2011 TOYOTA AYGO brakes

KEYS AND DOORS31
MS12022b
To open the rear window, pull the latch
handle toward you and swing it fully
out.
MS12034
Push the latch handle to securely lock the
latch as shown in the illustration.
CAUTION
Be sure not to put any body parts,
such as hands, out of the rear win-
dows while the vehicle is in motion.
Doing so could be very dangerous
because serious injury may result
from collisions or when the brakes
are suddenly applied.
AYGO WE 99E37E11 02.18
Rear windows (5−door
models only)

GAUGES, METERS AND SERVICE REMINDER INDICATORS129
(a) Brake System Warning Light
This light comes on in the following cases
when the engine switch is in the “ON”
position.
DWhen the parking brake is applied...
This light comes on for a few seconds
when the engine switch is turned to the
“ON” position even after the parking brake
is released.
DWhen the brake fluid level is low...
CAUTION
It is dangerous to continue driving
normally when the brake fluid level is
low.
Have your vehicle checked at any au-
thorized Toyota dealer or repairer, or
another duly qualified and equipped
professional, in the following cases:
DThe light does not come on even if the
parking brake is applied when the en-
gine switch is in the “ON” position.
DThe light does not come on even if the
engine switch is turned on with the
parking brake released.
A warning light turning on briefly during
operation does not indicate a problem.
CAUTION
If either of the following conditions
occurs, immediately stop your vehicle
at a safe place and contact any au-
thorized Toyota dealer or repairer, or
another duly qualified and equipped
professional.
DThe light does not turn off even
after the parking brake is released
while the engine is running.
In this case, the brakes may not
work properly and your stopping
distance will become longer. De-
press the brake pedal firmly and
bring the vehicle to an immediate
stop.
DThe brake system warning light re-
mains on together with the “ABS”
warning light.
In this case, not only the anti−lock
brake system will fail but also the
vehicle will become extremely un-
stable during braking.
(b) Driver ’s Seat Belt Reminder Light
and Buzzer
The light and buzzer act as a reminder to
buckle up the driver ’s seat belt.
Once the engine switch is turned to “ON”
or “START”, the reminder light flashes if
the driver ’s seat belt is not fastened. Un-
less the driver fastens the belt, the light
continues flashing.
If the vehicle speed rises above 20 km/h
(12 mph) with the seat belt unfastened,
the buzzer will sound for 30 seconds.
Then, if the seat belt is still unfastened,
the buzzer will sound in a different tone
for 90 more seconds. Even if the vehicle
speed drops below 20 km/h (12 mph), the
buzzer will continue to sound. To stop the
buzzer, fasten the seat belt. If the buzzer
still sounds, make sure the front passen-
ger ’s seat belt is fastened.
AYGO WE 99E37E11 02.18

GAUGES, METERS AND SERVICE REMINDER INDICATORS133
If either of the following conditions
occurs, this indicates a malfunction
somewhere in the components moni-
tored by the warning light system.
Contact any authorized Toyota dealer or
repairer, or another duly qualified and
equipped professional, as soon as
possible to service the vehicle.
DThe light does not come on when the
engine switch is turned to the “ON”
position, or remains on.
DThe light comes on while you are driv-
ing.
A warning light turning on briefly during
operation does not indicate a problem.
CAUTION
If the “ABS” warning light remains on
together with the brake system warn-
ing light, immediately stop your ve-
hicle at a safe place and contact any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional.
In this case, not only the anti−lock
brake system will fail but also the
vehicle will become extremely unsta-
ble during braking.
Vehicles with vehicle stability control sys-
tem—
The light comes on when the engine
switch is turned to the “ON” position. If
the anti−lock brake system and the brake
assist system work properly, the light
turns off after a few seconds. Thereafter,
if either of the system malfunctions, the
light comes on again.
When the “ABS” warning light is on (and
the brake system warning light is off), the
anti−lock brake system, the brake assist
system, the traction control system and
the vehicle stability control system do not
operate, but the brakesystem stilloper-
ates conventionally.When the “ABS” warning light is on (and
the brake system warning light is off), the
anti−lock brake systemdoes not operate
so that the wheels could lock up during a
sudden braking or braking on slippery
road surfaces.
If either of the following conditions
occurs, this indicates a malfunction
somewhere in the components moni-
tored by the warning light system,
contact any authorized Toyota dealer or
repairer, or another duly qualified and
equipped professional, as soon as
possible to service the vehicle.
DThe light does not come on when the
engine switch is turned to the “ON”
position, or remains on.
DThe light comes on while you are driv-
ing.
A warning light turning on briefly during
operation does not indicate a problem.
CAUTION
If the “ABS” warning light remains on
together with the brake system warn-
ing light, immediately stop your ve-
hicle at a safe place and contact any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional.
In this case, not only the anti−lock
brake system will fail but also the
vehicle will become extremely unsta-
ble during braking.
(l) “VSC” Warning Light
This light warns that there is a problem
somewhere in the vehicle stability control
system or traction control system.
The light will come on when the engine
switch is turned to the “ON” position and
will go off after a few seconds.
AYGO WE 99E37E11 02.18

144ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
(e) Stopping
The vehicle can be stopped by depressing
the brake pedal regardless of the gear
position. This is because the clutch is
automatically disengaged to prevent the
engine from stopping. If the shift lever is
in the “E” position, the gear will be down-
shifted to 1st when the vehicle stops.
In case the driver ’s door is opened with
the gear in “E”, “M” or “R” position and
without depressing the brake pedal, a
warning buzzer (long pulse sound) will
sound.
When the engine switch is “ON” and the
vehicle speed is slower than 9 km/h (5
mph), if the shift lever is in “N” position
and the brake pedal is released (not de-
pressed) for approximately 2 seconds, the
shift lever will be locked.
Shift lock system is designed for prevent-
ing the vehicle from starting off by the
unintended activation of the starting assist
system.
The shift lock can be released by de-
pressing the brake pedal without holding
the shift lever.
CAUTION
DWhen stopping, for example, at a
traffic light, be sure to depress the
brake pedal firmly. For your safety,
apply parking brake, too, when
stopping on a hill.
DWhen racing the engine, make sure
that the gear position is in the “N”
position by the gear position indica-
tor. In case the accelerator is oper-
ated with the gear in any other
position, the vehicle may move re-
sulting in an unexpected accident.
DDo not leave your vehicle unat-
tended while the engine is running.
DWhen leaving the vehicle, stop the
engine and park the vehicle with
the gear engaged. In case you need
to leave the vehicle with the engine
running, apply the parking brakes
firmly, and shift the shift lever in
the “N” position. When the driver ’s
door is opened with the shift lever
in the “E” position while stopping
with the engine running, warning
buzzer (long pulse sound) will
sound. If this happens on a hill
when starting off the vehicle, the
vehicle may move unexpectedly and
cause an accident.
11 02.18
AYGO WE 99E37E

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE147
MS16010a
(a) Upshift and downshift
Upshifting
Pull the shift lever to the “+” direction
and release it. Every time the lever is
operated, the transmission is upshifted
1 step in the order of 1st→2nd→
3rd→4th→5th gear.
Downshifting
Push the shift lever to the “−” direction
and release it. Every time the lever is
operated, the transmission is down-
shifted in the order of 5th→4th→
3rd→2nd→1st gear.
DTo shift down smoothly, the engine
runs fast in some cases. This is done
intentionally by the system and is not
a malfunction.
DWhen driving down a hill, downshift
and use the engine brakes appropriate-
ly. If necessary, continuous shifting
down is possible. However, if down-
shifting more than 3 steps continuously,
the gear shifting will take more time.
DWhen the outside air temperature is
extremely low, the gear may not down-
shift from 2nd to 1st until the vehicle
stops.
DWhen the gear is shifting, a noise can
be heard in some case. This is not a
malfunction.
DIn case the transmission cannot be en-
gaged to a certain gear position during
shifting due to mechanical malfunction,
the gear will not be engaged and re-
mains in neutral. The “N” in the gear
position indicator will blink and a warn-
ing buzzer (long pulse sound) will
sound until the driver shifts the shift
lever to “N” position.
Unless the system recovers from the
above−mentioned condition (mechanical
malfunction), the gear will still remain
in neutral position even shifting the
shift lever to “M” or “E” position after
the system performs a re−try shifting.
If such conditions continue, contact any
authorized Toyota dealer or repairer, or
another duly qualified and equipped
professional, as soon as possible to
service the vehicle.
DWhen the gear jumped out of position
while driving, the gear is shifted to
proper gear position.
NOTICE
Manual (M) mode dose not shift up
the gear even if the engine speed
reaches the rev−limit.
11 02.18
AYGO WE 99E37E

148ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
Maximum allowable speeds
To get on a highway or to pass slower
traffic, maximum acceleration may be nec-
essary. Make sure you observe the follow-
ing maximum allowable speeds in each
gear:
gear km/h (mph)
1 51 (31)
2 95 (59)
3 139 (86)
CAUTION
DBe careful when accelerating, up-
shifting, downshifting or braking on
a slippery surface. Sudden accelera-
tion or engine braking could cause
the vehicle to spin or skid.
DTo drive down a long or steep hill,
reduce your speed and downshift.
Remember, if you ride the brakes
excessively, they may overheat and
fail.
DDuring driving the vehicle, do not
shift the shift lever to “N”. The en-
gine brake may not work and you
may get involved in an unexpected
accident. If you return the shift le-
ver from “N” to “M” because of an
unintended shifting, the gear posi-
tion will be changed accordingly to
the current vehicle speed.
DDo not apply the parking brake
while driving. Otherwise, it could
cause a skid and you may get in-
volved in an unexpected accident.
NOTICE
zThe system will not allow shifting
up or down to a gear that would
cause engine over−revving or un-
der−revving. In case of selecting a
gear position that may cause over−
revving, a warning buzzer (short
pulse sound) will sound.
zFrequent downshifting (more than 3
positions continuously) causes the
reduction of transmission life.
(b) Starting off
1. Start the engine as instructed in “How
to start the engine” on page 210 in
Section 3.
2. With your foot holding down the brake
pedal, shift the shift lever to the “M”
position properly. When the shift lever
is shifted to “M” position, the gear will
be shifted to 1st. On a slippery sur-
face, it is possible to start off with the
gear in 2nd. To start off with the gear
in 2nd, shift the shift lever from “N” to
“M” position, then operate the lever to
“+” direction. The gear will be shifted
to 2nd. Before starting off, always
make sure that the gear is engaged by
the gear position indicator, then de-
press the accelerator pedal.
NOTICE
Do not use 2nd gear to start off in
situations where the clutch load is
present such as when facing uphill.
If the gear cannot be engaged to 1st
or 2nd when the shift lever is shifted
from the “N” to “M” position, the “N”
indicator will blink and a warning buzz-
er (long pulse sound) will sound. In
this case, the system will re−try shift-
ing or the driver can operate the shift
lever to shift, as follows.
11 02.18
AYGO WE 99E37E

152ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
CAUTION
DWhen stopping, for example, at a
traffic light, be sure to depress the
brake pedal firmly. For your safety,
apply parking brake, too, when
stopping on a hill.
DWhen racing the engine, make sure
that the gear position is in the “N”
position by the gear position indica-
tor. In case the accelerator is oper-
ated with the gear in any other
position, the vehicle may move re-
sulting in an unexpected accident.
DDo not leave your vehicle unat-
tended while the engine is running.
DWhen leaving the vehicle, stop the
engine and park the vehicle with
the gear engaged. In case you need
to leave the vehicle with the engine
running, apply the parking brakes
firmly, and shift the shift lever in
the “N” position. When the driver ’s
door is opened with the shift lever
in the “M” position while stopping
with the engine running, warning
buzzer (long pulse sound) will
sound. If this happens on a hill
when starting off the vehicle, the
vehicle may move unexpectedly and
cause an accident.
NOTICE
zOn an uphill, never hold the vehicle
stop only by the accelerator pedal
operation or when the starting as-
sist system is being activated.
Otherwise the warning buzzer
(pulse sound) will sound and the
clutch may be damaged. In such a
case, pull over and shift the shift
lever to the “N” position. Wait for
around 15 minutes to cool the
clutch before starting again.
zIf the shift lever is operated more
than necessary, the system may not
allow operation of the shift lever
for a certain period of time, and the
gear may not be shifted appropri-
ately. Therefore, do not operate the
shift lever if not necessary.
(f) Parking
Unlike the automatic transmission, the
multi−mode manual transmission does not
have a parking position. The vehicle can
be parked with the shift lever in any posi-
tion.
1. Apply the parking brake firmly.
2. While depressing the brake pedal, shift
the shift lever in the “R” position on a
downhill or a level surface, and the
“M(1)” position on an uphill by confirm-
ing the gear position with the gear
position indicator.
3. Stop the engine.
11 02.18
AYGO WE 99E37E

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE157
Traction control system
The traction control system automatical-
ly helps control the spinning of front
wheels when the vehicle is started or
accelerated on slippery road surfaces.
When the engine switch is turned to the
“ON” position, the system automatically
turns on.
CAUTION
Under certain slippery road condi-
tions, full traction of the vehicle and
power against front wheels cannot be
maintained, even though the traction
control system is in operation. Do not
drive the vehicle under any speed or
maneuvering conditions which may
cause the vehicle to lose traction
control. In situations where the road
surface is covered with ice or snow,
your vehicle should be fitted with
snow tires or tire chains. Always
drive at an appropriate and cautious
speed for the present road condi-
tions.
MS16014
Leave the system on during the ordi-
nary driving so that it can operate
when needed.
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
begins to move. This means that the trac-
tion control system is in the self−check
mode, but does not indicate a malfunction.
When the traction control system isoper-
ating, the following conditions occur:
DThe system controls the spinning of the
front wheels. At this time, the slip indi-
cator light blinks.
DYou may feel vibration or noise in your
vehicle, caused by operation of the
brakes. This indicates the system is
functioning properly.
The slip indicator light comes on for a few
seconds when the engine switch is turned
to the “ON” position. If the indicator light
does not come on when the engine switch
is turned on, contact any authorized Toyo-
ta dealer or repairer, or another duly qual-
ified and equipped professional.
11 02.18
AYGO WE 99E37E