2011 TOYOTA AYGO stop start

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE143
MS16007a
(d) Backing up
After the vehicle has stopped completely,
hold down the brake pedal and shift the
shift lever to “R” position. A reverse buzz-
er will sound once at this time. Depress
the accelerator pedal slowly as when
starting off. Before driving off, make sure
that the gear is in reverse by using the
gear position indicator.
When the gear cannot be engaged even
when the shift lever is shifted from “N” to
“R” position, the “N” indicator will blink
and a warning buzzer (long pulse sound)
will sound. Thesystem will re−try shifting
automatically, or the driver can shift the
shift lever to “N” position once, then shift
to “R” again.
DThe system will re−try shifting automat-
ically. This will take some time, noise
may be heard from the gears, and shift
shock may occur. However, they do not
indicate malfunction.
NOTICE
zThe system will not allow shifting
to the “R” position if the vehicle
speed is over 6 km/h (3 mph). In
case the shift lever is operated un-
der this condition, the “N” indicator
in the instrument cluster will blink.
However, when the vehicle speed
drops below 6 km/h (3 mph), the
gear is shifted to reverse. Make
sure that the vehicle has stopped
completely before shifting to the
“R” position.
zOn an uphill, never hold the vehicle
stop only by the accelerator pedal
operation or when the starting as-
sist system is being activated.
Otherwise the warning buzzer
(pulse sound) will sound and the
clutch may be damaged. In such a
case, pull over and shift the shift
lever to the “N” position. Wait for
around 15 minutes to cool the
clutch before starting again.
zIf the gear cannot be engaged to
reverse when the shift lever is
shiftedfromthe“N”to“R”posi-
tion, try to shift the shift lever to
the “N” position once, then shift it
to “R” position a few seconds later.
11 02.18
AYGO WE 99E37E

144ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
(e) Stopping
The vehicle can be stopped by depressing
the brake pedal regardless of the gear
position. This is because the clutch is
automatically disengaged to prevent the
engine from stopping. If the shift lever is
in the “E” position, the gear will be down-
shifted to 1st when the vehicle stops.
In case the driver ’s door is opened with
the gear in “E”, “M” or “R” position and
without depressing the brake pedal, a
warning buzzer (long pulse sound) will
sound.
When the engine switch is “ON” and the
vehicle speed is slower than 9 km/h (5
mph), if the shift lever is in “N” position
and the brake pedal is released (not de-
pressed) for approximately 2 seconds, the
shift lever will be locked.
Shift lock system is designed for prevent-
ing the vehicle from starting off by the
unintended activation of the starting assist
system.
The shift lock can be released by de-
pressing the brake pedal without holding
the shift lever.
CAUTION
DWhen stopping, for example, at a
traffic light, be sure to depress the
brake pedal firmly. For your safety,
apply parking brake, too, when
stopping on a hill.
DWhen racing the engine, make sure
that the gear position is in the “N”
position by the gear position indica-
tor. In case the accelerator is oper-
ated with the gear in any other
position, the vehicle may move re-
sulting in an unexpected accident.
DDo not leave your vehicle unat-
tended while the engine is running.
DWhen leaving the vehicle, stop the
engine and park the vehicle with
the gear engaged. In case you need
to leave the vehicle with the engine
running, apply the parking brakes
firmly, and shift the shift lever in
the “N” position. When the driver ’s
door is opened with the shift lever
in the “E” position while stopping
with the engine running, warning
buzzer (long pulse sound) will
sound. If this happens on a hill
when starting off the vehicle, the
vehicle may move unexpectedly and
cause an accident.
11 02.18
AYGO WE 99E37E

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE145
NOTICE
zOn an uphill, never hold the vehicle
stop only by the accelerator pedal
operation or when the starting as-
sist system is being activated.
Otherwise the warning buzzer
(pulse sound) will sound and the
clutch may be damaged. In such a
case, pull over and shift the shift
lever to the “N” position. Wait for
around 15 minutes to cool the
clutch before starting again.
zIf the shift lever is operated more
than necessary, the system may not
allow operation of the shift lever
for a certain period of time, and the
gear may not be shifted appropri-
ately. Therefore, do not operate the
shift lever if not necessary.
(f) Parking
Unlike the automatic transmission, the
multi−mode manual transmission does not
have a parking position. The vehicle can
be parked with the shift lever in any posi-
tion.
1. Apply the parking brake firmly.
2. While depressing the brake pedal, shift
the shift lever in the “R” position on a
downhill or a level surface, and “E(1)”
position on an uphill by confirming the
gear position with the gear position in-
dicator.
3. Stop the engine.
MS16008
1: Uphill
2: Level or downhill
To stop the engine:
Check the transmission gear position by
the gear position indicator, then turn the
engine switch off to stop the engine. Re-
lease the brake pedal after a few sec-
onds. The shift lever will be locked in the
position just before the engine switch was
turned off.
You can check the gear position by the
gear position indicator within 5 seconds
after turning the engine switch off.
CAUTION
DIf the gear is not engaged properly
and completely before the engine
switch is turned off, the vehicle
may not be parked with the gear
engaged. Always confirm the gear
position with the gear position indi-
cator when parking.
DOn a level surface or a downhill,
the gear should be put in reverse,
and in the 1st on an uphill. Other-
wise, the vehicle may move, and
cause an unexpected accident. If
the gear is left in the “N” position,
the vehicle can not be parked with
the gear engaged.
11 02.18
AYGO WE 99E37E

