Page 53 of 140
6-3
6
TIPThe engine is warm when it responds normally tothe throttle with the starter (choke) turned off.EBU20291Starting a warm engine Follow the same procedure as for starting a cold
engine, with the exception that the starter (choke)
is not required when the engine is warm. Instead,
start the engine with the throttle slightly open.EBU20520Shifting This ATV has a 5-speed forward transmission. The
transmission allows you to control the amount of
power you have available at a given speed or for
starting, accelerating, climbing hills, etc.
To shift into neutral, return the throttle lever to the
closed position, apply the clutch, and then repeat-
edly depress the shift pedal until it stops.
When it stops, it will be in first gear. Raise the pedal
slightly to reach the neutral position.
EBU28111To start out and accelerate
1. Release the throttle lever, and then release
the parking brake.NOTICEECB00200Always close the throttle before shifting gears,
otherwise damage to the engine and drive trainmay result.
2. Pull the clutch lever to disengage the clutch.
3. Shift into first gear.
4. Open the throttle gradually and at the same
time, release the clutch lever slowly.1. Shift pedal
2. Neutral position
1
2
2 3 4 5N1
U33B70E0.book Page 3 Wednesday, June 11, 2008 1:38 PM
Page 71 of 140
7-13
7
WARNING
EWB01720Always open the throttle gradually and release
the clutch lever slowly. Otherwise, the ATV
could wheelie which would increase thechance of an accident.NOTICEECB00230Do not shift gears without releasing the throt-
tle. Damage to the engine or drive train may oc-cur.
When slowing down or stopping, release the throt-
tle and apply the brakes smoothly and evenly. As
you slow down, shift to a lower gear. Be sure that
the engine has sufficiently slowed before engaging
a lower gear. Improper use of the brakes or shifting
can cause the tires to lose traction, reducing con-
trol and increasing the possibility of an accident.
WARNING
EWB01560Make sure the engine has sufficiently slowed
before shifting to a lower gear. Engaging a low-
er gear when the engine speed is too highcould cause the wheels to stop rotating.TURNING YOUR ATV
To achieve maximum traction on unpaved surfac-
es, the two rear wheels are mounted solidly on one
axle and turn together at the same speed. There-
fore, unless the wheel on the inside of the turn is al-
lowed to slip or lose some traction, the ATV will
resist turning. A special turning technique must be
used to allow the ATV to make turns quickly and
easily. It is essential that this skill be learned first at
low speed.
WARNING
EWB01570Always follow proper procedures for turning
as described in this Owner’s Manual. Practice
turning at low speeds before attempting to turn
at faster speeds. Do not turn at speeds too fastfor your skills or the conditions.
As you approach a curve, slow down and begin to
turn the handlebars in the desired direction. As you
do so, put your weight on the footboard to the out-
side of the turn (opposite your desired direction)
and lean your upper body into the turn. Use the
throttle to maintain an even speed through the turn.
This maneuver will let the wheel on the inside of
the turn slip slightly, allowing the ATV to make the
turn properly.
U33B70E0.book Page 13 Wednesday, June 11, 2008 1:38 PM
Page 82 of 140
7-24
7BRAKES AND ELECTRICAL EQUIPMENT
(turn signals, horn, headlight, etc.) FOR PROP-
ER OPERATION when you come out of the wa-
ter. Do not continue to ride your ATV until you
have regained adequate braking ability. (See
page 7-19.)
U33B70E0.book Page 24 Wednesday, June 11, 2008 1:38 PM
Page 89 of 140
8-7
8
EBU28130TIPThe air filter needs more frequent service if you are riding in unusually wet or dusty areas.Hydraulic brake service
Regularly check and, if necessary, correct the brake fluid level.
Every two years replace the internal components of the brake master cylinders and calipers, and
change the brake fluid.
Every two years replace the piston seals and O-ring of the brake equalizer.Replace the brake hoses every four years and if cracked or damaged.21*Moving parts and
cablesLubricate.√√√√
22*Throttle lever hous-
ing and cableCheck operation and correct if necessary.
Check throttle cable free play and adjust if neces-
sary.
Lubricate throttle lever housing and cable.√√√√√
23*Front and rear brake
switchesCheck operation and correct if necessary.√√√√√
24*Lights and switchesCheck operation and correct if necessary.
