2011 YAMAHA XT660Z lock

Rear brake (for XT660ZA)
1. Minimum level mark
Insufficient brake fluid may allow air
to enter the brake system, possibly
causing it to become ineffective.
Before riding, check that the brake
fluid is above the minimum level mark
and replenish if necessary. A low bra-
ke fluid level may indicate worn brake
pads and/or brake system leakage. If
the brake fluid level is low, be sure to
check the brake pads for wear and
the brake system for leakage.
TIP
For XT660ZA, the rear brake fluid
reservoir is located under the seat.
(See page 3-16).
Observe these precautions:
When checking the fluid level,
make sure that the top of the bra-
ke fluid reservoir is level.
Use only the recommended qua-
lity brake fluid, otherwise the rub-
ber seals may deteriorate, cau-
sing leakage and poor braking
performance.
Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performan-
ce.
Be careful that water or dust
does not enter the brake fluid
reservoir when refilling. Water will
significantly lower the boiling
point of the fluid and may result
in vapor lock, and dirt may clog
the ABS hydraulic unit valves.
Brake fluid may deteriorate pain-
ted surfaces or plastic parts.
Always clean up spilled fluid
immediately.
As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if
the brake fluid level goes down
suddenly, have a Yamaha dealer
check the cause.
EAU22731
Changing the brake fluid
Have a Yamaha dealer change the
brake fluid at the intervals specified in
the TIP after the periodic maintenan-
ce and lubrication chart. In addition,
have the oil seals of the master cylin-
ders and calipers as well as the brake
hoses replaced at the intervals listed
below or whenever they are damaged
or leaking.
Oil seals: Replace every two
years.
Brake hoses: Replace every four
years.
Recommended brake fluid:
DOT 4
PERIODIC MAINTENANCE AND ADJUSTMENT
6-22
6
56P-F8199-E0 30/6/10 09:24 Página 68

EAU22760
Drive chain slack
The drive chain slack should be chec-
ked before each ride and adjusted if
necessary.
EAU22783
To check the drive chain slack
1. Drive chain slack
1. Place the motorcycle on the
sidestand.
TIP
When checking and adjusting the dri-
ve chain slack, there should be no
weight on the motorcycle.
2. Shift the transmission into the
neutral position.3. Move the rear wheel by pushing
the motorcycle to locate the tigh-
test portion of the drive chain,
and then measure the drive chain
slack as shown.
4. If the drive chain slack is inco-
rrect, adjust it as follows.
TIP
When checking the drive chain slack,
the chain tensioner should not be tou-
ching the drive chain.
EAU34316
To adjust the drive chain slack
1. Loosen the axle nut and the lock-
nut on each side of the swin-
garm.
1. Wheel axle
2. Drive chain slack adjusting bolt
3. Locknut
4. Alignment marks
2. To tighten the drive chain, turn
the drive chain slack adjusting
bolt on each side of the swin-
garm in direction (a). To loosen
the drive chain, turn the adjusting
bolt on each side of the swin-
garm in direction (b), and then
push the rear wheel forward.
NOTICE: Improper drive chain
slack will overload the engine
as well as other vital parts of
the motorcycle and can lead to
chain slippage or breakage. To
prevent this from occurring,
keep the drive chain slack wit-
hin the specified limits.
[ECA10571]
Drive chain slack:
XT660Z 50.0-60.0 mm
(1.96-2.36 in)
XT660ZA 40.0-55.0 mm
(1.57-2.17 in)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-23
6
56P-F8199-E0 30/6/10 09:24 Página 69

TIP
Using the alignment marks on each
side of the swingarm, make sure that
both drive chain pullers are in the
same position for proper wheel align-
ment.
3. Tighten the axle nut, then the
locknuts to their specified tor-
ques.
EAU23025
Cleaning and lubricating the
drive chain
The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly
wear out, especially when riding in
dusty or wet areas. Service the drive
chain as follows.
ECA10583
The drive chain must be lubricated
after washing the motorcycle,
riding in the rain or riding in wet
areas.
1. Clean the drive chain with kero-
sene and a small soft brush.
NOTICE: To prevent damaging
the O-rings, do not clean the
drive chain with steam clea-
ners, high-pressure washers or
inappropriate solvents.
[ECA11121]
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive
chain with a special O-ring chain
lubricant. NOTICE: Do not use
engine oil or any other lubri-cants for the drive chain, as
they may contain substances
that could damage the O-rings.
[ECA11111]
NOTICETightening torques:
Axle nut:
16 Nm (1.6 m·kgf, 11 ft·lbf)
Locknut:
105 Nm (10.5 m·kgf, 75 ft·lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-24
6
56P-F8199-E0 30/6/10 09:24 Página 70

PERIODIC MAINTENANCE AND ADJUSTMENT
6-34
6
EAU24204
Replacing a turn signal light
bulb
1. Remove the turn signal light lens
by removing the screw.
1. Screw
2. Turn signal light lens
3. Turn signal light bulb
2. Remove the burnt-out bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw. NOTICE: Do not over-
tighten the screw, otherwise
the lens may break.
[ECA11191]EAUM2202
Replacing the license plate
light bulb
1. Remove the socket (together
with the bulb) by pulling it out.
1. License plate light bulb socket
2. License plate light bulb
2. Remove the burnt-out bulb by
pulling it out.
3. Insert a new bulb into the socket.
4. Install the socket (together with
the bulb) by pushing it in.
EAU42652
Replacing an auxiliary light
bulb
This model is equipped with two auxi-
liary lights. If an auxiliary light bulb
burns out, replace it as follows.
1. Remove panel G. (See page 6-8).
2. Remove the auxiliary light socket
(together with the bulb) by pulling
it out.
1. Auxiliary light bulb socket
2. Auxiliary light bulb
3. Remove the burnt-out bulb by
pulling it out.
4. Insert a new bulb into the socket.
56P-F8199-E0 30/6/10 09:24 Página 80

