2011 TOYOTA AYGO stop start

156ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
Manual transmission
MS16001a
The shift pattern is as shown above.
Press the clutch pedal down fully while
shifting, and then release it slowly. Do not
rest your foot on the clutch pedal while
driving, because it will cause clutch
trouble. Do not use the clutch to hold the
vehicle when stopped on an uphill grade—
use the parking brake.
Upshifting too soon or downshifting too
late will cause lugging, and possibly ping-
ing. Regularly revving the engine to maxi-
mum speed in each gear will cause ex-
cessive engine wear and high fuel
consumption.
Maximum allowable speeds
To get on a highway or to pass slower
traffic, maximum acceleration may be nec-
essary. Make sure you observe the follow-
ing maximum allowable speeds in each
gear:
gear km/h (mph)
1 51 (31)
2 95 (59)
3 139 (86)
NOTICE
Do not downshift if you are going
faster than the maximum allowable
speed for the next gear down.
Good driving practice
If it is difficult to shift into reverse, put
the transmission in neutral, release the
clutch pedal momentarily, and then try
again.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to skid or
spin.
NOTICE
zDo not use any gears other than
first gear when starting off and
moving forward. Doing so may dam-
age the clutch.
zMake sure the vehicle is completely
stopped before shifting into reverse.
11 02.18
AYGO WE 99E37E

AUDIO SYSTEM169
SCAN
There are two scan features—you can ei-
ther scan the tracks on a specific disc or
scan the first tracks of all the discs in the
magazine.
Scanning the tracks on a disc:
Quickly push and release “SCAN”. “SCAN”
will appear on the display and the player
will scan all the tracks on the disc you
are listening to. If you hear a beep, you
held the button too long, and the player
will scan the first tracks of all the discs
in the magazine. To select a track, push
the “SCAN” a second time. If the player
scanned all the tracks on the disc, it will
stop scanning.
Compact disc changer only—
Scanning for the first tracks of all the
discs in the magazine:
Push and hold “SCAN” until you hear a
beep. “D−SCAN” will appear on the dis-
play and the player will perform the first
track of the next disc. To select a disc,
push the “SCAN” a second time. If the
player has scanned all the discs, it will
stop scanning.
ST (Stereo reception) display
Your radio automatically changes to stereo
reception when a stereo broadcast is re-
ceived. “ST” appears on the display. If the
signal becomes weak, the radio reduces
the amount of channel separation to prev-
ent the weak signal from creating noise.
If the signal becomes extremely weak, the
radio switches from stereo to mono recep-
tion.TA (Traffic Announcement)
This button is used for receiving TA sta-
tions all over the band.
EON (Enhanced Other Network) sys-
tem—If the RDS station (with EON data)
you are listening to is not broadcasting a
traffic information program at the TA (Traf-
fic Announcement) mode, the radio will be
switched to the traffic information program
automatically by using the EON AF list.
After the traffic information ends, the radio
will return to the initial program automati-
cally. A beep will sound to tell you when
this feature starts and ends the operation.
When receiving FM:
Push “TA” to switch the radio mode to TP
(Traffic Program). “TP” will appear on the
display.
In the TP mode, the radio will begin seek-
ing a TP station. If the radio seek out a
TP station, the program name will appear
on the display. If the TA station is re-
ceived, the radio will be switched to the
traffic information program automatically.
When the program ends, the initial opera-
tion resumes. When also in AF mode, the
radio will seek a TP station by using the
AF list.
Push “TA” once again to switch the radio
mode to TA. “TA” will appear on the dis-
play and the radio will mute the volume
of FM station.
In the TA mode, the radio will begin seek-
ing a TP station. It sounds only when a
TP station is received. When a TP station
is received, the program service name will
appear on the display. In the AF mode,
the radio will also begin seeking a TP
station by using the AF list.
While the radio is seeking a TP station,
“TP SEEK” appears on the display. If the
radio cannot seek out any TP stations,
“NOTHING” will appear on the display for
2 seconds and the radio will begin seek-
ing a TP station again.
AYGO WE 99E37E11 02.18

194INFORMATION BEFORE DRIVING YOUR TOYOTA
Break−in period
Drive gently and avoid high speeds.
Your vehicle does not need an elaborate
break−in. But following a few simple tips
for the first 1000 km (600 miles) can add
to the future economy and long life of
your vehicle:
DAvoid full throttle acceleration when
starting and driving.
DAvoid racing the engine.
DTry to avoid hard stops during the first
300 km (200 miles).
DDo not drive slowly with the manual
transmission in a high gear.
DDo not drive for a long time at any
single speed, either fast or slow.
Fuel
Selecting the proper fuel is essential
for satisfactory engine performance.
Engine damage caused by use of improp-
er fuels is not covered under Toyota’s new
vehicle warranty.
NOTICE
zDo not use improper fuels. If im-
proper fuels are used the engine
will be damaged.
zDo not use leaded gasoline on your
vehicle. Use of leaded gasoline will
cause damage to the engine. Also,
this can increase maintenance
costs.
zEU area: Bioethanol fuel sold under
names such as “E50” or “E85” and
fuel containing a large amount of
ethanol should not be used. The
use of these fuels will damage the
vehicle’s fuel system. In case of
any doubt, ask any authorized
Toyota dealer or repairer, or
another duly qualified and equipped
professional.
zExcept EU area: Bioethanol fuel
sold under names such as “E50” or
“E85” and fuel containing a large
amount of ethanol should not be
used. Your vehicle can use gasoline
mixed with 10% max ethanol. The
use of fuel with more than 10%
ethanol content (E10) will damage
the vehicle’s fuel system. You must
ensure that refueling is carried out
only from a source where fuel spec-
ification and quality can be guaran-
teed. In case of any doubt, ask any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional.
AYGO WE 99E37E11 02.18

