2011 YAMAHA XT660Z clutch

PERIODIC MAINTENANCE AND ADJUSTMENT
6-4
6
EAU1770C
General maintenance and lubrication chart
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
1Air filter element• Replace.√√
2Clutch• Check operation.
• Adjust.√√ √ √ √
3*Front brake• Check operation, fluid level and
vehicle for fluid leakage.√√ √ √ √ √
• Replace brake pads. Whenever worn to the limit
4*Rear brake• Check operation, fluid level and
vehicle for fluid leakage.√√ √ √ √ √
• Replace brake pads. Whenever worn to the limit
5*Brake hoses• Check for cracks or damage.√√√ √√• Replace. Every 4 years
• Check runout, spoke tightness
6*Wheelsand for damage.√√ √ √ √
• Tighten spokes if necessary.
• Check tread depth and for
damage.
7*Tires• Replace if necessary.√√√ √√
• Check air pressure.
• Correct if necessary.
8*Wheel bearings• Check bearing for looseness or
damage.√√√ √
56P-F8199-E0 30/6/10 09:24 Página 50

PERIODIC MAINTENANCE AND ADJUSTMENT
6-5
6
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
9*Swingarm• Check operation and for
excessive play.√√√ √
• Lubricate with lithium-soap-
based grease.Every 50000 km (30000 mi)
• Check chain slack, alignment
and condition.
Every 500 km (300 mi) and after washing the motorcycle,
10Drive chain• Adjust and lubricate chain with a
special O-ring chain lubricant riding in the rain or riding in wet areas
thoroughly.
• Check bearing play and steering
11 *Steering bearingsfor roughness.√√ √ √ √
• Lubricate with lithium-soap-
based grease.Every 20000 km (12000 mi)
12 *Chassis fasteners• Make sure that all nuts, bolts and
screws are properly tightened.√√√ √√
13Brake lever pivot
shaft• Lubricate with silicone grease.√√√ √√
14Brake pedal pivot
shaft• Lubricate with silicone grease.√√√ √√
15Clutch lever pivot • Lubricate with lithium-soap-
shaftbased grease.√√√ √√
• Check operation.
16Sidestand• Lubricate with lithium-soap-√√√ √√
based grease.
17 *Sidestand switch• Check operation.√√ √ √ √ √
56P-F8199-E0 30/6/10 09:24 Página 51

13. Add the specified amount of the
recommended engine oil, and
then install and tighten the oil
filler cap.
ECAM1061
The engine oil tank must be filled in
2 steps. First, fill the engine oil tank
with 1.90 L (2.0 US qt, 1.67 Imp.qt)
of the recommended engine oil.
Then, start the engine, race it 5 or 6
times, turn it off, and then add the
remainder of the engine oil.
TIP
Be sure to wipe off spilled oil on any
parts after the engine and exhaust
system have cooled down.
ECA11620
In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a hig-
her quality than specified. In
addition, do not use oils labe-
led “ENERGY CONSERVING II”
or higher.
Make sure that no foreign
material enters the crankcase.
14. Start the engine, and then let it
idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the
engine off and check for the cau-
se.
15. Turn the engine off, and then
check the oil level and correct it if
necessary.16. Install the engine guard by insta-
lling the screws.
NOTICE
Recommended engine oil:
See page 8-1
Without oil filter element
replacement:
2.50 L (2.64 US qt, 2.20 Imp.qt)
With oil filter element
replacement:
2.60 L (2.75 US qt, 2.29 Imp.qt
NOTICE
Tightening torques:
Engine oil drain bolt (crankcase):
30 Nm (3.0 m·kgf, 22 ft·lbf)
Engine oil drain bolt (oil tank):
18 Nm (1.8 m·kgf, 12.9 ft·lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-13
6
56P-F8199-E0 30/6/10 09:24 Página 59

