Page 25 of 146
3-1
3
EBU17680
DESCRIPTION
EBU17690Left view
EBU17700Right view
1. Fuel cock
2. Throttle stop screw
3. Fuses
4. Battery
5. Rear shock absorber assembly spring preload adjusting
ring
6. Engine oil filler cap
7. Oil filter cartridge
8. V-belt cooling duct check hose
1
26
7
8
5
3,4
1. Spark arrester
2. Storage compartment and tool kit
3. Air filter case
4. Spark plug
5. Front shock absorber assembly spring preload adjusting
ring
6. Rear brake light switch
7. Brake pedal
8. V-belt case drain plug
1
2
87
6
3
4
5
U4S264E0.book Page 1 Thursday, August 5, 2010 1:24 PM
Page 26 of 146
3-2
3
EBU17712Controls and instruments
TIPThe ATV you have purchased may differ slightly
from the figures shown in this manual.
1. Rear brake lever
2. Handlebar switches
3. Starter (choke)
4. Parking brake lock plate
5. Horn switch
6. Drive select lever
7. Speedometer
8. Main switch
9. Fuel tank cap
10.On-Command four-wheel-drive/differential gear lock
switch
11.Throttle lever
12.Front brake leverU4S264E0.book Page 2 Thursday, August 5, 2010 1:24 PM
Page 27 of 146
4-1
4
EBU17733
INSTRUMENT AND CONTROL FUNCTIONS
EBU17770Main switch The positions of the main switch are as follows:
ON
All electrical systems are supplied with power. The
headlights, meter lighting and taillight come on
when the light switch is on, and the engine can be
started. The key cannot be removed.
OFF
All electrical systems are off. The key can be re-
moved.
1. Main switch
U4S264E0.book Page 1 Thursday, August 5, 2010 1:24 PM
Page 28 of 146

4-2
4
EBU17815Indicator lights and warning light EBU17870Neutral indicator light “NEUTRAL”
This indicator light comes on when the transmis-
sion is in the neutral position.EBU28331Reverse indicator light “REVERSE”
This indicator light comes on when the transmis-
sion is in the reverse position.Furthermore, this indicator light flashes:
when the override switch is being pushed,when the engine is being raced for 10 seconds
or more.TIPIf the indicator light flashes under any other circum-
stances or the speedometer does not show the
speed while riding, have a Yamaha dealer check
the speed sensor circuit.EBU26932Oil temperature warning light“”
This warning light comes on when the engine over-
heats. When this occurs, stop the engine as soon
as it is safe to do so, and allow it to cool.
The electrical circuit of the warning light can be
checked by turning the key to “ON”, with the engine
stop switch set to“”, and then pushing the start
switch.
If the warning light does not come on while the start
switch is being pushed, or if the warning light re-
mains on after the start switch is released, have a
Yamaha dealer check the electrical circuit.
If the warning light stays on when the engine is
cool, have a Yamaha dealer check the electrical
circuit.
1. Reverse indicator light “REVERSE”
2. Neutral indicator light “NEUTRAL”
3. Oil temperature warning light“”
4. On-Command differential gear lock indicator light“”
5. On-Command four-wheel-drive indicator light“”U4S264E0.book Page 2 Thursday, August 5, 2010 1:24 PM
Page 29 of 146

