2012 Acura TL key

ÛÝ
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
INTERIOR ILLUMINATION’’ and
repeat the procedure again. When this item is set to ON, you will
see some guidance messages on the
multi-inf ormation display. You can
change this setting between on and
of f . For more inf ormation on start
guidance messages, see page .
You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly.
188
Keyless Start Guidance Screens
On models with keyless access system
Multi-Inf ormation Display
110
11/01/14 18:13:10 31TK4630_115
Inst rument s and Cont rols
2012 TL

ÛÝ
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button. Press the SEL/RESET button to see
the selections. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS START GUIDANCE
SCREENS’’ and repeat the
procedure again.
Multi-Inf ormation Display
Inst rument s and Cont rols
111
11/01/14 18:13:17 31TK4630_116
2012 TL

Û
Ý ÛÝ
Memory Position Link
On models with keyless access system
When Memory Position Link is set
to ON, the driver’s seat and the
outside mirrors move to the
positions stored in memory. To
cause the memory to activate, open
the driver’s door with the remote
transmitter. On models with
keyless access system, open the
driver’s door with the remote, or
grab the door handle while
carrying the remote.
To set the memory positions, see
page .
For information on using the remote,
see page . You can choose this item to
customize f rom ‘‘POSITION
SETUP’’ by pressing the INFO ( /
) button repeatedly. Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
170
173
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
113
11/01/14 18:13:35 31TK4630_118
2012 TL

Û
Ý
ÛÝ
ÛÝ
Each time you press the INFO ( /) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. While ‘‘KEYLESS ACCESS SETUP’’
is shown, press the SEL/RESET
button to enter the customize mode. KEYLESS ACCESS BEEP KEYLESS ACCESS
LIGHT FLASH DOOR UNLOCK MODE
There are three custom settings for
the keyless access setup:
CONT INUED
On models with keyless access system
K eyless A ccess Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
115
Seepage116
.
Seepage117 .
Seepage118 .
: Press the SEL/RESET button.
: Press the INFO button ( / ).
11/01/14 18:13:50 31TK4630_120
2012 TL

Û
Ý Û
Ý Press the SEL/RESET button to see
the selections. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
To select whether the driver’s door
or all doors unlock when you open
the driver’s door with the remote or
by grabbing the door handle (while
carrying the remote), f ollow these
instructions:
You can choose this item to
customize f rom ‘‘KEYLESS ACCESS
SETUP’’ by pressing the INFO ( /
) button repeatedly. Select DRIVER DOOR or ALL
DOORS by pressing the INFO ( /
) button, then enter your selection
by pressing the SEL/RESET button. If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘DOOR
UNLOCK MODE’’ and repeat the
procedure again.
Door Unlock Mode
Multi-Inf ormation Display
116
11/01/14 18:14:01 31TK4630_121
Inst rument s and Cont rols
2012 TL

ÛÝ
Û
Ý Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
When KEYLESS ACCESS LIGHT
FLASH is set to ON, some exterior
lights blink twice when you unlock
thedoorsbygrabbingthedriver’s
door handle while carrying the
remote.
You can choose this item to
customize f rom ‘‘KEYLESS ACCESS
SETUP’’ by pressing the INFO ( /) button repeatedly.
The same exterior lights blink once
when you lock the doors by pushing
the door lock button while carrying
the remote.
Keyless Access Light Flash
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
117
11/01/14 18:14:10 31TK4630_122
2012 TL

Û
Ý
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen. When KEYLESS ACCESS BEEP is
set to ON, the beeper sounds twice
when you unlock the doors by
grabbing the drivers door handle
while carrying the remote.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS ACCESS LIGHT
FLASH’’ and repeat the procedure
again. You can choose this item to
customize f rom ‘‘KEYLESS ACCESS
SETUP’’ by pressing the INFO ( /
) button repeatedly.
When you lock the doors by pushing
the door lock button while carrying
the remote, the beeper sounds once.
Keyless Access Beep
Multi-Inf ormation Display
118
11/01/14 18:14:18 31TK4630_123
Inst rument s and Cont rols
2012 TL

ÛÝ
Press the SEL/RESET button to see
the selections.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button. If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS ACCESS BEEP’’ and
repeat the procedure again.
Multi-Inf ormation Display
Inst rument s and Cont rols
119
11/01/14 18:14:26 31TK4630_124
2012 TL