2011 SKODA OCTAVIA reset

–
Service interval - Display of the remaining number of days, kilometres or
miles to the next Inspection Service/Reset 1)
– Reset trip counter for distance driven
– Resetting Service Interval Display
– Activate/deactivate display mode
Fuel gauge ⇒ page 11 
Engine revolutions counter The red zone of the rev counter scale
1 ⇒ fig. 2
indicates the range in which the
engine control unit begins to limit the engine speed. The engine control unit re-
stricts the engine speed to a steady limit value.
Shift into the next higher gear or select the selector lever position D of the auto-
matic gearbox before reaching the red zone of the rev counter scale.
Avoid high engine speeds during the driving time and before the engine has been
warmed up to operating temperature ⇒ page 161
. For the sake of the environment
Shifting to a higher gear in good time helps to reduce the fuel consumption, mini-
mises operating noise levels, protects the environment and contributes to a lon-
ger life and reliability of the engine. 
Speedometer Warning against excessive speeds
An acoustic warning signal will sound when the vehicle speed exceeds 120 kilo-
metres per hour. The acoustic warning signal will switch off again when the vehi-
cle speed goes below this speed limit.

Coolant temperature gauge The coolant temperature gauge
3
⇒  fig. 2
operates only when the ignition is
switched on. 6 Please pay attention to the following guidelines regarding temperature ranges in
order to avoid damage to the engine:
Cold range
If the pointer is in the left-hand area of the scale it means that the engine has not
yet reached its operating temperature. Avoid running at high engine speeds, at
full throttle and at severe engine loads.
The operating range
The engine has reached its operating temperature as soon as the pointer moves
into the mid-range of the scale. The pointer may also move further to the right at
high engine loads and high outside temperatures. This is not critical provided the
warning symbol  in the instrument cluster does not flash.
If the symbol  in the instrument cluster flashes it means that either the coolant
temperature is too high or the coolant level is too low. Please refer to the guide-
lines ⇒ page 25, Coolant temperature/ Coolant quantity . WARNING
Pay attention to the warning notes ⇒ page 181, Working in the engine com-
partment
before opening the bonnet and inspecting the coolant level. CAUTION
Additional headlights and other attached components in front of the fresh air inlet
impair the cooling efficiency of the coolant. There is then a risk of the engine
overheating at high outside temperatures and high engine loads! 
Fuel gauge The fuel gauge
6
⇒
 fig. 2 only operates when the ignition is switched on.
The fuel tank has a capacity of about 55 litres or 60 litres 2)
. The warning symbol 
in the instrument cluster lights up when the pointer reaches the reserve marking.
There are now about 9 litres of fuel remaining in the tank. This symbol is a re-
minder for you, that you must refuel .
The following is displayed in the information display: £1)
Valid for countries where the values are indicated in British measuring units.
2) Valid for Octavia Combi 4x4 and Octavia Scout. 11
Instruments and warning lights Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

Please refuel!
An audible signal sounds as an additional warning signal. CAUTION
Never run the fuel tank completely empty! An irregular supply of fuel can lead to
irregular engine running. Unburnt fuel may get into the exhaust system and dam-
age the catalytic converter. Note
After filling up, it can occur that during dynamic driving (e.g. numerous curves,
braking, driving downhill and climbing a steep hill) the fuel gauge indicates ap-
prox. a fraction less. When stopping or during less dynamic driving, the correct fuel
supply quantity is indicated. This effect is not a fault. 
Counter for distance driven The distance which you have driven with your vehicle is shown in kilometres (km).
In some countries the measuring unit
“mile” is used.
Reset button
If you hold the reset button 5
⇒
 fig. 2 pressed for about 1 second, the trip counter
is set back to zero.
Trip counter for distance driven
The trip counter indicates the distance which you have driven since this counter
was last reset - in steps of 100 metres or 1/10 of a mile.
Counter for distance driven
The counter for distance driven indicates the total distance in kilometres or miles
which the vehicle has been driven.
Fault display
If there is a fault in the instrument cluster Error will appear continuously in the
display. Have the fault rectified as soon as possible by a specialist workshop. WARNING
Never seek to adjust the trip counter for distance driven while driving for
safety reasons! Note
If vehicles which are fitted with the information display the display of the second
speed is activated in mph or km/h, this driving speed is indicated instead of the
counter for the total distance driven. 
Service reminder indicator Fig. 3 Service Interval Display: Note
Depending on the equipment installed in the vehicle, the text can differ on the
display.
Service Interval Display
Before the next service interval a key symbol 
and the remaining kilometres are
indicated after switching on the ignition ⇒ fig. 3 . At the same time, a display ap-
pears regarding the remaining days until the next service interval.
The following is displayed in the information display:
Service after ... km or... days. (Service after ... km or ... days.)
The kilometre indicator or the days indicator reduces in steps of 100 km. or days
until the service due date is reached.
A flashing key symbol 
and the text Service appears in the display for 20 sec-
onds as soon as the due date for the service is reached.
The following is displayed in the information display:
Service now! (Service now!)
Display regarding the distance and days until the following service interval
You can use the button 5 to display the remaining distance driven and the days
until the next service interval ⇒

 fig. 2. £12
Instruments and warning lights

A key symbol  and a display regarding the remaining kilometres appear for 10
second in the display. At the same time, a display appears regarding the remaining
days until the next service interval.
On vehicles which are equipped with an information display, you can call up this
display in the menu
Settings ⇒ page 19
.
The following will be displayed in the information display for 10 seconds:
Service after ... km or... days. (Service after ... km or ... days.)
Resetting Service Interval Display
It is only possible to reset the Service Interval Display, if a service message or at
least a pre-warning is shown on the display of the instrument cluster.
We recommend having this resetting performed by a specialist garage.
The specialist garage:
● resets the memory of the display after the appropriate inspection,
● makes an entry in the Service schedule,
● affix the sticker with the entry of the following service interval to the side of
the dash panel on the driver's side.
Reset the service interval displays by using the button 5
⇒  fig. 2.
On vehicles which are equipped with an information display, you can call up this
display in the menu Settings ⇒ page 19