196INFORMATION BEFORE DRIVING YOUR TOYOTA
The fuel pump shut off system stops sup-
plying fuel to the engine to minimize the
risk of fuel leakage when the engine stalls
or an airbag inflates upon collision. To
restart the engine after the fuel pump shut
off system activates, turn theengine
switch to “ACC” or “LOCK” once and start
it.
CAUTION
Inspect the ground under the vehicle
before restarting the engine. If you
find that fuel has leaked onto the
ground, the fuel system has been
damaged and is in need of repair. In
this case, do not restart the engine.
Operation in foreign countries
If you plan to drive your Toyota in
another country...
First,comply with the vehicle registration
laws.
Second,confirm the availability of the cor-
rect fuel.
AYGO WE 99E37E11 02.18
Fuel pump shut off system

200INFORMATION BEFORE DRIVING YOUR TOYOTA
Brake system
The tandem master cylinder brakesystem
is a hydraulic system with two separate
sub−systems. If either sub−system should
fail, the other will still work. However, the
pedal will be harder to press, and your
stopping distance will increase. Also, the
brake system warning light may come on.
CAUTION
Do not drive your vehicle with only a
single brake system. Have your
brakes fixed immediately.
BRAKE BOOSTER
The brake booster uses engine vacuum to
power−assist the brakes. If the engine
should quit while you are driving, you can
bringthevehicletoastopwithnormal
pedal pressure. There is enough reserved
vacuum for one or two stops—but no
more!
CAUTION
DDo not pump the brake pedal if the
engine stalls. Each push on the
pedal uses up the reserved vacuum.
DEven if the power assist is com-
pletely lost, the brakes will still
work. But you will have to push the
pedal hard, much harder than nor-
mal. And your braking distance will
increase.
ANTI−LOCK BRAKE SYSTEM
The anti−lock brake system is designed
to help prevent lock−up of the wheels
during a sudden braking or braking on
slippery road surfaces. This assists in
providing directional stability and steer-
ing performance of the vehicle under
these circumstances.
Effective way to press the ABS brake
pedal:
When the anti−lock brake system func-
tion is in action, you may feel the brake
pedal pulsating and hear a noise. In this
situation, to let the anti−lock brake sys-
tem work for you, just hold the brake
pedal down more firmly. Do not pump
the brake in a panic stop. This will re-
sult in reduced braking performance.
The anti−lock brake system becomes op-
erative after the vehicle has accelerated
to a speed in excess of approximately 10
km/h (6 mph). It stops operating when the
vehicle decelerates to a speed below
approximately 5 km/h (3 mph).
Depressing the brake pedal on slippery
road surfaces such as on a manhole cov-
er, a steel plate at a construction site,
joints in a bridge, etc. on a rainy day
tends to activate the anti−lock brake sys-
tem.
You may hear a click or motor sound in
the engine compartment for a few seconds
when the engine is started or just after
the vehicle begins to move. This means
that the anti−lock brake system is in self−
check mode, and does not indicate a mal-
function.
When the anti−lock brake system is ac-
tivated, the following conditions may
occur. They do not indicate a malfunc-
tion of the system:
AYGO WE 99E37E11 02.18

204INFORMATION BEFORE DRIVING YOUR TOYOTA
The electric power steering system, us-
ing an electric motor, assists the turn-
ing of the steering wheel.
In the following cases, you may feel the
steering becomes heavy. However, the
electric power steering system warning
light does not come on. (Because it is
not a malfunction.)
DWhen maneuvering or turning frequently
over a long time
The power steering effect will be re-
duced to prevent the system from over-
heating. Avoid turning the steering
wheel, or stop the vehicle and turn the
engine switch to “ACC” or “LOCK”. The
system will become cool inabout 10
minutes.
NOTICE
Frequent maneuvering and turning
over a long time may cause damage
to the system in which the mecha-
nism prevents overheating of the elec-
tric power steering system.
DWhen racing the engine for 30 seconds
or more with the vehicle stopped
The normal power steering effect will
be obtained when you start driving.
DWhen the battery is discharged
Check the battery’s condition. If
necessary, recharge or replace the
battery. For details, see “Checking
battery condition” on page 278 in
Section 7−3.
INFORMATION
When the steering wheel is turned, a
motor operating sound (whining
sound) may be heard. This occurs
when the power steering motor works
and is not defective.
MS21008
Electric power steering system warning
light
The light comes on when the engine
switch is turned to the “ON” position. If
the electric power steering system warning
light works properly, the light turns off
after a few seconds. If thesystem has
malfunctions, the light comes on again.
If either of the following conditions oc-
cur, this indicates a malfunction some-
where in the parts monitored by the
warning light system. Contact any au-
thorized Toyota dealer or repairer, or
another duly qualified and equipped
professional, as soon as possible to
service the vehicle.
DThe light does not come on when the
engine switch is turned to the “ON”
position or remains on.
DThe light stays on while you are driv-
ing.
The warning light turning on while racing
the engine for a long time may not indi-
cate malfunction. To turn off the light, re-
start the engine and start driving.
AYGO WE 99E37E11 02.18
Electric power steering
system