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE149
DThe system will re−try shifting automat-
ically. This will take some time, noise
may be heard from the gears, and shift
shock may occur. However, they do not
indicate malfunction.
DThe driver may shift the shift lever to
the “N” position once, then shift to the
“M” position.
3. Release the parking brake and brake
pedal. Depress the accelerator pedal
slowly for smooth starting.
CAUTION
Always keep your foot on the brake
pedal while stopping with the engine
running. This operation prevents the
vehicle from starting by an unin-
tended activation of the starting as-
sist system.
NOTICE
zOn a slippery surface, it is possible
to start off with the gear in 2nd,
but to protect the clutch, try to
start using the 1st gear whenever
possible.
zIf the gear cannot be engaged to
1st or 2nd when the shift lever is
shifted from the “N” to “M” posi-
tion, try to shift the shift lever to
the “N” position once, then shift it
to “M” position a few seconds later.
Do not operate the system in the fol-
lowing manners. A life cycle of the
clutch may be reduced. If you do
these operation, a warning buzzer will
sound.
zStopping by the accelerator pedal
operation with the shift lever in the
“M” or “E” position on an uphill.
zThe shift lever is shifted to the
“M”, “E” or “R” position while rac-
ing the engine.
zDriving with low speed using high
gear position.
zBeing stopped on a slope using the
starting assist system.
(c) Starting off on an uphill/downhill
—Uphill
1. Apply the parking brake firmly so that
the vehicle does not roll backwards.
2. Shift the shift lever to the “M” position
while holding down the brake pedal.
Make sure that the gear position indi-
cator in the instrumental cluster dis-
plays 1st gear.
3. Release the brake pedal and depress
the accelerator pedal gradually, and
when the vehicle starts to move, re-
lease the parking brake and depress
the accelerator pedal to start off.
—Downhill
1. Hold down the brake pedal and shift
the shift lever to the “M” position.
Make sure by using the gear position
indicator that the gear is in 1st.
2. Release the brake pedal and depress
the accelerator pedal slowly. Even
though the accelerator pedal is not de-
pressed, the clutch will be engaged
when the vehicle speed increases.
11 02.18
AYGO WE 99E37E

150ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
NOTICE
On an uphill, never hold the vehicle
stop only by the accelerator pedal op-
eration or when the starting assist
system is being activated. Otherwise
the warning buzzer (pulse sound) will
sound and the clutch may be dam-
aged. In such a case, pull over and
shift the shift lever to the “N” posi-
tion. Wait for around 15 minutes to
cool the clutch before starting again.
MS16007a
(d) Backing up
After the vehicle has stopped completely,
hold down the brake pedal and shift the
shift lever to “R” position. A reverse buzz-
er will sound once at this time. Depress
the accelerator pedal slowly as when
starting off. Before driving off, make sure
that the gear is in reverse by using the
gear position indicator.
When the gear cannot be engaged even
when the shift lever is shifted from “N” to
“R” position, the “N” indicator will blink
and a warning buzzer (long pulse sound)
will sound. Thesystem will re−try shifting
automatically, or the driver can shift the
shift lever to “N” position once, then shift
to “R” again.
DThe system will re−try shifting automat-
ically. This will take some time, noise
may be heard from the gears, and shift
shock may occur. However, they do not
indicate malfunction.
11 02.18
AYGO WE 99E37E

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE151
NOTICE
zThe system will not allow shifting
to the “R” position if the vehicle
speed is over 6 km/h (3 mph). In
case the shift lever is operated un-
der this condition, the “N” indicator
in the instrument cluster will blink.
However, when the vehicle speed
drops below 6 km/h (3 mph), the
gear is shifted to reverse. Make
sure that the vehicle has stopped
completely before shifting to the
“R” position.
zOn an uphill, never hold the vehicle
stop only by the accelerator pedal
operation or when the starting as-
sist system is being activated.
Otherwise the warning buzzer
(pulse sound) will sound and the
clutch may be damaged. In such a
case, pull over and shift the shift
lever to the “N” position. Wait for
around 15 minutes to cool the
clutch before starting again.
zIf the gear cannot be engaged to
reverse when the shift lever is
shifted from the “N” to “R” posi-
tion, try to shift the shift lever to
the “N” position once, then shift it
to “R” position a few seconds later.
(e) Stopping
The vehicle can be stopped by depressing
the brake pedal regardless of the gear
position. This is because the clutch is
automatically disengaged to prevent the
engine from stopping. If the shift lever is
in the “M” position, the gear will be down-
shifted to 1st when the vehicle stops.
However, if you do not drive the vehicle
over 40 km/h (24 mph) or convert the
drive position after starting with the gear
in 2nd, the gear will not be downshifted
to 1st when the vehicle stops the next
time and the gear is left in 2nd.
In case the driver ’s door is opened with
the gear in “M”, “E” or “R” position and
without depressing the brake pedal, a
warning buzzer (long pulse sound) will
sound.
When the engine switch is “ON” and the
vehicle speed is slower than 9 km/h (5
mph), the shift lever will be locked if the
shift lever is in “N” position and the brake
pedal is released for approximately 2 sec-
onds.
Shift lock system is designed for prevent-
ing the vehicle from starting off by the
unintended activation of the starting assist
system.
The shift lock can be released by de-
pressing the brake pedal without holding
the shift lever.
11 02.18
AYGO WE 99E37E

152ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
CAUTION
DWhen stopping, for example, at a
traffic light, be sure to depress the
brake pedal firmly. For your safety,
apply parking brake, too, when
stopping on a hill.
DWhen racing the engine, make sure
that the gear position is in the “N”
position by the gear position indica-
tor. In case the accelerator is oper-
ated with the gear in any other
position, the vehicle may move re-
sulting in an unexpected accident.
DDo not leave your vehicle unat-
tended while the engine is running.
DWhen leaving the vehicle, stop the
engine and park the vehicle with
the gear engaged. In case you need
to leave the vehicle with the engine
running, apply the parking brakes
firmly, and shift the shift lever in
the “N” position. When the driver ’s
door is opened with the shift lever
in the “M” position while stopping
with the engine running, warning
buzzer (long pulse sound) will
sound. If this happens on a hill
when starting off the vehicle, the
vehicle may move unexpectedly and
cause an accident.
NOTICE
zOn an uphill, never hold the vehicle
stop only by the accelerator pedal
operation or when the starting as-
sist system is being activated.
Otherwise the warning buzzer
(pulse sound) will sound and the
clutch may be damaged. In such a
case, pull over and shift the shift
lever to the “N” position. Wait for
around 15 minutes to cool the
clutch before starting again.
zIf the shift lever is operated more
than necessary, the system may not
allow operation of the shift lever
for a certain period of time, and the
gear may not be shifted appropri-
ately. Therefore, do not operate the
shift lever if not necessary.
(f) Parking
Unlike the automatic transmission, the
multi−mode manual transmission does not
have a parking position. The vehicle can
be parked with the shift lever in any posi-
tion.
1. Apply the parking brake firmly.
2. While depressing the brake pedal, shift
the shift lever in the “R” position on a
downhill or a level surface, and the
“M(1)” position on an uphill by confirm-
ing the gear position with the gear
position indicator.
3. Stop the engine.
11 02.18
AYGO WE 99E37E

154ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
A warning buzzer will sound or the indica-
tor will blink under the following condi-
tions:
Warning buzzer (long pulse sound)
DThe buzzer will sound if the starting
assist system is being activated for a
long period of time.
DThe engine switch is turned to the
“OFF” position with the gear in 2nd or
either 3rd, 4th or 5th.
In this case, turn the engine switch to the
“ON” position and shift the shift lever in
the “N” position, then shift it to the “E” or
“M” or “R” position, then turn the engine
switch to “OFF”.
DDuring a stop, the driver ’s door is
opened with the shift lever in the “R”,
“E” or “M” position while the engine is
running.
Warning buzzer (continuously sound)
During a stop, the driver ’s door is opened
with the shift lever in the “R”, “E” or “M”
position while the engine is running.
Warning buzzer (pulse sound)
The clutch is heated with excessive load.
NOTICE
In these cases, pull over and shift the
shift lever to the “N” position. Wait
for around 15 minutes to cool down
the clutch before starting again.
Otherwise the clutch may be dam-
aged.
Warning buzzer (short pulse sound)
DThe transmission is shifted down to a
gear where the engine is over−revving.
DThe buzzer will sound once when the
shift lever is shifted to the “R” position.
MS16011
“N” indicator blinking
When the gear indicator lamp blinks “N”,
perform any one of the following opera-
tions:
DShift the shift lever to the “N” position
once, and wait for a few seconds, shift
the shift lever again to the “E”, “M” or
“R” position.
DShift the shift lever to the “N” position
once and confirm that the engine has
started. Then, shift the shift lever to
the “E”, “M” or “R” position.
DTurn the engine switch “ON” before op-
erate the shift lever. Shift the shift le-
ver to the “N” position once, then shift
the shift lever again to the “E”, “M” or
“R” position.
“N” indicator blinking and warning
buzzer (long pulse sound) beeping.
If this condition would remain for a long
period of time, make sure the engine
switch is being “ON” and then shift the
shift lever to “N”. After the operation, shift
the shift lever to “E”, “M” or “R”.
11 02.18
AYGO WE 99E37E
—Warning functions