2012 ACURA RL light

µ
µ
Brightness Black Level Volume
If you are having trouble viewing
the screen in bright lighting conditions,
try increasing the brightness.
Contrast
There are 11 possible brightness
settings. To change the brightness,
say ‘‘Brightness up’’ or ‘‘Brightness
down.’’ You can also select
and change the setting
by turning the interf ace knob.There are 11 possible black level
settings. To change the black level,
say ‘‘Black level up’’ or ‘‘Black level
down.’’ You can also select
and change the setting by
turning the interf ace knob. Changes
tothedisplayareverysubtle this
is normal.Say ‘‘Volume up’’ or ‘‘Volume down.’’
There are 11 possible contrast
settings. To adjust the contrast, say
‘‘Contrast up’’ or ‘‘Contrast down.’’
You can also select and
change the setting by turning the
interf ace knob. Changes to the
display are very subtle this is
normal.You can have separate
daytime and nighttime settings f or
brightness, contrast, and black level.
Adjust each setting when the display
is in either daytime or nighttime
mode. Use the Display mode button
(see page ) to select daytime or
nighttime mode.Toadjustthevolumeof thesystem
voice, do one of these actions:
Select volume off.
If youturnthevolumeoff,
you will not hear voice command
conf irmations.Select , then change the
setting by turning the interface
knob.
298 BrightnessBlack
Level
ContrastVolume
Tip:
Compass Syst em (U.S. model wit hout navigat ion syst em)
294
NOTE:
NOTE:
11/07/20 18:38:08 31SJA670_299
ProCarManuals.com

Interf ace Dial Feedback
On
Auto
(def ault)
NoThe system always
reads what you select.
The system reads your
selection only while
the vehicle is moving.
The system does not
read your selection.
Clock Adjustment
Changing this setting allows you to
controlwhen(andif)thesystemwill
read the current selection you
choose with the interf ace dial. This
feature can minimize the need to
look at the screen while operating
the dial. The three settings are
explained in the f ollowing table. The
f actory def ault setting is .You can adjust the clock of your
system. When the battery is
disconnected or the f use f or the
compass system is removed, you
need to reset the time. See page
f or more inf ormation on setting
the clock.
The second setup screen allows you
to change the system’s voice
recognition f eedback, auto volume
f or speed, and clock settings. To
select a setup item, turn the interf ace
knob until it is highlighted, then
press ENTER to select it. 313
CONT INUED
AUTO
Set t ing Feedback L evel
Second Set up Screen
Compass Syst em (U.S. model wit hout navigat ion syst em)
Features
295
11/07/20 18:38:17 31SJA670_300
ProCarManuals.com

Verbal Reminder
This f unction allows you to turn
verbal reminder ON or OFF.
Examples of these reminders
include: To view the third setup screen, move
the interf ace selector down. To
return to the first setup screen, say
‘‘Backward,’’ or move the interface
selector to the lef t to select .
The third setup screen allows you to
change the verbal reminder. To
select a setup item, turn the interf ace
knob until it is highlighted, then
press ENTER to select it.To select or , turn the
interf ace knob to the right or lef t,
then press ENTER.A reminder to f asten the driver’s
and f ront passenger’s seat belts Driving with the trunk or a door
open Driving with the parking brake on
Compass Syst em (U.S. model wit hout navigat ion syst em)
T hird Set up Screen
BACK
ON OFF
Features
297
11/07/20 18:38:36 31SJA670_302
ProCarManuals.com

If the battery goes dead or is
disconnected f or any reason, you will
have to enter a security code into
both the audio system and the
compass system bef ore you can use
it again. If f or any reason, you lose power to
the compass system (the battery was
disconnected), the system needs to
be initialized bef ore you can use it.
Initialization requires this:
Entry of the compass system 4-
digit security code to ‘‘unlock’’ the
system.
GPS initialization. This may not be
needed depending on how long the
system was without power. Pressing the (
) button allows you to switch
display modes.
Each time you turn the ignition
switch to the ACCESSORY (I)
position, the display mode is in auto.
The screen changes between day
and night modes when you turn the
headlights on and of f .
To override the auto mode, select
either day or night mode. This can
be usef ul if you want to use the
headlights during the day. Be aware
that using day mode at night will
make the screen extremely bright.
Compass Syst em (U.S. model wit hout navigat ion syst em)
Entering the Security CodeSystem Initialization Setting Display Mode
Display
mode
298
11/07/20 18:38:45 31SJA670_303
ProCarManuals.com

Whileusingthevoicecontrol
system, all of the speakers are
muted. For models with navigation
system, ref er to the navigation
system manual.
Your vehicle has a voice control
system that allows hands-f ree
operation of the audio system, the
climate control system and some
functionsof thecompasssystem.
The voice control system uses the
TALK and BACK buttons on the
steering wheel and a microphonenear the map light on the ceiling. You
acknowledge that SOFTWARE is of
US-origin. You agree to comply with
all applicable international and
national laws that apply to the
SOFTWARE, including the U.S.
Export Administration Regulations,
as well as end-user, end-use and
country destination restrictions
issued by U.S. and other
governments.
For additional information on
exporting the SOFTWARE, see
http:
//www.microsoft.com/exporting/.
Compass Syst em (U.S. model wit hout navigat ion syst em)
Voice Control Basics EXPORT RESTRICTIONS.
304
NOTE: NOTE:
TALK BUTTON
BACK BUTTONMICROPHONE
(on the ceiling)
11/07/20 18:39:24 31SJA670_309
ProCarManuals.com