. CAUTION
We recommend that you do not reset the Service Interval Display yourself other-
wise this can result in the service interval display being incorrectly set, which may
also result in problems with operation of your vehicle. Note
● Never reset the display between service intervals otherwise this may result in
incorrect readouts.
● information is retained in the Service Interval Display also after the battery of
the vehicle is disconnected.
● If the instrument cluster is exchanged after a repair, the correct values must
be entered in the counter for the Service Interval Display. This work is carried out
by a specialist garage. ●
The data displayed is the same after resetting the display with flexible service
intervals (QG1) is displayed as that for a vehicle with fixed service intervals (QG2).
We therefore recommend having the Service Interval Display reset only by an au-
thorised

ŠKODA Service Partner who is familiar with the procedure for resetting
the display with a vehicle system tester.
● Please refer to the brochure Service schedule for extensive information about
the service intervals. 
Digital clock You can set the time with the rotary knob
5 ⇒
 
fig. 2.
Select the information which you wish to change by turning the button 5 and
carry out the change of the selected information by pressing the button.
On vehicles which are fitted with the information display, it is possible to set the
time in the menu Time ⇒

  page 19. WARNING
The clock should not be adjusted while driving for safety reasons but only
when the vehicle is stationary! 
Shift recommendation for changing gears Fig. 4 Shift recommendation for chang-
ing gears
An information for the engaged gear A
⇒  fig. 4 is shown in the display of the in-
strument cluster.
In order to minimise the fuel consumption, a recommendation for shifting into an-
other gear is indicated in the display. £ 13
Instruments and warning lights Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

Note
All information in the memory 1 and 2 is erased if the battery of the vehicle is dis-
connected. 
Operating with the buttons on the windshield wiper lever and on
the multifunction steering wheel Fig. 6 Multi-functional indicator: Controls on the windshield wiper lever/controls on the mul-
tifunction steering wheel
The rocker switch A and the button
B are located on the windshield wiper lever
⇒  fig. 6 . Switching over and resetting is performed with the handwheel D on the
multifunction steering wheel.
Selecting the memory
– After briefly pressing the button B on the windshield wiper lever or by briefly
pressing the button D on the multifunction steering wheel, you can select the
desired memory.
Selecting the functions with the help of the windshield wiper lever
– Press the top or bottom rocker switch A for longer than 0.5 seconds. In this
way, call up in sequence the individual functions of the multi-functional indica-
tor.
Selecting the functions with the help of the multifunction steering wheel
– By pressing the button C , you can call up the menu of the multi-functional in-
dicator.
– Turn the handwheel D upwards or downwards. In this way, call up in se-
quence the individual functions of the multi-functional indicator. Setting function to zero
–
Select the memory you want.
– Press the button B or
D for more than 1 second.
The following readouts of the selected memory will be set to zero with the button B on the windshield wiper lever or with the button
D on the multifunction steer-
ing wheel:
● average fuel consumption,
● distance driven,
● average speed,
● Driving time.
You can only operate the multi-functional indicator when the ignition is switched
on. After the ignition is switched on, the function displayed is the one which you
last selected before switching off the ignition. 
Outside temperature The outside temperature appears in the display when the ignition is switched on.
If the outside temperature drops below +4
°C, a snow flake symbol (warning signal
for ice on the road) appears before the temperature indicator and a warning signal
sounds. After pressing the rocker switch A at the windshield wiper lever
⇒ fig. 6
or the button C at the multifunction steering wheel
⇒
 fig. 6 , the function shown
last is indicated. WARNING
Do not only rely upon the information given on the outside temperature dis-
play that there is no ice on the road. Please note that black ice may also be
present on the road surface even at temperatures around +4

°C – warning,
drive with care! 
Driving time The driving time which has elapsed since the memory was last erased, appears in
the display. If you wish to measure the driving time as of a particular time, you
must set the memory to zero at this moment in time by pressing the button
B on
the windshield wiper lever ⇒ fig. 6 or the handwheel D on the multifunction
steering wheel ⇒ fig. 6 for longer than 1

second. £ 15
Instruments and warning lights Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data

Second speed
Here you can switch on the display of the second speed in mph or in km/h
1)
.
Service
Here you can have the kilometres still to be driven and the days until the follow-
ing service interval shown and the Service Interval Display reset. Factory Setting
After selecting the menu
Factory Setting the factory setting of the information
display is established again. 
Warning lights
Overview The warning lights indicate certain functions or faults.
Fig. 8 Instrument cluster with warning lights
 Turn signal lights (to the left)
⇒ page 23
 Turn signal lights (to the right)
⇒ page 23 
Fog lights
⇒ page 23
 Main beam
⇒ page 23 £1)
Valid for countries where the values are indicated in British measuring units. 21
Instruments and warning lights Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical data