2011 Seat Altea XL fold seats

Seats and storage compartments143
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Folding the seat backrests down – Pull the loop on the side of the seat ⇒fig. 100 In this position the backrest is locked. This is the reason why the loop located
o n the si d e of the sea t m us t be pulled in th e d ire ct io n of t he a r row to op e n t he
backrest.
WARNING
•You should check that the backrest has engaged properly in position
after the loop is released.•For safety reasons the locking system loops on the seats may not be
used to secure any items.
Folding the rear seat backrests down– Pull the loop on the side of the seat ⇒fig. 101 in the direc-
tion of the arrow and lift the seat backrest into position.
WARNING
•You should check that the backrest has engaged properly in position
after the loop is released.•For safety reasons the locking system loops on the seats may not be
used to secure any items.•After locking the seat backrest into position ensure that the seat belts
protrude from the seat.
Fig. 100 Folding or
opening the rear seat
backrests
A1
Fig. 101 Folding or
opening the front seat
backrests
A1
AlteaXL_EN.book Seite 143 Donnerstag, 9. September 2010 12:13 12

Seats and storage compartments145
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Note
The CD changer is located in this compartment.Storage areas under the front seats*
There is a storage locker with a cover under each front seat.The drawer* ⇒fig. 104 is opened by pushing the button and putting the
cover back.
There are two open positions of 15 and 60 degrees depending on the pres-
sure applied to the cover. In the 60 degree position, the cover will collapse if
too much pressure is applied.
To close the drawer, press the cover until it locks into position.
WARNING
•The drawers will hold a maximum weight of 1.5 kg.•Do not drive with the drawer cover open. There is an injury risk for
passengers if the cargo is released in case of sudden braking or an
accident.
Folding tray*
Folding trays are fitted to the rear of the front seat backrests.– To open the tray, open it up in the direction of the arrow ⇒fig. 105 .
Fig. 104 Storage area
under the front seats
AA
Fig. 105 Folding tray on
the front left seat
AlteaXL_EN.book Seite 145 Donnerstag, 9. September 2010 12:13 12

Seats and storage compartments
146
WARNING
•The folding trays may not be folded down whilst the vehicle is in motion
and anyone is seated on the second row of seats. There is a risk on injury
during a sudden braking manoeuvre! The tray must therefore be closed and
properly secured whilst the vehicle is in motion.•Never place hot drinks in the cup holders. During normal or sudden
driving manoeuvres, sudden braking or an accident, the hot drink could be
spilled. Danger of scalding.Caution
When driving, do not leave open cans in the cup holders. The drink might be
spilt on braking, for example, and could damage the vehicle.Roof storage compartment*
There are four storage compartments in the roof
– Press the button on the cover to open these compartments ⇒fig. 106 . The cover will then open.
– To close the cover, press it up until it engages.
WARNING
Always keep the storage area cover closed while the vehicle is in motion to
reduce the risk of injury during a sudden braking manoeuvre or in the event
of an accident and to prevent any items from being thrown through the
vehicle interior.
Fig. 106 Roof storage
compartments
AlteaXL_EN.book Seite 146 Donnerstag, 9. September 2010 12:13 12

Seats and storage compartments147
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Storage in the luggage compartment*
There is a variable storage area* in the luggage compartment
floor.
– Lift the luggage compartment floor and fold it back all the way
⇒fig. 107 .
–Fit the separator ⇒fig. 108 into the side grooves depending
on the size of the objects to be transported. The on-board tool kit
and the spare wheel are located underneath the luggage
compartment.
– Secure objects in the luggage compartment with suitable straps on the fastening rings.
Note•Do not exceed the maximum authorised weight for the vehicle
⇒ page 293.
Fig. 107 Variable
luggage compartment
floor storage compart-
mentFig. 108 Variable
luggage compartment
floor storage compart-
ment
AA
AlteaXL_EN.book Seite 147 Donnerstag, 9. September 2010 12:13 12