The security system helps to protect
your vehicle and valuables f rom thef t.
The horn sounds and a combination
of headlights, parking/side marker
lights, and taillights f lash if someone
attempts to break into your vehicle
or remove the audio unit. This alarm
continues f or 2 minutes, then the
system resets. To deactivate the
system bef ore the 2 minutes have
elapsed, unlock either f ront door
with the remote or the built-in key.
The security system automatically
sets 15 seconds after you lock the
doors, close the hood, and close the
trunk. For the system to activate,
you must lock the doors f rom the
outside with the remote, built-in key,
lock tab, or master door lock switch.
The security system indicator on the
instrument panel starts blinking
immediately to show you the system
is setting itself .Once the security system sets,
opening any door, the trunk, or hood
without using the built-in key or the
keyless access remote, will cause the
alarm to activate. It also activates if
the ignition switch is turned to the
ON (II) position, the audio unit is
removed f rom the dashboard, or the
wiring is cut.
With the system set, you can still
open the trunk with the remote
without triggering the alarm. Thealarm will sound if the trunk lock is
f orced, or the trunk is opened with
the trunk release button on the
driver’s door or the emergency trunk
opener.
The security system does not set if
any door, the trunk, or hood is not
f ully closed. Bef ore you leave the
vehicle, make sure the doors, trunk
and hood are securely closed.
To see if the system sets af ter you
exit the vehicle, press the LOCK
button on the keyless access remote
within f ive seconds. If the system is
set, the horn will beep once.
Do not attempt to alter this system
or add other devices to it.
Security System
Features
315
SECURITY SYSTEM INDICATOR
11/07/20 18:40:46 31SJA670_320
ProCarManuals.com

You can increase the set cruising
speed in any of these ways:You can decrease the set cruising
speed in any of these ways:
Press and hold the RES/ACCEL
button. When you reach the
desired cruising speed, release the
button.
Push on the accelerator pedal.
Accelerate to the desired cruising
speed, then press the SET/
DECEL button.Press and hold the SET/DECEL
button. Release the button when
you reach the desired speed.
To increase your speed in very
small amounts, tap the RES/
ACCEL button. Each time you do
this, the vehicle speeds up about 1
mph (1.6 km/h). Cruise control may not hold the set
speed when you are going up and
down hills. If your speed increases
going down a hill, use the brakes to
slow down. This will cancel cruise
control. On models with adaptive
cruise control (ACC), this also
causes the cruise control icon on the
multi-inf ormation display to go of f
and the cruise mode icon to come on.
To resume the set speed, press the
RES/ACCEL button. The CRUISE
CONTROLicononthemulti-
inf ormation display will come back
on.To slow down in very small
amounts, tap the SET/DECEL
button. Each time you do this,
your vehicle will slow down about
1 mph (1.6 km/h).
Tap the brake pedal lightly with
your f oot. The CRUISE
CONTROLicononthemulti-
inf ormation display will go out.
When the vehicle slows to the
desired speed, press the SET/
DECEL button.
CONT INUED
Changing the Set Speed
Cruise Control
Features
317
11/07/20 18:41:02 31SJA670_322
ProCarManuals.com

·
µ
µ The HomeLink
Universal
Transceiver built into your vehicle
canbeprogrammedtooperateupto
three remote controlled devices
around your home, such as garage
doors, lighting, or home security
systems.
Bef ore programming your
HomeLink to operate a garage door
opener, conf irm that the opener has
an external entrapment protection
system, such as an ‘‘electronic eye,’’
or other saf ety and reverse stop
f eatures.
If your garage door was
manuf actured bef ore April 1, 1982,
you may not be able to program
HomeLink to operate it. These units
do not have safety features that
cause the motor to stop and reverse
it if an obstacle is detected during
closing, increasing the risk of injury.
Do not use HomeLink with anygarage door opener that lacks saf ety
stop and reverse f eatures.
Units manuf actured between April 1,
1982 and January 1, 1993 may be
equipped with saf ety stop and
reverse f eatures. If your unit does
not have an external entrapment
protection system, an easy test to
conf irm the f unction and
perf ormance of the saf ety stop and
reverse f eature is to lay a 2 4
under the closing door. The door
should stop and reverse upon
contacting the piece of wood.
As an additional safety feature,
garage door openers manuf actured
af ter January 1, 1993 are required to
have external entrapment protection
systems, such as an electronic eye,
which detect an object obstructing
the door.
Refer to the safety information that
came with your garage door openerto test that the safety features are
f unctioning properly. If you do not
have this information, contact the
manuf acturer of the equipment.
Bef ore programming HomeLink to a
garage door or gate opener, make
sure that people and objects are out
of the way of the device to prevent
potential injury or damage.
When programming a garage door
opener, park just outside the garage.
If you just
received your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the f irst button. To do this,
press and hold the two outside
buttons on the HomeLink
transceiver for about 10 20 seconds,
until the red indicator f lashes.
Release the buttons, then proceed to
step 1. General Saf ety Inf ormation
Important Saf ety PrecautionsT raining HomeL ink
HomeL inkUniversal T ransceiver
Bef ore you begin
334
11/07/20 18:43:23 31SJA670_339
ProCarManuals.com