Adjust headlight beam.√√√√√ NO. ITEMCHECK OR MAINTENANCE
JOBINITIAL EVERY
Whichev-
er comes
firstmonth136612
km
(mi)320
(200)1300
(800)2500
(1600)2500
(1600)5000
(3200)
hours 20 80 160 160 320U33B70E0.book Page 7 Wednesday, June 11, 2008 1:38 PM
Page 109 of 140
8-27
8
NOTICEECB00520When tightening the locknut, hold the adjust-
ing bolt with a wrench so that it does not turntogether with the locknut.
WARNING
EWB02090Operating with improperly serviced or adjust-
ed brakes could cause the brakes to malfunc-
tion, resulting in reduced braking
performance. This could increase the chance
of a collision or accident. After adjusting the
parking brake free play, block the rear of the
ATV off the ground and spin the rear wheels.
Check to make sure there is no brake drag. If
brake drag is noticed, perform the adjustmentagain.
EBU24740Brake light switches The operation of the brake light switches must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.
The brake light switch for the brake pedal can be
adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.TIPThe brake light switch is properly adjusted when
the brake light comes on just before braking takeseffect.
Turn the adjusting nut while holding the brake light
switch in place. To make the brake light come on
earlier, turn the adjusting nut in direction (a). To
make the brake light come on later, turn the adjust-
ing nut in direction (b). Tightening torque:
Locknut (rear brake caliper):
16 Nm (1.6 m·kgf, 11 ft·lbf)
U33B70E0.book Page 27 Wednesday, June 11, 2008 1:38 PM
Page 110 of 140
8-28
8
EBU24811Adjusting the clutch lever free play The clutch lever free play must be checked and, if
necessary, adjusted at the intervals specified in the
periodic maintenance and lubrication chart.
The clutch lever free play should measure 5.0–
10.0 mm (0.20–0.39 in) as shown. If the free play
is incorrect, adjust it as follows.1. Slide the rubber cover back.
2. Loosen the locknut at the clutch lever.
3. To increase the clutch lever free play, turn the
adjusting bolt in direction (a), and to decrease
it, turn the bolt in direction (b).
4. Tighten the locknut.
5. Slide the rubber cover to its original position.1. Brake light switch
2. Brake light switch adjusting nut
12
(b)
(a)
1. Clutch lever free play
2. Locknut
3. Clutch lever free play adjusting bolt
4. Rubber cover1
3
4
(a) (b) 2
U33B70E0.book Page 28 Wednesday, June 11, 2008 1:38 PM
Page 122 of 140
8-40
8
EBU28170Headlight beam If a headlight beam adjustment is necessary, have
a Yamaha dealer perform it.EBU25600Replacing the tail/brake light bulb If the tail/brake light bulb burns out, replace it as
follows.
1. Remove the lens by removing the screws.
2. Remove the defective bulb by pushing it in
and turning it counterclockwise.3. Insert a new bulb into the socket, push it in,
and then turn it clockwise until it stops.
4. Install the lens by installing the screws.
NOTICEECB00700Do not overtighten the screws, otherwise thelens may break.EBU28030Replacing a turn signal light bulb 1. Remove the turn signal light lens by removing
the screw.
1. Screw
1
1. Tail/brake light bulb
1
U33B70E0.book Page 40 Wednesday, June 11, 2008 1:38 PM
Page 133 of 140
10-4
10
Wheel travel:
190 mm (7.5 in)Rear suspension:Type:
Swingarm
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel:
200 mm (7.9 in)Electrical system:Ignition system:
DC. CDI
Charging system:
AC magnetoBattery:Model:
YTZ7S
Voltage, capacity:
12 V, 6.0 AhHeadlight:Bulb type:
Halogen bulbBulb voltage, wattage × quantity:Headlight:
12 V, 35.0/35.0 W × 1
Tail/brake light:
12 V, 5.0/21.0 W × 1
Front turn signal light:
12 V, 10.0 W
Rear turn signal light:
12 V, 10.0 WAuxiliary light:
12 V, 5.0 W
License plate light:
12 V, 5.0 W
Neutral indicator light:
12 V, 1.7 W × 1
High beam indicator light:
LED
Turn signal indicator light:
LED
Fuses:Main fuse:
15.0 A
Accessory fuse:
7.5 A
U33B70E0.book Page 4 Wednesday, June 11, 2008 1:38 PM
