wipers wipe
one time after several seconds of driv ing to
remove water drop le ts. You can switch this
function off by mov ing the lever to position ®
within 10 seconds after the afterw ipe . The af­
terw ipe fun ct ion is react ivated the next time
you swit ch the ig nitio n on .
Clean ing the headlights . The headlight wash ­
e r system* only functions when the lights are
switched on . The headlights and the night vi- s
ion system camera * are cleaned automatical ­
ly the first time the lever is press in position
® and every 8 times it is pressed after that.
They a re also cleaned every time you ho ld the
lever in posit ion ® for longer than 8 seconds.
A WARNING
--The rain sensor is only designed to assist
and support the dr iver .
It rema ins enti re­
ly the d river's responsibility to monitor
outs ide weather cond itions and to ma n­
u a lly activate the wipe rs as soon as rai n
or drizzle reduces visibility through the
windshie ld .
- The windsh ield mu st not b e tre ate d w ith
water -repellent materials . They can in ­
crease glare under poor v isibility condi­
tions such as wetness, da rkness, or when
the sun is low on the hor izon. In addi­
tion , they can cause the w indshield w ip­
ers to chatter.
- Properly function ing windsh ield wiper
b lades are req uired for a clea r view and
safe driving
i::> page 47, Replacing
windshield wiper blades.
(D Note
- In the case of frost, check whether the
w indshield wiper blades are fr ozen to
the windsh ield . Sw itching on the wind ­
shield wipers can damage the wiper blades!
- Pr ior to us ing a car wash, the w indshield
w iper system must be sw itched off ( lever
in posit ion 0). This he lps to prevent un in­
t en tional switch ing o n and dam age to
t he winds hield wiper system.
- Do not use the w ipers to clear a frosted
w indow. Us ing the wipers as a conve n­
ient ice scraper will destroy the wiper
blades.
(D Tips
- T he windshie ld wipers are sw itched off
w hen the ig nit io n is off . Activate the
windshield wipers after the ignition is
switched back o n by moving the w ind­
shield wiper lever to any position.

-Worn or dirty windshield wiper blades
result in streaking. This can affect the
rain sensor function. Check your wind­
shield wiper blades regularly .
- The washer fluid nozzles of the wind­
shield washer system are heated at low
temperatures when the ignition is on.
- When stopping temporarily, e.g. at a
traffic light, the set speed of the wind­
shield wipers is automatically reduced by
one speed .
Replacing windshield wiper blades
Wiper blades in good condition help keep the
windshield clear.
Fig. 42 Removing winds hie ld w iper bla des
Service position
• Switch the windshield wipers
off (position
@ ¢page 46, fig. 41).
• Switch the ignition off and move the wind­
shield wiper lever to position @¢
page 46 ,
fig. 41.
Or
• Select in the MMI: !CAR !function button>
Car systems control button > Servicing &
checks > Wiper service position > On. The
windshield wipers move into the service po­
sition.
Removing the wiper blade
• Fold the windshield wiper arm away from
the windshield.
• Press the locking knob@¢
fig. 42 on the
wiper blade . Hold the wiper blade firmly.
• Remove the wiper blade in the direction of
the arrow.
Clear vision 4 7
Installing the wiper blade
• Insert the new wiper blade into the mount
on the wiper arm @unti l you hear it latch
into place.
• Place the wiper arm back on the windshield.
• Switch the ignition on.
• Press the windshield wiper lever.
Or • Select:
I CAR ! function button > Car systems
control button > Servicing & checks > Wiper
service position
> Off.
.&_ WARNING
- If the windshield wipers smear the wind­
shield, clean the wiper blades with wind­
shield washer fluid. If the wiper blades
are extremely dirty, you can also clean
them with a soft sponge or cloth.
- For your safety, you should replace the
wiper blades once or twice a year. See
your authorized Audi dealer for replace­
ment blades.
(D Note
-The windshie ld wiper blades must only
be folded away when in the service posi­
tion! Otherwise, you risk damaging the
paint on the hood or the windshie ld wip­
er motor.
- You should not move your vehicle or
press the windshield wiper lever when
the wiper arms are folded away from the
windshield. The windshield wipers would move back into their original position
and could damage the hood and wind­
shield .
- To help prevent damage to the wiper sys­
tem, always loosen blades which are fro­
zen to the windshield before operating
w ipers.
- To help prevent damage to wiper blades,
do not use gasoline, kerosene, paint
thinner, or other solvents on or near the
wiper blades .
- To help prevent damage to the wiper
arms or other components, do not at­
tempt to move the wipe rs by hand.