7. Retighten pinch bolt A to the spe-
cified torque.
8. Apply the brake lever several
times, and then while holding the
brake lever in, push down hard
on the handlebar several times to
check for proper fork operation.EAU44800
Rear wheelEWA14840
For the ABS model, have a Yamaha
dealer remove and install the wheel.
EAU25314
To remove the rear wheelEWA10821
To avoid injury, securely support
the vehicle so there is no danger of
it falling over.
1. Loosen the axle nut.
1. Wheel axle nut
2. Drive chain slack adjusting bolt
3. Locknut
4. Drive chain
2. Lift the rear wheel off the ground
according to the procedure on
page 6-35.
3. Remove the axle nut.
1. Wheel axle
2. Drive chain slack adjusting bolt
3. Locknut
4. Brake caliper
4. Fully loosen the locknut on each
side of the swingarm.
5. Turn the drive chain slack adjus-
ting bolts fully in direction (a) and
push the wheel forward.
6. Remove the drive chain from the
rear sprocket.
TIP
If the drive chain is difficult to
remove, remove the wheel axle
WARNING
WARNING
Tightening torques:
Wheel axle:
60 Nm (6.0 m·kgf, 44 ft·lbf)
Front wheel axle pinch bolt:
18 Nm (1.8 m·kgf, 13 ft·lbf)
Brake caliper bolt:
40 Nm (4.0 m·kgf, 29 ft·lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-37
6
56P-F8199-E0 30/6/10 09:24 Página 83

Engine overheatingEWA10400
Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the his-
sing sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
TIP
If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended
coolant as soon as possible.
Wait until the
engine has cooled.Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.
The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.
Add coolant. (See TIP.)
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
There is
leakage.
There is
no leakage.
WARNING
PERIODIC MAINTENANCE AND ADJUSTMENT
6-41
6
56P-F8199-E0 30/6/10 09:24 Página 87

INDEX
AABS (for ABS models)..............................3-12
ABS warning light (for ABS models) ..........3-5
Air filter element and check hose, replacing
and cleaning ..........................................6-15
Anti-theft alarm (optional) ..........................3-9
Auxiliary light bulb, replacing ...................6-34
BBattery......................................................6-29
Brake and clutch levers, checking and
lubricating ..............................................6-25
Brake fluid level, checking .......................6-21
Brake lever ...............................................3-11
Brake pedal ..............................................3-12
Brake pedal, checking and lubricating ....6-26
CCables, checking and lubricating ............6-25
Care............................................................7-1
Catalytic converters .................................3-16
Clutch lever ..............................................3-11
Clutch lever free play, adjusting...............6-20
Coolant.....................................................6-14
Coolant temperature warning light ............3-5
DDimmer switch .........................................3-10
Drive chain slack ......................................6-23
Drive chain, cleaning and lubricating.......6-24
EEngine break-in ..........................................5-3
Engine idling speed, checking .................6-16
Engine oil and oil filter element................6-11
Engine stop switch ..................................3-10
Engine trouble warning light ......................3-5
FFront and rear brake pads, checking ......6-21
Front fork, adjusting .................................3-17
Front fork, checking .................................6-27
Fuel ..........................................................3-14
Fuel consumption, tips for reducing ............5-
Fuel tank breather/overflow hose ............3-15
Fuel tank cap ...........................................3-13
Fuses, replacing .......................................6-31
HHandlebar switches ...................................3-9
Hazard switch ..........................................3-10
Headlight bulb, replacing .........................6-32
High beam indicator light...........................3-4
Horn switch ..............................................3-10
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-20
Immobilizer system ....................................3-1
Immobilizer system indicator light .............3-6
Indicator and warning lights ......................3-4
LLicense plate light bulb, replacing ...........6-34
MMain switch/steering lock ..........................3-2
Maintenance and lubrication, periodic ......6-4
Maintenance, emission control system .....6-3
Matte color, caution ...................................7-1
Model label ................................................9-1
Multi-function display ................................3-6
NNeutral indicator light.................................3-4
PPanels, removing and installing .................6-8Parking .......................................................5-4
Part locations .............................................2-1
Pass switch ..............................................3-10
RRear suspension, lubricating ...................6-27
SSafety information ......................................1-1
Seat ..........................................................3-16
Shift pedal ................................................3-11
Shifting .......................................................5-2
Shock absorber assembly, adjusting.......3-18
Sidestand .................................................3-19
Sidestand, checking and lubricating .......6-26
Spark plug, checking .................................6-9
Specifications.............................................8-1
Start switch ..............................................3-10
Starting the engine.....................................5-1
Steering, checking ...................................6-28
Storage.......................................................7-3
Supporting the motorcycle ......................6-35
Swingarm pivots, lubricating ...................6-27
TTail/brake light ..........................................6-33
Throttle cable free play, checking ............6-17
Tool kit ........................................................6-1
Troubleshooting .......................................6-38
Troubleshooting charts ............................6-40
Turn signal indicator light ...........................3-4
Turn signal light bulb, replacing ...............6-34
Turn signal switch ....................................3-10
VValve clearance ........................................6-17
Vehicle identification number .....................9-1
56P-F8199-E0 30/6/10 09:24 Página 97