2011 YAMAHA XT660Z engine

EAUB1561
Engine oil and oil filter
element
The engine oil level should be chec-
ked before each ride. In addition, the
oil must be changed and the oil filter
element replaced at the intervals spe-
cified in the periodic maintenance and
lubrication chart.
To check the engine oil level
1. Place the vehicle on a level surfa-
ce and hold it in an upright posi-
tion.
TIP
Make sure that the vehicle is positio-
ned straight up when checking the oil
level. A slight tilt to the side can result
in a false reading.
2. Start the engine, warm it up for
10–15 minutes, and then turn it
off.
3. Remove the oil filler cap, wipe the
dipstick clean, insert it back into
the oil filler hole (without scre-
wing it in), and then remove it
again to check the oil level.
TIP
The engine oil tank is located
inside of the frame.
The engine oil should be between
the minimum and maximum level
marks.
1. Engine oil filler cap
2. Maximum level mark
3. Minimum level mark
EWA10361
Never remove the engine oil tank
cap after high-speed operation,
otherwise hot engine oil could
spout out and cause damage or
injury. Always let the engine oil cool
down sufficiently before removing
the oil tank cap.
4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to rai-
se it to the correct level. NOTICE:
Do not operate the vehicle until
you know that the engine oil
level is sufficient.
[ECA10011]
5. Install the oil filler cap.
To change the engine oil (with or
without oil filter element
replacement)
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Remove the engine guard by
removing the screws.
1. Screw
2. Engine guard
WARNING
PERIODIC MAINTENANCE AND ADJUSTMENT
6-11
6
56P-F8199-E0 30/6/10 09:24 Página 57

3. Place an oil pan under the engine
to collect the used oil.
4. Remove the engine oil filler cap
and the drain bolt to drain the oil
from the crankcase.
1. Engine oil drain bolt (crankcase)
5. Remove the drain bolt to drain
the oil from the oil tank.
1. Engine oil drain bolt (oil tank)
6. Remove the oil filter element
drain bolt to drain the oil from the
oil filter element.
TIP
Skip steps 7–9 if the oil filter element
is not being replaced.
7. Remove the oil filter element
cover by removing the bolts.
1. Oil filter element drain bolt
2. Oil filter element cover bolt
8. Remove and replace the oil filter
element and O-rings.
TIP
Make sure that the O-rings are pro-
perly seated.
1. Oil filter element
2. O-ring
9. Install the oil filter element cover
by installing the bolts.
10. Install the oil filter element drain
bolt.
11. Tighten the oil filter element
cover bolts and the oil filter ele-
ment drain bolt to their specified
torques.
12. Install the engine oil drain bolts,
and then tighten them to their
specified torques.
Tightening torques:
Oil filter element cover bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Oil filter element drain bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-12
6
56P-F8199-E0 30/6/10 09:24 Página 58

13. Add the specified amount of the
recommended engine oil, and
then install and tighten the oil
filler cap.
ECAM1061
The engine oil tank must be filled in
2 steps. First, fill the engine oil tank
with 1.90 L (2.0 US qt, 1.67 Imp.qt)
of the recommended engine oil.
Then, start the engine, race it 5 or 6
times, turn it off, and then add the
remainder of the engine oil.
TIP
Be sure to wipe off spilled oil on any
parts after the engine and exhaust
system have cooled down.
ECA11620
In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a hig-
her quality than specified. In
addition, do not use oils labe-
led “ENERGY CONSERVING II”
or higher.
Make sure that no foreign
material enters the crankcase.
14. Start the engine, and then let it
idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the
engine off and check for the cau-
se.
15. Turn the engine off, and then
check the oil level and correct it if
necessary.16. Install the engine guard by insta-
lling the screws.
NOTICE
Recommended engine oil:
See page 8-1
Without oil filter element
replacement:
2.50 L (2.64 US qt, 2.20 Imp.qt)
With oil filter element
replacement:
2.60 L (2.75 US qt, 2.29 Imp.qt
NOTICE
Tightening torques:
Engine oil drain bolt (crankcase):
30 Nm (3.0 m·kgf, 22 ft·lbf)
Engine oil drain bolt (oil tank):
18 Nm (1.8 m·kgf, 12.9 ft·lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-13
6
56P-F8199-E0 30/6/10 09:24 Página 59

EAU20070
Coolant
The coolant level should be checked
before each ride. In addition, the coo-
lant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU20253
To check the coolant level
1. Place the vehicle on a level surface
and hold it in an upright position.
TIP
The coolant level must be chec-
ked on a cold engine since the
level varies with engine tempera-
ture.
Make sure that the vehicle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
2. Check the coolant level in the
coolant reservoir.
TIP
The coolant should be between the
minimum and maximum level marks.
1. Coolant reservoir
2. Maximum level mark
3. Minimum level mark
4. Coolant reservoir cap
3. If the coolant is at or below the
minimum level mark, remove
panel E (See page 6-8). , remove
the reservoir cap, add coolant to
the maximum level mark, and
then install the reservoir cap and
the panel. WARNING! Remove
only the coolant reservoir cap.
Never attempt to remove the
radiator cap when the engine is
hot.
[EWA15161]
NOTICE: If coolant is not avai-
lable, use distilled water or soft
tap water instead. Do not use
hard water or salt water since it
is harmful to the engine. If
water has been used instead of
coolant, replace it with coolant
as soon as possible, otherwise
the cooling system will not be
protected against frost and
corrosion. If water has been
added to the coolant, have a
Yamaha dealer check the anti-
freeze content of the coolant
as soon as possible, otherwise
the effectiveness of the coolant
will be reduced.
[ECA10472]
Coolant reservoir capacity (up to
the maximum level mark):
0.50 L (0.53 US qt, 0.44 Imp.qt)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-14
6
56P-F8199-E0 30/6/10 09:24 Página 60