4-3
4
NOTICEECB00010The engine may overheat if the ATV is over-
loaded. In this case, reduce the load to spec-
ification.Start the engine after making sure that the
warning light is out. Continuous use while
the warning light is on may cause damage to
the engine.EBU29611On-Command four-wheel-drive indicator
light“” and On-Command differential gear
lock indicator light“”
The On-Command four-wheel-drive indicator
light“” comes on when the On-Command four-
wheel-drive switch is set to the “4WD” position.
The On-Command differential gear lock indicator
light“” and the On-Command four-wheel-drive
indicator light“” come on when the On-Com-
mand differential gear lock switch is set to the
“LOCK” position.
TIPDue to the synchronizing mechanism in the differ-
ential gear case, the light may not come on until
the ATV starts moving.EBU18022Speedometer This speedometer is equipped with an odometer
and a tripmeter. The tripmeter can be reset to zero
with the reset knob. Use the tripmeter to estimate
how far you can ride on a tank of fuel before going
to reserve. This information will enable you to plan
fuel stops in the future.
U4S264E0.book Page 3 Thursday, August 5, 2010 1:24 PM
Page 30 of 146
4-4
4
EBU18061Handlebar switches EBU18080Engine stop switch“/”
Set this switch to“” before starting the engine.
The engine stop switch controls the ignition and
stops the engine when it is running. Use this switch
to stop the engine in an emergency situation. The
engine will not start or run when this switch is set
to“”.
1. Reset knob
2. Speedometer
3. Odometer
4. Tripmeter
1. Light switch“/ /OFF”
2. Start switch“”
3. Engine stop switch“/”
4. Override switch “OVERRIDE”
5. Horn switch“”
U4S264E0.book Page 4 Thursday, August 5, 2010 1:24 PM
Page 31 of 146

4-5
4
EBU18101Start switch“”
Push this switch to crank the engine with the start-
er. See the starting instructions on page 6-1 prior
to starting the engine.EBU18161Light switch“//OFF”
Set this switch to“” to turn on the low beams,
the taillight and the meter lighting. Set the switch
to“” to turn on the high beams, the taillight and
the meter lighting. Set the switch to “OFF” to turn
off all the lights.NOTICEECB00041Do not use the headlights with the engine
turned off for an extended period of time, oth-
erwise the battery may discharge to the point
that the starter motor will not operate properly.
If this should happen, remove the battery and
recharge it. See page 8-41 for battery charging
information.EBU18170Horn switch“”
Press the switch to sound the horn.
EBU28510Override switch “OVERRIDE”
Top speed is normally limited when operating in
differential gear lock. If conditions require more en-
gine power when riding forward, push and hold this
switch to override the differential gear lock speed
limiting function. (See page 4-7.) Releasing the
switch restores the speed limiting function.
While the override switch is pushed, the reverse in-
dicator light “REVERSE” will flash.1. Override switch “OVERRIDE”
U4S264E0.book Page 5 Thursday, August 5, 2010 1:24 PM
Page 32 of 146

4-6
4
WARNING
EWB00150Always ride at a slow speed when the ATV is in
four-wheel-drive differential gear lock, and al-
low extra time and distance for maneuvers.
All wheels turn at the same speed when the dif-
ferential is locked, so it takes more effort to
turn the ATV. The effort needed to turn increas-
es with the riding speed. You may lose control
and have an accident if you cannot make a
sharp enough turn for the speed you are trav-
eling.EBU28432On-Command four-wheel-drive switch
“2WD”/“4WD”
WARNING
EWB00163Always stop the ATV before changing from
two-wheel drive to four-wheel drive and vice
versa. The ATV handles differently in two-
wheel drive than in four-wheel drive in some
circumstances. Changing from two-wheel
drive to four-wheel drive or vice versa while
moving may cause the ATV to unexpectedlyhandle differently. This could distract the oper-
ator and increase the risk of losing control and
of causing an accident.
This ATV is equipped with a switch to change from
two-wheel drive to four-wheel drive and vice versa.
Select the appropriate drive according to the ter-
rain and the conditions.“2WD” (two-wheel drive): Power is supplied to
the rear wheels.“4WD” (four-wheel drive): Power is supplied to
the rear and front wheels.
To change from two-wheel drive to four-wheel
drive, stop the ATV and push the switch in to the
“4WD” position. The four-wheel-drive indicator
light“” comes on.
To change from four-wheel drive to two-wheel
drive, stop the ATV and push the switch in to the
“2WD” position.
U4S264E0.book Page 6 Thursday, August 5, 2010 1:24 PM