48 Clear vis ion
@ Tips
- Commercial hot waxes applied by auto­
matic car washes affect the cleanability
of the windshield.
- You can also use the service position, for
example, if you want to protect the
winds hield from icing by using a cover.
- You cannot activate the service position
when the hood is open.
Mirrors
Adjusting the exterior mirrors
Fig. 43 F orwa rd section of drive r's arm rest: power m ir­
ro r cont ro ls
T urn the knob to the desired position :
Q/P -In th is position, you can adjust the
d river's and front passenger's exter io r mirrors
by tur ning the knob in t he des ired direction.
® -The m irrors are heated depending on t he
outside temperature .
8 -The exterior mirrors fo ld in. In the MMI,
you can se lect if the m irrors fold in automat i­
cally when you lock the vehicle ¢ page
33 .
Driv er exter io r mirro r tilt function
To help yo u see the c urb when bac king into a
parking space, the surface of the mirror tilts
slightly . The knob must be in the P posit ion
for this to happen .
You can ad just the ti lted mirror s urface by
turning the knob in the desired direction.
When you move out of reverse and into anoth­
er gear, the new mirror posit ion is stored and
assigned to the key yo u are using . T
he mi rror goes back into its orig inal position
o nce you drive forward faster than 9 mph (15
km/h) or switch the ign ition off .
A WARNING
--
- Curved (i.e. conve x) m irror surfaces in­
crease your fie ld of view. Remember that
veh icles o r ot her objects w ill appea r
smalle r and farther away t han when seen
in a flat mir ror. If you use th is m irror to
estimate distances of followi ng ve hicles
when c hanging lanes, yo u cou ld estimate
incorrect ly and cause an accide nt.
(D Note
- If the m irror housing is moved uninten­
ti onally (for examp le, w hile pa rking your
veh icle), then yo u must first fold t he mir ­
ror electrically. Do not re adj ust the mir­
ror housing man ually . You co uld damage
the motor which controls the mirror .
-If you wash the vehicle in an automatic
car was h, you must fo ld the exter ior mir­
rors in to reduce the risk of damage to
the mirro rs. Never fold power folding ex­
terior mirrors* by hand. Only fo ld them
in and out using the power controls.
{I) Tips
- The exterior m irror settings are stored
w ith the memory function*
¢ page 53.
- If there is a malfunction in the electrical
system, you can sti ll adjust the exterior
m irrors by pressing the edge of the mir­
ror.
Dimming the mirrors
Fi g. 44 Auto matic d immin g rearv iew mirro r*

Manual anti-glare adju stment
"' Move the small lever (located on the bot ­
tom edge of the mirror) to the r ear.
Automaticall y dimming mirror s*
"' To dim the rearv iew mirror and both exteri­
or mirrors, press the@ button. The diode
@ turns on . The rearview and exte rior mi r­
rors dim automatically when l ight sh ines on
them, for example from h eadlights on ave­
hicle to the rear.
A WARNING
E lectrolyte flu id can leak from automatic
dimming mirrors if the glass is broken.
Electrolyte flu id can irritate skin, eyes and
resp iratory system .
- Repeated or prolonged exposure to elec­
tro lyte can cause irritation to the resp ira ­
tory system, espec ially among people
with asthma or other respiratory cond i­
tio ns. Get fresh ai r immediately by leav­
ing the vehicle or, if that is not possible,
open windows and doors all the way.
- If electrolyte gets into the eyes, flush
them tho ro ughly wi th la rge amoun ts of
clean water for at least 15 m in utes;
medica l attention is recommended .
-If elec trolyte contacts s kin, f lush affec t­
ed area with clean water for at least 15
minutes and then wash affected area
with soap and water; medical attention
is recommended . Thoroughly wash af­
fected clothing and shoes before reuse.
- If swa llowed and person is conscious,
rinse mouth w ith water for at least 15
minutes . Do not induce vom iting un less
instructed to do so by medical professio ­
nal. Get medical attention immedia tely .
(D Note
Liquid electrolyte leaking from broken mir­
ror glass will damage any p lastic surfaces
it comes in contact with . Clean up spilled
electrolyte immediately with clean water
and a sponge.
Clear vis ion 49
(D Tips
- Switching
off the dimming function of
the inside rear view mirror also deacti­
vates the automatic dimming function of the exter ior mirrors.
- The automatic dimming mirrors do not dim when the interior lighting is turned
on or the reverse gear is selected.
-Automatic d imming for the mirror only
operates properly if the light striking the
inside m irror is not hindered in any way .