Seats and storage compartments
150
Opening and closing the armrest*/ drink holder*
– To open, pull the loop in the direction of the arrow ⇒page 149,
fig. 111 .
– To close, lift the Drink holder*/ armrest* in the direction of the arrow ⇒page 149, fig. 112 .
WARNING
Ensure that the load in the luggage compartment is correctly secured with
the retainer net when travelling with the armrest down ⇒page 148.Multi-purpose mobile storage compartment* - Fitting and removal
This storage compartment may only be placed in the central
area of the rear seat
Fitting mobile storage compartment
– Fold down the small section of the rear seat backrest, in order to
access the large section of the backrest.
– Fit the mobile storage compartment mounting plate ⇒fig. 114 from the inside of the vehicle, through the rear
section of the seat. It should be fitted between the backrest and
the seat, in the central seat area.
– Push the plate until it clips the cushion frame. The rings of the mobile storage compartment mounting plate appear at the front
of the seat.
– If it is difficult to make the plate clip, tilt the rear backrest of the large section forwards slightly an d then lean the backrest back-
wards to make the fitting of the mobile storage compartment
onto the mounting plate easier.
A1
A2
Fig. 113 Mobile storage
compartment. Installation
Fig. 114 Mobile storage
compartment mounting
plate
AH
AlteaXL_EN.book Seite 150 Donnerstag, 9. September 2010 12:13 12

Seats and storage compartments151
Safety First
Operating Instructions
Practical Tips
Technical Specifications
– Place the mobile storage compartment onto the foam of the
central seat.
– Set both mounting pieces together ⇒page 150, fig. 113 ,
with both mounting rings ⇒page 150, fig. 114 and press
hard until both the clips completely connect with the rings.
Removing mobile storage compartment
– Pull each of the buttons ⇒ page 150, fig. 113 on the clips
(red buttons) forwards, until they snap out of place.
– Fold the larger seat down and remove the mobile storage compartment mounting plate.
Multi-purpose mobile storage compartment* - General information
This storage compartment may only be placed in the central
area of the rear seat
AE
AG
AF
Fig. 115 Mobile storage
compartment. OpeningFig. 116 Mobile storage
compartment. Functions
AlteaXL_EN.book Seite 151 Donnerstag, 9. September 2010 12:13 12

Seats and storage compartments159
Safety First
Operating Instructions
Practical Tips
Technical Specifications
Partition net*
The net partition prevents loose objects in the luggage
compartment from being thrown forward into the passenger
compartment (e.g. under sudden braking).
– Pull the net from underneath between the backrest and the
folding tray and fit it to the slots in the roof, first the right then the
left ⇒fig. 126 .
– Hook the belts into the front anchor rings to tense the net ⇒fig. 127 .Roof rack*Please observe the following points if you intend to carry loads on the roof:•For safety reasons, only luggage racks and accessories approved by SEAT
should be used.•It is essential that you follow the assembly instructions included with the
bars exactly, being especially careful to position the front and rear luggage
compartment cover bars on the special housings on the longitudinal bars.
You must also respect their position according to the direction of travel indi-
cated in the assembly manual. Not following these instructions may cause
marks on the longitudinal bars.•Distribute the load evenly. A maximum load of 40 kg only is permitted for
each roof rack system support bar, the load must be distributed evenly along
the entire length. However, the maximum load permitted for the entire roof
(including the support system) of 75 kg must not be exceeded nor should the
total weight of the vehicle be exceeded. See the Technical Data section.•When transporting heavy or large objects on the roof, any change in the
normal vehicle behaviour due to a change in the centre of gravity or an
increased wind resistance must be taken into account. For this reason, a suit-
able speed and driving style must be used.•For those vehicles fitted with a sunroof*, ensure that it does not interfere
with the load on the roof rack system when opened.
Fig. 126 Partition netFig. 127 Anchor rings for
the separation net
AlteaXL_EN.book Seite 159 Donnerstag, 9. September 2010 12:13 12