2011 YAMAHA GRIZZLY 350 stop start

7-23
7 WHAT TO DO...

If your ATV doesn’t turn when you want it to:
Bring the ATV to a stop and practice the turning
maneuvers again. Be sure you are putting your
weight on the footboard to the outside of the
turn. Position your weight over the front wheels
for better control. (See page 7-12.)
If your ATV begins to tip while turning:
Lean more into the turn to regain balance. If nec-
essary, gradually let off the throttle and/or steer
to the outside of the turn. (See page 7-12.)
If your ATV starts to slide sideways:
Steer in the direction of the slide if you have the
room. Applying the brakes or accelerating is not
recommended until you have corrected the
slide. (See page 7-21.)
If your ATV can’t make it up a hill you are trying
to climb:
Turn the ATV around if you still have forward
speed. If not, stop, dismount on the uphill side of
the ATV and physically turn the ATV around. If
the ATV starts to slip backwards, DO NOT USE
THE REAR BRAKE IF THE ATV IS IN “2WD” –
the ATV may tip over on top of you. Dismount
the ATV on the uphill side. (See page 7-13.)

If your ATV is traversing a sloping surface:
Be sure to ride with your weight positioned to-
wards the uphill side of the ATV to maintain
proper balance. If the ATV starts to tip, steer
down the hill (if there are no obstacles in your
way) to regain balance. If you discover that the
ATV is going to tip over, dismount on the uphill
side. (See page 7-17.)
If your ATV encounters shallow water:
Ride slowly and carefully through slow moving
water, watching for obstacles. Be sure to let wa-
ter drain from the ATV and CHECK YOUR
BRAKES FOR PROPER OPERATION when
you come out of the water. Do not continue to
ride your ATV until you have regained adequate
braking ability. (See page 7-18.)
U4S264E0.book Page 23 Thursday, August 5, 2010 1:24 PM

8-27
8
TIPA diagnostic tachometer is needed to make this
adjustment.1. Start the engine and warm it up.TIPThe engine is warm when it quickly responds to the
throttle.2. Attach the tachometer to the spark plug lead.
3. Check the engine idling speed and, if neces-
sary, adjust it to specification by turning the
throttle stop screw at the carburetor. To in-
crease the engine idling speed, turn the throt-
tle stop screw in direction (a), and to decrease
it, turn the screw in direction (b).
TIPIf the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.EBU24047Adjusting the throttle lever free play The throttle lever free play should be checked and,
if necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.1. Throttle stop screwEngine idling speed:
1450–1550 r/min
U4S264E0.book Page 27 Thursday, August 5, 2010 1:24 PM

9-1
9
EBU25860
CLEANING AND STORAGE
EBU25881Cleaning Frequent, thorough cleaning of your ATV will not
only enhance its appearance but will improve its
general performance and extend the useful life of
many components.
1. Before cleaning the ATV:
a. Block off the end of the exhaust pipe to
prevent water entry. A plastic bag and
strong rubber band may be used.
b. Make sure the spark plug and all filler caps
are properly installed.
2. If the engine case is excessively greasy, apply
degreaser with a paint brush. Do not apply de-
greaser to the wheel axles.
3. Rinse the dirt and degreaser off with a garden
hose. Use only enough pressure to do the job.
WARNING! Wet brakes may have reduced
stopping ability, increasing the chance of
an accident. Test the brakes after washing.
Apply the brakes several times at slow
speeds to let friction dry out the linings.
[EWB02311]
NOTICE: Excessive water pressure
may cause water seepage and deteriora-tion of wheel bearings, brakes, transmis-
sion seals and electrical devices. Many
expensive repair bills have resulted from
improper high-pressure detergent applica-
tions such as those available in coin-oper-
ated car washers.
[ECB00711]
4. Once most of the dirt has been hosed off,
wash all surfaces with warm water and mild,
detergent-type soap. An old toothbrush or bot-
tle brush is handy for hard-to-reach places.
5. Rinse the ATV off immediately with clean wa-
ter and dry all surfaces with a chamois, clean
towel or soft absorbing cloth.
6. Clean the seat with a vinyl upholstery cleaner
to keep the cover pliable and glossy.
7. Automotive type wax may be applied to all
painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
abrasives which may mar the paint or protec-
tive finish. When finished cleaning, start the
engine and let it idle for several minutes.
U4S264E0.book Page 1 Thursday, August 5, 2010 1:24 PM

INDEX
AAccessories and loading ................................................ 6-6
Air filter element, cleaning ............................................ 8-21
Axle boots .................................................................... 8-36BBattery .......................................................................... 8-41
Brake fluid, changing .................................................... 8-31
Brake fluid level, checking ............................................ 8-30
Brake lever free play, checking the front ...................... 8-32
Brake lever, front .......................................................... 4-10
Brake levers, checking and lubricating ......................... 8-38
Brake light switches ..................................................... 8-37
Brake pads and friction plates, checking ...................... 8-29
Brake pedal and rear brake lever ................................. 4-11
Brake pedal, checking and lubricating ......................... 8-39
Brakes .......................................................................... 8-29
Brakes, front and rear .................................................... 5-3CCables, checking and lubricating ................................. 8-37
Carburetor, adjusting .................................................... 8-26
Carrier, front ................................................................. 4-19
Carrier, rear .................................................................. 4-19
Chassis fasteners ........................................................... 5-6
Cleaning ......................................................................... 9-1DDifferential gear oil ................................................ 5-3, 8-18
Drive select lever .......................................................... 4-12
Drive select lever and driving in reverse ........................ 6-3Drive select lever safety system cable, adjusting ......... 8-29
Drive shaft universal joint, lubricating ........................... 8-40
EEngine break-in .............................................................. 6-4
Engine, cold start ........................................................... 6-1
Engine idling speed ...................................................... 8-26
Engine oil ....................................................................... 5-3
Engine oil and oil filter cartridge ................................... 8-12
Engine, starting a warm ................................................. 6-3
Engine stop switch ......................................................... 4-4FFinal gear oil .......................................................... 5-3, 8-16
Four-wheel-drive indicator light ...................................... 4-3
Fuel ....................................................................... 4-13, 5-3
Fuel cock ...................................................................... 4-15
Fuel tank cap ................................................................ 4-13
Fuses, replacing ........................................................... 8-44HHandlebar switches ........................................................ 4-4
Headlight beam, adjusting ............................................ 8-47
Headlight bulb, replacing .............................................. 8-45
Horn switch .................................................................... 4-5IIdentification numbers .................................................. 11-1
Indicator lights and warning light .................................... 4-2
Instruments, lights and switches .................................... 5-6LLabel locations ............................................................... 1-1
U4S264E0.book Page 1 Thursday, August 5, 2010 1:24 PM