STARTING AND DRIVING211
Before starting the engine, be sure to
follow the instructions in “(a) Before
cranking”.
Normal starting procedure
The multiport fuel injection system/sequen-
tial multiport fuel injection system in your
engine automatically controls the proper
air−fuel mixture for starting. You can start
a cold or hot engine as follows:
Multi−mode manual transmission:With
your foot off the accelerator pedal, turn
the engine switch to the “START” posi-
tion and crank the engine while depress-
ing the brake pedal. Release the key
when the engine starts. The engine can-
not be cranked if the shift lever is in a
position except “N” or the brake pedal
is not depressed.
Manual transmission:With your foot off
the accelerator pedal, crank the engine
by turning the engine switch to the
“START” position. Release it when the
engine starts.
Engine should be warmed up by driving,
not idling. For warming up drive with a
smoothly turning engine until the engine
coolant temperature is within the normal
range.
If the engine stalls...
Simply restart it, using the correct proce-
dure given in normal starting.
If the engine will not start...
See “If your vehicle will not start” on page
220 in Section 4.
NOTICE
zDo not crank for more than 30 se-
conds at a time. This may overheat
the starter and wiring systems.
zDo not race a cold engine.
zIf the engine becomes difficult to
start or stalls frequently, have the
engine checked immediately.
Pre−trip safety check
It is a good idea to do a safety check
before starting out on a trip. A few min-
utes of checking can help ensure safe and
pleasant driving. Just a basic familiarity
with your vehicle is required and a careful
eye! Or, if you would like, any authorized
Toyota dealer or repairer, or another duly
qualified and equipped professional, will
be pleased to make this check for you at
nominal cost.
CAUTION
If you make this check in an enclosed
garage, make sure there is adequate
ventilation. Engine exhaust is poison-
ous.
BEFORE STARTING THE ENGINE
Outside the vehicle
Tires.Check the pressure with a gauge
and look carefully for cuts, damage, or
excessive wear.
Wheel bolts.Make sure no bolts are mis-
sing or loose.
Fluid leaks.After the vehicle has been
parked for a while, check underneath for
leaking fuel, oil, water, or fluid. (Water
dripping from the air conditioning after use
is normal.)
Lights.Make sure the headlights, stop
lights, tail lights, turn signals and other
lights are all working. Check the headlight
aim.
Inside the vehicle
Spare tire, jack and wheel bolt wrench.
Check the spare tire pressure and make
sure you have your jack and wheel bolt
wrench.
AYGO WE 99E37E11 02.18
(b) Starting the engine

212STARTING AND DRIVING
Seat belts.Check that the buckles lock
securely. Make sure the belts are not
worn or frayed.
Instruments and controls.Especially
make sure the service reminder indicators,
instrument lights, and defroster are work-
ing.
Brakes.Make sure the pedal has enough
clearance.
In the engine compartment
Spare fuses.Make sure you have spare
fuses. (See “Fuse locations” on page 259
in Section 7−1.)
Coolant level.Make sure the coolant lev-
el is correct. (See page 267 in Section
7−2 for instructions.)
Battery and cables.All the battery cells
should be filled to the proper level with
distilled water. Look for corroded or loose
terminals and a cracked case. Check the
cables for good condition and connections.
Wiring.Look for damaged, loose, or dis-
connected wires.
Fuel lines.Check the lines for leaks or
loose connections.
AFTER STARTING THE ENGINE
Exhaust system.Listen for any leakage.
Have any leaks fixed immediately. (See
“Engine exhaust cautions” on page 198 in
Section 2.)
Engine oil level.Stop the engine and
check the dipstick with the vehicle parked
on a level spot. (See page 264 in Section
7−2 for instructions.)
WHILE DRIVING
Instruments.Make sure the speedometer
and gauges are working.
Brakes.In a safe place, check that the
brakes do not pull to one side when ap-
plied.Anything unusual?Look for loose parts
and leaks. Listen for abnormal noises.
If everything looks O.K., set your mind at
ease and enjoy your trip!
AYGO WE 99E37E11 02.18