EAU33031
Changing the coolant
The coolant must be changed at the
intervals specified in the periodic
maintenance and lubrication chart.
Have a Yamaha dealer change the
coolant. WARNING! Never attempt
to remove the radiator cap when
the engine is hot.
[EWA10381]EAUB1481
Replacing the air filter
element and cleaning the
check hose
The air filter element should be repla-
ced at the intervals specified in the
periodic maintenance and lubrication
chart. Replace the air filter element
more frequently if you are riding in
unusually wet or dusty areas. In addi-
tion, the air filter check hose must be
frequently checked and cleaned if
necessary.
To replace the air filter element
1. Remove the seat. (See page
3-16).
2. Remove the air filter case cover
by removing the screws.
1. Air filter case cover
2. Screw
3. Pull the air filter element out.
4. Insert a new air filter element into
the air filter case as shown.
NOTICE: Make sure that the air
filter element is properly sea-
ted in the air filter case. The
engine should never be opera-
ted without the air filter ele-
ment installed, otherwise the
piston(s) and/or cylinder(s)
may become excessively worn.
[ECA10481]
PERIODIC MAINTENANCE AND ADJUSTMENT
6-15
6
56P-F8199-E0 30/6/10 09:24 Página 61

1. Air filter element
5. Install the air filter case cover by
installing the screws.
6. Install the seat.
To clean the air filter check hose
1. Air filter check hose
2. Check hose cap
1. Check the hose on the side of the
air filter case for accumulated dirt
or water.
2. If dirt or water is visible, remove
the hose, clean it, and then install
it.EAU44734
Checking the engine idling
speed
Check the engine idling speed and, if
necessary, have it corrected by a Yamaha
dealer.
Engine idling speed:
1400–1600 r/min
PERIODIC MAINTENANCE AND ADJUSTMENT
6-16
6
56P-F8199-E0 30/6/10 09:24 Página 62

EAU21383
Checking the throttle cable
free play
1. Throttle grip free play
The throttle cable free play should
measure 3.0–5.0 mm (0.12–0.20 in) at
the inner edge of the throttle grip.
Periodically check the throttle cable
free play and, if necessary, have a
Yamaha dealer adjust it.
EAU21401
Valve clearance
The valve clearance changes with
use, resulting in improper air-fuel mix-
ture and/or engine noise. To prevent
this from occurring, the valve clearan-
ce must be adjusted by a Yamaha
dealer at the intervals specified in the
periodic maintenance and lubrication
chart.
EAU21642
Tires
To maximize the performance, durabi-
lity, and safe operation of your
motorcycle, note the following points
regarding the specified tires.
Tire air pressure
The tire air pressure should be chec-
ked and, if necessary, adjusted befo-
re each ride.
EWA10503
Operation of this vehicle with
improper tire pressure may
cause severe injury or death
from loss of control.
The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperatu-
re of the tires equals the
ambient temperature).
The tire air pressure must be
adjusted in accordance with
the riding speed and with the
total weight of rider, passenger,
cargo, and accessories appro-
ved for this model.
WARNING
PERIODIC MAINTENANCE AND ADJUSTMENT
6-17
6
56P-F8199-E0 30/6/10 09:24 Página 63

EAU22760
Drive chain slack
The drive chain slack should be chec-
ked before each ride and adjusted if
necessary.
EAU22783
To check the drive chain slack
1. Drive chain slack
1. Place the motorcycle on the
sidestand.
TIP
When checking and adjusting the dri-
ve chain slack, there should be no
weight on the motorcycle.
2. Shift the transmission into the
neutral position.3. Move the rear wheel by pushing
the motorcycle to locate the tigh-
test portion of the drive chain,
and then measure the drive chain
slack as shown.
4. If the drive chain slack is inco-
rrect, adjust it as follows.
TIP
When checking the drive chain slack,
the chain tensioner should not be tou-
ching the drive chain.
EAU34316
To adjust the drive chain slack
1. Loosen the axle nut and the lock-
nut on each side of the swin-
garm.
1. Wheel axle
2. Drive chain slack adjusting bolt
3. Locknut
4. Alignment marks
2. To tighten the drive chain, turn
the drive chain slack adjusting
bolt on each side of the swin-
garm in direction (a). To loosen
the drive chain, turn the adjusting
bolt on each side of the swin-
garm in direction (b), and then
push the rear wheel forward.
NOTICE: Improper drive chain
slack will overload the engine
as well as other vital parts of
the motorcycle and can lead to
chain slippage or breakage. To
prevent this from occurring,
keep the drive chain slack wit-
hin the specified limits.
[ECA10571]
Drive chain slack:
XT660Z 50.0-60.0 mm
(1.96-2.36 in)
XT660ZA 40.0-55.0 mm
(1.57-2.17 in)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-23
6
56P-F8199-E0 30/6/10 09:24 Página 69