EAU22043
Adjusting the clutch lever
free play
The clutch lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the clutch
lever free play and, if necessary,
adjust it as follows.
1. Slide the rubber cover back at
the clutch lever.
2. Loosen the locknut.
3. To increase the clutch lever free
play, turn the adjusting bolt in
direction (a). To decrease the
clutch lever free play, turn the
adjusting bolt in direction (b).
1. Locknut (clutch lever)
2. Clutch lever free play adjusting bolt
3. Clutch lever free play
TIP
If the specified clutch lever free play
could be obtained as described abo-
ve, skip steps 4–7.
4. Fully turn the adjusting bolt at the
clutch lever in direction (a) to loo-
sen the clutch cable.
5. Loosen the locknut at the crank-
case.
6. To increase the clutch lever free
play, turn the adjusting nut in
direction (a). To decrease the
clutch lever free play, turn the
adjusting nut in direction (b).
1. Locknut (crankcase)
2. Clutch lever free play adjusting nut (crank-
case)
7. Tighten the locknut at the crank-
case.
8. Tighten the locknut at the clutch
lever and then slide the rubber
cover to its original position.
PERIODIC MAINTENANCE AND ADJUSTMENT
6-20
6
56P-F8199-E0 30/6/10 09:24 Página 66

EAU23093
Checking and lubricating the
cables
The operation of all control cables
and the condition of the cables
should be checked before each ride,
and the cables and cable ends should
be lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or repla-
ce it.
EWA10711
Damage to the outer housing of
cables may result in internal rusting
and cause interference with cable
movement. Replace damaged
cables as soon as possible to pre-
vent unsafe conditions.
EAU23142
Checking and lubricating the
brake and clutch levers
Brake lever
Clutch lever
The operation of the brake and clutch
levers should be checked before eachride, and the lever pivots should be
lubricated if necessary.Recommended lubricants:
Brake lever:
Silicone grease
Clutch lever:
Lithium-soap-based grease
Recommended lubricant:
Yamaha Chain and Cable Lube or
engine oil
WARNING
PERIODIC MAINTENANCE AND ADJUSTMENT
6-25
6
56P-F8199-E0 30/6/10 09:24 Página 71

Dimensions:Overall length:
XT660Z 2246 mm (88.42 in)
XT660ZA 2260 mm (89.0 in)
Overall width:
900 mm (35.4 in)
Overall height:
XT660Z 1477 mm (57.1 in)
XT660ZA 1450 mm (57.1 in)
Seat height:
XT660Z 896 mm (35.27 in)
XT660ZA 865 mm (34.1 in)
Wheelbase:
XT660Z 1500 mm (59.05 in)
XT660ZA 1505 mm (59.3 in)
Ground clearance:
XT660Z 260 mm (10.23 in)
XT660ZA 205 mm (8.07 in)
Minimum turning radius:
1980 mm (78.0 in)
Weight:With oil and fuel:
XT660Z 208.5 kg (459 lb)
XT660ZA 215 kg (474 lb)
Engine:Engine type:
Liquid cooled 4-stroke, SOHC
Cylinder arrangement:
Forward-inclined single cylinder
Displacement:
660 cm
3
Bore x stroke:
100.0 x 84.0 mm (3.94 x 3.31 in)Compression ratio:
10.00 :1
Starting system:
Electric starter
Lubrication system:
Dry sump
Engine oil:Recommended brand:
YAMALUBE
Type:
SAE 10W-30, SAE 10W-40, SAE 15W-40,
SAE 20W-40 or SAE 20W-50
Recommended engine oil grade:
API service SE, SF, SG type or higher,
JASO standard MA
Engine oil quantity:Without oil filter element replacement:
2.50 L (2.64 US qt, 2.20 Imp.qt)
With oil filter element replacement:
2.60 L (2.75 US qt, 2.29 Imp.qt)
Cooling system:Coolant reservoir capacity (up to the maxi-
mum level mark):
0.50 L (0.53 US qt, 0.44 Imp.qt)
Radiator capacity (including all routes):
1.20 L (1.26 US qt, 1.05 Imp.qt)
Air filter:Air filter element:
Dry element
Fuel:Recommended fuel:
Premium unleaded gasoline only
Fuel tank capacity:
23.0 L (6.08 US gal, 5.06 Imp.gal)
Fuel reserve amount:
XT660Z 6.7 L (1.76 US gal, 1.46 Imp.gal)
XT660ZA 5.8 L (1.53 US gal, 1.28 Imp.gal)
Throttle body:ID mark:
5YK2 11
Manufacturer:
MIKUNI
Spark plug(s):Manufacturer/model:
NGK/CR7E
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
Clutch:Clutch type:
Wet. multiple-disc
Transmission:Primary reduction system:
Spur gear
-20 -10 0
10 20 30
40
50 ˚C
SAE 10W-30
SAE 15W-40
SAE 20W-40
SAE 20W-50
SAE 10W-40
SAE 10W-50
SPECIFICATIONS
8-1
8
56P-F8199-E0 30/6/10 09:24 Página 92

INDEX
AABS (for ABS models)..............................3-12
ABS warning light (for ABS models) ..........3-5
Air filter element and check hose, replacing
and cleaning ..........................................6-15
Anti-theft alarm (optional) ..........................3-9
Auxiliary light bulb, replacing ...................6-34
BBattery......................................................6-29
Brake and clutch levers, checking and
lubricating ..............................................6-25
Brake fluid level, checking .......................6-21
Brake lever ...............................................3-11
Brake pedal ..............................................3-12
Brake pedal, checking and lubricating ....6-26
CCables, checking and lubricating ............6-25
Care............................................................7-1
Catalytic converters .................................3-16
Clutch lever ..............................................3-11
Clutch lever free play, adjusting...............6-20
Coolant.....................................................6-14
Coolant temperature warning light ............3-5
DDimmer switch .........................................3-10
Drive chain slack ......................................6-23
Drive chain, cleaning and lubricating.......6-24
EEngine break-in ..........................................5-3
Engine idling speed, checking .................6-16
Engine oil and oil filter element................6-11
Engine stop switch ..................................3-10
Engine trouble warning light ......................3-5
FFront and rear brake pads, checking ......6-21
Front fork, adjusting .................................3-17
Front fork, checking .................................6-27
Fuel ..........................................................3-14
Fuel consumption, tips for reducing ............5-
Fuel tank breather/overflow hose ............3-15
Fuel tank cap ...........................................3-13
Fuses, replacing .......................................6-31
HHandlebar switches ...................................3-9
Hazard switch ..........................................3-10
Headlight bulb, replacing .........................6-32
High beam indicator light...........................3-4
Horn switch ..............................................3-10
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-20
Immobilizer system ....................................3-1
Immobilizer system indicator light .............3-6
Indicator and warning lights ......................3-4
LLicense plate light bulb, replacing ...........6-34
MMain switch/steering lock ..........................3-2
Maintenance and lubrication, periodic ......6-4
Maintenance, emission control system .....6-3
Matte color, caution ...................................7-1
Model label ................................................9-1
Multi-function display ................................3-6
NNeutral indicator light.................................3-4
PPanels, removing and installing .................6-8Parking .......................................................5-4
Part locations .............................................2-1
Pass switch ..............................................3-10
RRear suspension, lubricating ...................6-27
SSafety information ......................................1-1
Seat ..........................................................3-16
Shift pedal ................................................3-11
Shifting .......................................................5-2
Shock absorber assembly, adjusting.......3-18
Sidestand .................................................3-19
Sidestand, checking and lubricating .......6-26
Spark plug, checking .................................6-9
Specifications.............................................8-1
Start switch ..............................................3-10
Starting the engine.....................................5-1
Steering, checking ...................................6-28
Storage.......................................................7-3
Supporting the motorcycle ......................6-35
Swingarm pivots, lubricating ...................6-27
TTail/brake light ..........................................6-33
Throttle cable free play, checking ............6-17
Tool kit ........................................................6-1
Troubleshooting .......................................6-38
Troubleshooting charts ............................6-40
Turn signal indicator light ...........................3-4
Turn signal light bulb, replacing ...............6-34
Turn signal switch ....................................3-10
VValve clearance ........................................6-17
Vehicle identification number .....................9-1
56P-F8199-E0 30/6/10 09:24 Página 97