54 Seats and storage
• To store a seating profi le, press the ISETI
button and then one of the memory but­
tons.
• To reca ll a seating profile , press and hold
the memory button until the seat is adjust­ ed to the stored settings .
• To sw itch the memory function fo r th e d riv­
er or front passenger off, p ress the
I OFFI
button. The word OFF lights up when the
memory fu nction is switched off. Seating
profiles will not be stored .
~ WARNING
-For safety reasons, the seat setting
should only be recalled when the vehicle
is stationary -otherwise you risk having
an acc ident.
- If necessary, you stop the process by
pressing the
! O FFI button or any of the
memory buttons.
Ashtray
Fi g. 51 Cente r console : front ashtray•
F ig. 52 Rear ashtray
Opening /closing
• To open the front ashtray, slide the cover
up . •
To close the front ash tray, press down on
the cover.
• To open the rear ashtray, tap the cover on
the rim.
Emptyin g
• To empty the front ashtray, pull it upward
and out .
• To empty the rear ashtray, press the rear
side of the cover down when it is open
q fig. 52 . The ashtray will lift up out of its
mount.
.,. To insert the ashtray aga in, press it down in­
to the mount unt il it locks i nto place .
A WARNING
Never put waste paper in the ashtray. Hot
as hes or other ho t objects in the ashtray
could se t waste paper on fi re .
Cigarette lighter
Applies to vehicles: wit h cigarette lighter
Fig . 53 Center co nsole: ciga rette lighte r
• Push the knob on the cigarette lighter in.
• Remove the cigarette lighter when it pops
out.
The socket of the c igarette lighter may be
used for 12-volt appliances
q page 55 .
A WARNING
-
The c igarette lighter or sockets and any
e lectr ica l accessories con nected to them
operate only when the ign ition is switched
on. Incorrect usage can lead to ser ious in­
j u ries o r burns. For th is reason, children
-

- Compartment in the rear center armrest
-Two mounting hooks* unde r the base of the
rear window inside the luggage compart­
ment. You can attach light objects to these
hooks. The mounting hooks are spring-load­
ed and will return to their normal position
when not in use.
A WARNING
- Always remove objects from the instru­
ment panel. Any items not stored could
sl ide aro und inside the vehicle while driv­
ing or when accelerating or when apply­
ing the brakes or when drivi ng around a
corner.
- When you are driving make sure that
anything you may have placed in the cen­
ter console or othe r storage locat ions
cannot fa ll out into the footwells. In case
of sudden braking you would not be able
to brake or accelerate.
- Always keep the l id of the compartment
for (sun)glasses* closed while driv ing to
reduce the risk of injury during a sudden
braking maneuver or in the event of an
acc ident.
- Any articles of cloth ing that you have
hung up must not interfere with the driv­
er's v iew. The coat hooks are designed
only for lightweight clothing. Never hang
any clothing w ith ha rd , pointed or heavy
objects in the pockets on the coat hooks.
During sudden braking or in an accident -
especially if the airbag is deployed -
these objects could injure any passen­
gers inside the vehicle.
- To reduce the risk o f personal injury in an
accident or sudden stop, always keep the
glove compartment closed while dr iv ing .
- Read and fo llow all WARN INGS
~ page 164, Important safety instruc­
tions on the side airbag system.
- Hang clothes in such a way that they do
not impair the driver's vision .
- The coat hooks must only be used for
lightweight clothing. Do not leave any
heavy or sharp edged objects in the pock ­
ets which may interfere with the side cur-
S ea ts a nd s to rage 57
tain airbag deployment and can ca use
personal injury in a crash .
- Do not use coat hangers for hanging
cloth ing on the coat hooks as this can in­
terfere with proper deployment of the side curta in a irbags in an acc ident.
- Do not hang heavy objects on the coat hooks, as they could cause personal in­
jury in a sudden stop.
- For strength-re lated reasons, the mount­
ing hooks can only be used to secure ob­
jects weigh ing up to 10 lb . (5 kg). Heavi­
e r objects will not be adequately secu red
- there is a r isk of injury .
(D Note
Objects located on the rear shelf that rub
against the rear window could damage the
heating wires for the rear w indow defog­
ger .
Roof rack
Description and mounting locations
Additional cargo can be carried with a roof
luggage rack .
Fig. 59 Roof rack attac hment po ints
.,. Always read and follow the instructions pro­
vided by the roof rack manufacturer when
the roof rack system must be installed .
If luggage or cargo is to be carried on the
roof, you must observe the following:
- To enhance the vehicle's streamlined design,
rain gutters have been molded into the roof.
It is not poss ible to use normal roof racks.
Only install a roof rack specifically designed .,.

62 Seat s a nd s tor ag e
Op ening th e trunk p ass-through
.. Fold the center armrest in the rea r forward
and out .
.. Pull the release handle ¢
fig. 64 and fold
down the cover of the pass -through in the
vehicle interior .
.. Open the rear lid .
.. Push the ski sack* through the opening
from the luggage compartment .
Sec uring the sk i s a ck *
.. Insert the ski sack strap@¢ fig. 65 in the
center buck le @ .
.. Pull the safety belt taut on the free end of
the belt @.
A WARNING
-The ski sack is intended only for the
t ransportation of skis and other light ob­
jects . To reduce the risk of serious per­
sonal inj ury never t ransport heavy o r
pointed objects in the ski sack .
- When brak ing rapidly o r during an acci­
dent the load cou ld be displaced and
cause injury to occupants .
- Sharp edges on the load must be covered
for protection . Always fasten the belt
tightly around the sack and its contents
¢ fig. 65.
(D Tips
- Never stow the sk i sack away when it is
still wet or damp (for example, snow
melting from skis). Allow it to dry com­
plete ly before stowing it away.
- Position skis in the ski sack with the pointed ends facing the front and ski
po les with the pointed ends facing the
rear.