2012 AUDI A6 Owners Manual

Instrument s and warning /indicator lights 23
Driver information
display
Overview
Fi g. 4 Dr iver info rmat ion system i n th e inst rum ent
clus te r
Fi g. 5 Display: exa mple of th e informat ion line
The driver informa tion sys tem contains in for ­
mat ion
@ t h at is displayed on tabs@
c::> fig. 4. The following content is possible de­
pending on vehicle equipment:
@
Tab
1
2
3
®
Content
Vehicle functions :
On-board computer c>page 24
Efficiency program* c::> page 25
Digital speedometer
Cr uise control*
c::> page 76
Adaptive cruise control and Audi
braking guard *
c> page 78
Display darkened
Indicator lights and messages
Warning when a doo r, the hood or
t he rear lid is not closed
Service interva l display
c::> page 26
Speed wa rning sy stem c::> page 76
Night vision assistant * c> page 97
--~~-
@ ®
Tab Content
4 Audio/video
Telephone* Navigation*
The second and th ird tabs are only vis ible if at
least one indicator light or message is shown
or if that system is sw itched on .
The status line © is located in the bottom
part of the d isp lay
<=> fig. 4. It displays the ex­
terior temperat ure, time, selector lever posi­
tion, trip odometer and odometer .
For some vehicle f unctions , you can access t he
trip information from the temporary memory
c> page 24 in the line© c> fig. 5.
A WARNING
-
-Never re ly e xclusively on the o utside
temperature display to determ ine if a
road surface is icy or not. Keep in m ind
that road surface s, espec ia lly br idg es
a nd overpa sses, co uld be ice co ve red and
slippe ry even at a n o utside tempe rat ure
above 41 ° F (+ S °C).
- Always remember, even if the "snow­
f la ke" sym bo l (ice warning) does not ap ­
pear in t he dis play, black ice cou ld be on
the road.
- Always red uce your spee d an d drive with
special care in cold weathe r cond itions
when t he chance of enco untering icy
road surfaces increases.
(D Tips
- At tempe ra tu res below 14 ° F (+ 5 °C ) a
snowfla ke symbol a ppears ahead of the
temperat ure display . It is intended to re­
mind the driver to pay special attention
to
ice on the road c> .&. . If the vehicle is
stationa ry, or if you a re driving at a very
low speed, the temperature shown in the
display might be slightly higher than the
actual ou ts ide temperature. This is
c au sed by the heat bei ng r adia ted fro m
th e engine.

24 Instruments and warning /indicator lights
-You can se lect the un its used for temper ­
atu re, speed and other measurements in
the MMI.
- Fo r information on the a udio/video and
navigation * functions, refer to the se pa·
r ate MMI owner's manual.
Operation
The driver information system is operated us­
ing the buttons on the multifunction steering wheel.
Fig. 6 Mult ifunct io n steer ing whee l: ope rat ing t he d riv·
er informat io n system
Fig. 7 Driver informat ion syst em : open ing t he ve hicle
funct io ns m enu
Operating concept
> Switc h the ign ition on.
> To sw itch between the tabs, press the rock·
er switch
(D to the left or right¢ fig . 6.
> To acc ess additional informat io n be low or
above, rotat e the thumbw heel @down or
u p.
> To confi rm a se le ction, press the thumb­
whee l@ .
> Press the~ button @ to open a s ubmenu
for an active tab.
> Press the button © to access a function fo r
t h e p rogrammable stee ring wheel button* .
Accessing Vehicle functions
> Select the first t ab with the ro cker swi tch
(D .
> Press the button ~@. T he Vehicle func­
tions
menu appears ¢ fig. 7.
> To se lect a menu item, turn and press t he
thumbwheel @.
Resetting values to ze ro
> Select the on-board computer / Efficiency
program
menu item in the Vehicle func­
tions
menu .
> You can now select between the long-term
memory and s hort-term memory.
• To reset the values in a memory, p ress a nd
hold the thumbwheel @for one second .
Assigning a function to the
programmable steering wheel button*
• Select: !CAR ! function b utton> (Car) * sys·
tems
co ntrol b utton > Vehicle settings >
Program steering wh eel button .
The last fu nction selected d isp lays w hen you
switch the ig nition on.
On-board computer
You can ca ll up the fo llowing information in
the on-board computer:
- Da te
- Dr iv ing t ime (h) from the short-term memo-
ry
- Average consumption in MPG ( l/100 km)
from the short-te rm memory
- Average speed i n mph ( km/h) from the
s h ort-te rm memory
- Dis tance driven i n miles (km) from t he
s hort- te rm memory
- Current f uel cons umption in MPG ( l/100
km)
- Short-te rm memory overview
- Long-te rm memory overv iew
The short-term memory collects driv ing infor­
mation from the time the ign it ion is switched .,.

Instrument s and warning /indicator lights 25
on until it is switched off. If yo u continue driv ­
ing within two hours after switching the igni­
tion off, the new val ues are included when
calculating the current tr ip informat ion.
Unlike the short-term memory, the long-term
memory is not e rased automatica lly. You can
se lect the t ime period for eval uat ing trip in ­
formation yo urself.
F or some vehicle functions, you can access the
trip information from the temporary memory
i n the line
(I) ~ page 23, fig. 5.
Efficiency program
The eff iciency p rogram can help yo u to u se
l ess fuel. I t eva luates dr iving information in
re ference to fue l consumpt ion and shows oth ­
er equipment inf luencing co nsumption as we ll
as shift recommendations.
c> page 25. Fue l
economy messages
c> page 25 provide tips
for efficient driving. The eff ic iency prog ram
uses distance and consumption data from tr ip
computer
1.
To display the efficiency program, call up Ve ­
hicle functions and select the menu option
Efficiency program . If the data are deleted in
the efficiency program , those values are also
reset in trip computer.
(D Tips
- All stored va lues w ill be lost if the veh i­
cle battery is disconn ected.
- Fuel consumptions (ave rage and cu r­
ren t), range and spe ed are displayed in
m etr ic uni ts on Cana dian models .
Other equipment
Fig. 8 Tri p co mpute r: ot her eq uipment
Req uirement: The e fficiency program m ust be
displayed
~ page 25.
1-Tur n the thumbw heel u ntil th e other e quip-
men t ap pears in the display.
Ot her equ ipment t hat is c urrently affe cti ng
fuel consump tion is liste d in t he eff iciency
progr am. The disp lay sh ows up to th ree o ther
items of eq uipment @. The equ ipment using
the most fuel is listed first . If more than th ree
items us ing fuel are switched on, the equip ­
ment that is c urrently using the most fuel is
displayed .
A scale @also s hows the c urrent tota l co n­
sumption of all other equipment .
Fuel economy messages
Fig. 9 Dis play : exa m ple of a fuel eco nomy m essage
Fuel economy me ssage s are di splayed when
fuel consum ption is increased by cert ain con­
di tions. If you fo llow these fuel economy mes ­
sa ges, you ca n re duce your ve hicle's consump­
t ion o f fuel. The messages appear a utomat i­
ca lly and are only d isp layed in the efficiency
program. The fue l economy messages turn off
automat ica lly afte r a certain period of t ime .
.,. To turn an economy message off immedi-
ately after it appears, press any button on
the mult ifunct ion steering wheel.
{!) Tips
- Once yo u have tur ned a f ue l economy
m essage off, it will o nly appear agai n af­
ter yo u turn the ign itio n on again .
- The fue l economy messages are not dis­
played in every instance, but rather in in­
te rvals over a period of time.

26 Instruments and warning /indicator lights
Odometer
Fig . 10 In str ument cl uster: Odomete r an d reset but­
ton
The odometer shows yo u how many mile s
(kilome ters) yo u have driven. You c an switch
the disp lay from mi les to kilome ters and vice
ve rsa via the M MI.
Upper odometer
Th e trip odom eter shows the d istance d riven
si nce i t was last rese t.
It can be used to meas ­
u re shor t distances. The l ast d igit in di cates
1/1 0 of a m ile ( 100 mete rs) .
You can reset th e trip o dom eter to ze ro by
p re ss ing the Reset button~-
Lower odometer
The lower odometer shows the total numbe r
of m iles (k ilometers) d rive n.
Malfunction message
If t here is a ma lfunction in the instrument
cluster ,
DEF will appear in the trip odometer
d isplay area. Contact your authorized Audi
deale r to have the p roblem corrected.
Time and date display
F ig. 11 I n str ume nt cluster : cloc k an d date
You can set the time and t he date disp lay in
the MMI. Refer to the M MI owne r's manual
f or instructions.
When yo u open the driver's door, the date and
time appea r in the inst rument cluster disp lay
for 30 seconds .
Service interval display
The service interval display reminds you when
your next service is due.
Fig . 12 Instrume nt c lu ste r: Se rvice inte rval disp lay
The schedule for the next o il change or inspec­
tion is ca lculated automatically and disp layed
accord ingly . Th e d isp lay works in two stages:
Service reminder
30 days be fore the next service is d ue, a serv ­
ice reminder appears in the display when you
switch the ign ition on
¢ fig. 12.
After about 5 seconds the display switches
back to norma l. The distance and time re­
mai ning are updated each t ime the ignit io n is
switched on until the date due for service is
r eached.
Service due
When the due date for se rvice is reached, the
message
Service due! appears in the instru­
ment cluster immed iate ly after yo u sw itch the
ignition o n. Add it iona lly, a warning tone
sounds . After about 5 seconds the disp lay
switches bac k to normal.
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the MMI display by selecting
t h e service interval d isplay in the car menu.
II>

Instrument s and warning /indicator lights 2 7
Select the I CAR I func tion button > Car sy s­
tems
co ntrol button > Servicing & check s >
Service inte rval displays . In new vehicles, the
schedu le can only be called up after approx i­
mate ly S00 km.
Resetting the ser vice interval d isplay
Your authorized A udi dealer wi ll rese t the cor ­
respo nding service schedule after performing
the appropriate service on yo ur vehicle. You
also have the possibility to reset the oil
change schedule after having performed an
oil change accord ing to Audi specifications.
Select the
I CAR ! function b utton > Car sys­
tem s
control button > Servicing & checks >
Servic e int erval display s> Reset oil change
interval.
(D Note
If you disconnect the bat tery t ermina ls, no
calc ulatio ns can be made for the servi ce
interv al displ ay d uring this time and no
service remi nder w ill appear. Remembe r
that obse rving the prope r se rv ice intervals
is vita lly impo rtant to extend ing the life of
y o ur veh icle, part icu larly the eng ine, and
maintaining its va lue . Even if th e mileage
driven is low, the maximum period of one
yea r from one se rvice to the next must not
be excee ded.
@ Tips
- Do not reset t he display between o il
changes, o therw ise the display will be i n­
cor re ct.
- The informati on in the Service Reminder
r ema ins sto red even when the vehicle
batte ry is disco nnecte d.
Head-up Display
Applies to vehicles: with Head-up Disp lay
Fi g. 13 Exampl e: indica tors in th e Head -up D isp lay
Fi g. 14 In strument pa nel: k nob for the Head-up Dis­
play
T he Head- up D isplay projects certain warnings
o r se le cted information from the ass istance
systems* o r naviga tion * on t he windshie ld.
T he disp lay appea rs within t he dr ive r's fie ld o f
vision .
Switching on/off
1-Press t he knob~ to switch the Head-up
Displ ay on/off ¢
fig. 1 4.
Adjusting the height
The height of the dis p lay can be adjusted to
the individual drive r.
.. Make s ure you are seated correctly
¢page
124 .
.. Turn the knob~ to adjust the display.
Settings in the MMI
.. Se lect: I CAR I function button > Car systems
cont ro l butto n > Driver assistance > Head·
up D isplay
> Head -up Display content or
Display br ightness . ..,.

28 Instruments and warning /indicator lights
Display content
In the MMI, you c an specify which informa tion
shoul d be displayed :
- Cru ise cont ro l system*
- Nav igat ion information *
- Audi adaptive cruise control*
- Night vision assistant* (pedestrian warning)
The speed display and some of the red indica­
tor lights cannot be hidden in the MMI.
Display brightness
You can adjust the display b rightness in t he
M MI. The display bright ness decreases auto­
mat ic all y as the amo unt of light decreases.
The basic leve l of bright ness is adjusted with
the instrument illumination ¢
page 44.
(D Note
To preve nt scratches on the g lass coverin g
the Head -up Display, do not place any ob ­
jects i n the projection opening.
(D} Tips
- S ung lasses w ith pol ariza tion filters an d
u nfavorable ligh ting co ndi tions can af ­
fect the display.
- Vehicles wi th sea t memory *: yo ur Hea d­
up D isplay setting s are stored automati­
ca lly and assigne d to the remote cont ro l
key that you are using .
- A specia l w indshield is needed for the
Head-up Display funct io n.
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction In dicator Lamp (MIL) I! in
the instrument cluster is part of the On-Board
Diagnostic (OBD II) system.
The warning/indicator light illumina tes when
the ign ition is switc hed o n and goes o ut afte r
the engine starts and the idle has stab ilized .
This indicates that the MIL is working proper­
ly .
If the light does not go out after t he e ngine
is started, or illuminates wh ile you are dr iv­
i ng, a mal funct ion may exist in the eng ine sys ­
tem . If the light illuminates, t he catalytic con­
verter could be damaged .
Contin ue driving
with reduced power (avo id­
i ng s ustained high speeds and/o r rap id accel ­
erations) and have the cond ition corrected.
Co ntact your a uthorized Audi dea ler.
If the light i llum inates, the e lectronic speed
li miter may also be mal funct ion ing. Fo r more
information ¢
page 29, Electronic speed
limiter.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
¢ page 217.
On-Board Diagnostics
Fig. 15 Locat io n of Data Li nk Co nnector (D LC)
On- Boa rd Di agnost ics monitors the compo ­
nents of your emissio n contro l system . Each
monitored component in your engine system
has been ass igned a code. In case of a mal­
funct ion, the component will be identified
and t he fault stored as a code in the control
modul e memo ry.
The MIL light may also illuminate if there is a leak in the on-board fuel vapor recovery sys·
tem. If the light illumi nates afte r a refu elling,
stop the vehicle a nd make sure the fuel fille r
cap is prope rly closed ¢
page 217.
In order to make a n accurate diagnosis, the
stored data can o nly be displayed using spe­
c ial d iagnost ic equipment (generic scan tool
fu rOBD) .
~

Instruments and warning/indicator lights 29
In o rder to connect the special diagnostic
equipment, push the plug into the Data Link
Connector (DLC) . The DLC is located to the
right of the hood re lease ¢
fig. 15.
Your authorized Audi dealer or a qualified
service station can interpret the code and per­
form the necessary repair.
Electronic speed limiter
Your vehicle may be factory equipped with
tires that are rated for a maximum speed of 130 mph (210 km/h) . Thi s is less than the
maximum speed of your vehicle . To reduce the
ri sk of sudden tire failure and loss of control if
the vehicle is ope rated at excessive speeds,
your veh icle also has an electronic speed limit­
er. The electronic speed limiter prevents your
vehicle from going faster than the tire speed
rating . For more information ¢
page 246.
If the engine control unit receives faulty vehi­
cle road speed signals, the Malfunction Indi­
cator Lamp (MIL)
II will i lluminate. If this
occurs, contact the nearest author ized Audi
dea ler for assistance.
A WARNING
-
Always observe the posted speed limits
and adjust your speed to suit prevailing
road, traffic and weather conditions . Never
drive your vehicle faster than the maxi­
mum speed rating of the tires insta lled.

30 Opening and clo sing
Opening and closing
Keys
Key set
Fig . 16 Key set
@ R emot e control k ey with mechan ical
ke y
You can centrally lock and unlock your vehicle
and start the engine with the master key with
remote control. A mechanical key is integrat­
ed in the remote control key
r:::;, page 31 .
@ Eme rgency ke y
The emergency key is not intended for con­
stant use.
It should only be used in an emer­
gency. Keep it in a safe place and do not carry it on your key ring .
Key replac em ent
If you lose a key, contact your authorized Audi
dealer immediately to have the
lost key disa­
bled. Be sure to bring all your keys with you.
P er sonal c omfo rt se ttin gs
If two peop le use one vehicle, it is recom­
mended that each person always uses "their
own" master key . When the ignition is switch­
ed off or when the vehicle is locked, personal
convenience settings for the follow ing sys­
tems are stored and ass igned to the remote
maste r key.
- Automatic climate control
- Central locking system
- Amb ience light ing*
- Seat memory*
- Parking system*
- Adaptive c ruise control* - Audi side assist*
-
Aud i drive select
- Night vision assistant*
- Heated steering wheel*
The stored settings are automatically recalled
when you unlock the vehicle, when you open
the doors or w hen you switch the ignition on.
A WARNING ,~
- Do not leave your vehicle unattended . Al­
ways take your ign it ion key with you and
lo ck your vehicle. Ent ry by unauthorized
persons could endanger yo u or result in
theft or damage the vehicle .
- Do not leave ch ildren unatte nded in the
veh icle, especially with access to vehicle
keys . Unguarded access to the keys pro ­
vides children the opportunity to start the engine and/or activate vehicle sys­
tems such as the power windows, etc.
Unsupervised operation of any vehicle
system by children can result in serious
in J ur y.
(D Tips
- The operat ion of t he remote control key
can be temporarily disrupted by interfer­
ence from transm itters in the vic inity of
the vehicle working in the same frequen­
cy rang e (e .g. a cell phone, radio equ ip­
ment).
- For security reasons, rep lacement keys
are only ava ilable from Audi dealers.
- For Declaration of Compliance to United States FCC and Industry Canada reg ula­
tions
r:::;, page 281 .